Download Print this page

FireMagic Aurora A430i Installation Instructions And Owner's Manual

Built-in outdoor gas grills
Hide thumbs

Advertisement

BUILT-IN OUTDOOR GAS GRILLS
A430i, A530i, A540i, A660i, & A790i
INSTALLATION
INSTRUCTIONS AND
OWNER'S MANUAL
INSTALLER:
Leave these instructions with consumer.
CONSUMER:
Retain for future reference.
IMPORTANT:
READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.
DANGER:
IF YOU SMELL GAS
1. Shut off the gas to the appliance.
2. Extinguish any open fl ame.
3. Open lid.
4. If odor continues, keep away from the
appliance and immediately call your
gas supplier or the fi re department.
CODE AND SUPPLY REQUIREMENTS: This
grill must be installed in accordance with local
codes and ordinances, or, in the absence of local
codes, with the latest National Fuel Gas Code
(ANSI Z223.1/NFPA 54), or Natural Gas and
Propane Storage and Handling Installation Code
(CSA-B149.1).
This appliance and its dedicated manual shutoff
valve must be disconnected from the gas-supply
piping system when testing the system at pressures
in excess of ½ psig (3.5 kPa).
This appliance must be isolated from the gas-
supply piping system by closing its dedicated
manual shutoff valve during any pressure testing
of the gas-supply system at pressures up to and
including ½ psig (3.5 kPa).
Proper operation of your grill
requires prompt and periodic
maintenance. See the CARE &
CLEANING section for details.
Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746
REV 1 - 1509290845
WARNINGS AND SAFETY CODES
:
A790i w/ digital thermometer shown
WARNING:
1. Do not store or use gasoline or other
fl ammable vapors and liquids in the
vicinity of this or any other appliance.
2. An LP cylinder not connected for use
shall not be stored in the vicinity of this
or any other appliance.
WARNING:
Improper installation, adjustment, alteration,
service, or maintenance can cause injury
or property damage. For proper installation,
refer to the installation instructions. For
assistance or additional information, consult
a qualifi ed professional installer, service
agency, or the gas supplier.
All electrical outlets in the vicinity of the grill must
be properly grounded in accordance with local
codes, or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the
Canadian Electrical Code, CSA C22.1, whichever
is applicable.
Keep all electrical-supply cords and fuel-supply
hoses away from any heated surface.
Certifi ed to:
11-093
1
ANSI Z21.58b-2012
CSA 1.6b-2012
L-C2-434

Advertisement

loading

  Related Manuals for FireMagic Aurora A430i

  Summary of Contents for FireMagic Aurora A430i

  • Page 1 BUILT-IN OUTDOOR GAS GRILLS A430i, A530i, A540i, A660i, & A790i INSTALLATION INSTRUCTIONS AND OWNER’S MANUAL INSTALLER: Leave these instructions with consumer. A790i w/ digital thermometer shown CONSUMER: Retain for future reference. IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE. WARNINGS AND SAFETY CODES DANGER: WARNING:...
  • Page 2 INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE GRIL EXTÉRIEUR DE GAZ DU BUILT-IN IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION SÛRETÉ ET CODES D’AVERTISSEMENT DANGER: AVERTISSEMENT: 1. Ne stockez pas ou n’employez pas SI VOUS SENTEZ LE GAZ l’essence ou d’autres vapeurs et liquides 1.
  • Page 3: Table Of Contents

    CONTENTS GETTING STARTED INSTALLATION ........REPLACEMENT PARTS LIST ............INSTALLATION ................... MODEL SPECIFICATIONS COUNTER PREPARATION ............BUILT-IN GRILL DIMENSIONS TABLE CONNECT THE GAS SUPPLY ................. INSTALL THE FLAVOR GRIDS COUNTERTOP OVERHANG ....................SUBSTRATE ELECTRICAL INSTALLATION ..............
  • Page 4: Getting Started

    GETTING STARTED REPLACEMENT PARTS LIST S o m e i t e m s s h ow n are optional, or are not available for certain models. Your model may vary, refer to parts To order replacement table. par ts, contact your ®...
  • Page 5 REPLACEMENT PARTS LIST (cont.) A430i A530i A540i A660i A790i Item Description Part No. Qty. Part No. Qty. Part No. Qty. Part No. Qty. Part No. Qty. Stainless cooking grid (set of 2 or 3) 23542-S-2 23539-S-2 23543-S-3 23544-S-3 23539-S-3 Flavor grid (set of 2 or 3) 3063-S-2 3056-S-2 3064-S-3...
  • Page 6: Model Specifications

    MODEL SPECIFICATIONS MODEL SPECIFICATIONS TABLE Table 1 A430i A530i A540i A660i A790i Main burner quantity N/P orifi ce drill size #42 / #54 #40 / #53 #44 / #55 #42 / #54 #38 / #53 ▲ Backburner #52 / #59 #52 / #59 #48 / #56 #48 / #56...
  • Page 7: Substrate

    MODEL SPECIFICATIONS (cont.) SUBSTRATE When adding any substrate to the enclosure front wall (including tiles, stone, etc.), consider the following: Substrate Alongside Control Panel Substrate Behind Control Panel Substrate + countertop "front to back" cutout Any additional substrate alongside the control panel does not need to be considered in Dim.
  • Page 8: Built-In Grill Wiring Diagram

    MODEL SPECIFICATIONS (cont.) BUILT-IN GRILL WIRING DIAGRAM Oven Oven light Back burner igniter light (if equipped) Main burner igniters Wire harness assembly Wire harness extension Light switch Ground Main Main Main Back burner Meat probe wire burner 2 (if equipped) (if equipped) burner 3 burner 1...
  • Page 9: Grill Maintenance And Safety Information

    GRILL MAINTENANCE AND SAFETY INFORMATION 1. The outdoor grill and surrounding area MUST and clean the orifi ce and burner/venturi tubes remain clear of fl ammable substances such as for insects and insect nests. A clogged tube can gasoline, yard debris, wood, etc. lead to a fi...
  • Page 10: Installation Requirements

    INSTALLATION REQUIREMENTS Installation must be performed by a qualifi ed professional service technician. NON-COMBUSTIBLE This grill is designed for outdoor use only. DO NOT use this grill inside CONSTRUCTION ONLY a building, garage, enclosed area, or under overhead combustible Min. construction.
  • Page 11: Ensure Proper Combustion Air And Cooling Airflow

    INSTALLATION REQUIREMENTS (Cont.) The control panel MUST remain removable for servicing GAS-SUPPLY PLUMBING REQUIREMENTS (see PARTS LIST). For natural gas or a household propane system, rigid " ENSURE PROPER COMBUSTION AIR AND (1.3 cm) or " (1.9 cm) black steel pipe or local code- COOLING AIRFLOW approved pipe is required to conduct the gas supply to the unit.
  • Page 12: Enclosure Requirements

    ENCLOSURE REQUIREMENTS VENTILATION (ALL ENCLOSURES) Ventilation Requirements: For All Piping Systems and All Gas Types: • Minimum 4 openings (Natural Gas, Household Propane, L.P. Cylinder) (2 per side wall - spaced at 180 degrees) FOR YOUR SAFETY, you must provide the openings listed •...
  • Page 13: Propane Safety Information

    PROPANE SAFETY INFORMATION WHEN OPERATING THIS APPLIANCE WITH PROPANE, ALL INSTRUCTIONS AND WARNINGS MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION CAUSING SERIOUS INJURY OR DEATH. WARNING This gas appliance, its enclosure, and the propane cylinder enclosure, if any, MUST be plumbed and vented in accordance with local building and safety codes and should be approved by local code enforcement offi...
  • Page 14 UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE IMPORTANT POUR VOTRE SÛRETÉ LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE. En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements. LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.
  • Page 15: Safe Use & Maintenance Of Propane Gas Cylinders

    SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS IMPORTANT FOR YOUR SAFETY READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER. When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed. FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION. The use of pliers or a wrench should not be necessary.
  • Page 16: Installation Installation

    INSTALLATION INSTALLATION COUNTER PREPARATION Control panel Consult Table 1 for non-combustible enclosure cut-out stops here dimensions. An RHP insulating liner must be used if any supporting construction is combustible. Consult the instructions that come with the liner for dimensions and additional installation INCORRECT Countertop information before beginning the installation.
  • Page 17: Install The Flavor Grids

    INSTALLATION (Cont.) 4. Turn all burner control knobs to the OFF position. Turn the gas supply on. Then carefully check all gas Adjustable connections for leaks with a brush and half-soap/ support half-water solution before lighting. NEVER USE A screw MATCH OR OPEN FLAME TO TEST FOR LEAKS.
  • Page 18: Electrical Installation

    ELECTRICAL INSTALLATION POWER SUPPLY HOOKUP Required 120VAC (15 AMP minimum) GFCI CAUTION: IMPROPERLY CONNECTED WIRES WILL Required GROUNDED 3-wire receptacle (not included) CAUSE DAMAGE TO THE GRILL AND MAY GFI electrical receptacle RESULT IN PROPERTY DAMAGE AND/OR (not included) PERSONAL INJURY. This grill includes a power supply box.
  • Page 19: Identification Of Grill Controls

    USE, CARE, & SERVICE IDENTIFICATION OF GRILL CONTROLS Right Control panel main burner screw(s) control knob Backburner control knob Left (if equipped) main burner control knob Meat probe Drip (if equipped) Digital Thermometer tray Light switch (if equipped) Fig. 19-1 A430i and A530i controls Center main burner Control panel...
  • Page 20 ALLUMAGE DES INSTRUCTIONS (D’ALLUMAGE) Lisez toutes les instructions avant l’allumage, et suivez ces instructions chaque fois vous lumière le unité. ÉCLAIRAGE ÉLECTRONIQUE ÉCLAIRAGE MANUEL Note: Le unité doit être relié à la puissance 120VAC pour Note: L’éclairage électronique exige une batterie installée ATTENTION: Attendez toujours cinq (5) minutes le gaz l’éclairage électronique.
  • Page 21: Lighting (Ignition) Instructions

    LIGHTING (IGNITION) INSTRUCTIONS Read all instructions before lighting, and follow these instructions each time you light the unit. ELECTRONIC LIGHTING MANUAL LIGHTING Note: Electronic lighting requires an installed 9-volt Note: This unit must be connected to 120VAC power CAUTION: Always wait fi ve (5) minutes for gas to battery with a good charge.
  • Page 22: Optional Digital Thermometer

    OPTIONAL DIGITAL THERMOMETER Your grill comes with a digital thermometer for oven and meat probe temperature monitoring, and timed cooking. Pressing the power button will turn on the thermometer. The thermometer will automatically shut off after 5 minutes if no Meat probe handle temperature change is detected.
  • Page 23: Menu Screen

    OPTIONAL DIGITAL THERMOMETER (cont.) Set time as desired Setting the Timer 1. Press the timer button. Use the arrows to set the desired TIMER amount of time (see Fig. 23-1.) 05:00 2. Press SET to return to the default screen. Use arrows The time remaining will be shown on the default screen.
  • Page 24 OPTIONAL DIGITAL THERMOMETER (cont.) Setting the Alarm OVEN The alarm can be individually set (ON or OFF) for the meat PROBE probe and oven temp. The default setting has the alarm OFF Use arrows to select for the meat probe and oven temp. The alarm always alerts desired ®...
  • Page 25: Optional Rotisserie

    OPTIONAL ROTISSERIE CAUTION: WHEN USING THE BACKBURNER; KEEP Backburner cover Rotisserie THE OVEN LID CLOSED TO PREVENT HEAT rod bracket Warming rack LOSS, PROVIDE PROPER CONVECTION, AND PROVIDE PROPER VENTING. THIS WILL Rotisserie rod rear bracket ENSURE EVEN COOKING TEMPERATURES. Rotisserie DO NOT KEEP YOUR OVEN LID OPEN DURING motor...
  • Page 26: Optional Infrared Burner Operation

    OPTIONAL INFRARED BURNER OPERATION The infrared (IR) searing burner (optional) cooks with WARNING a powerful radiant heat. Only handle the infrared burner cover when the unit is cold or with a well-insulated long-handled tool or heat resistant gloves. Cover SIDE VIEW (with cover on) Ignitor Cut-out for NO foreign...
  • Page 27: Accessories

    ACCESSORIES GRILL BRUSH (optional) WARMING RACK (if equipped) ® Purchase a Fire Magic stainless-steel grill brush (sold The warming rack (Fig. 27-2) is packed separately. separately) to keep your grill cleaner. It comes with To install the warming rack, lift the front of the rack up scraper for large particles and a replaceable head with slightly and insert the rack hangers into the two holes brass bristles for overall cleaning.
  • Page 28: Fire Magic ® Drip Tray

    FIRE MAGIC DRIP TRAY ® The drip collector allows you to brush or scrape residue from the grill's inner liner into the drip tray . Following the manufacturers instructions and regular cleaning of the grill's interior with oven cleaner, will help to prevent grease fi res. Fig.
  • Page 29: Care & Cleaning

    CARE & CLEANING APPLIANCE MUST BE COMPLETELY COOL WHEN CLEANING. DO NOT SPRAY ANY CLEANER OR LIQUIDS ON THE APPLIANCE WHEN HOT. The appliance must be cleaned as often as once a month (depending on use) to prevent grease build-up and other food deposits.
  • Page 30: Replacing Halogen Bulbs

    REPLACING HALOGEN BULBS Your grill is engineered with the conveniences of 5. Wearing a pair of gloves, reach into the fi xture, electrical power for illuminating and igniting the grill. gently grab the bulb, and pull it straight out of the fi...
  • Page 31: Convert Gas Type / Check Burner Orifices

    CONVERT GAS TYPE / CHECK BURNER ORIFICES CAUTION: Make sure the grill is at a safe temperature CONVERT/CHECK MAIN BURNER ORIFICES and isolated from gas and electrical 1. Remove the cooking grid and fl avor grid from above supplies before beginning. the burner you are working on and set them aside.
  • Page 32 CONVERT GAS TYPE / CHECK BURNER ORIFICES (cont.) 4. Remove the access plate by pulling the bottom toward the front of the grill and rotating it upward and outward until the two top tabs attached to back wall of the oven can be removed from the slots in the top of the plate.
  • Page 33: Burner Air Shutter Adjustment

    BURNER AIR SHUTTER ADJUSTMENT AIR SHUTTER ADJUSTMENT 1. Follow the safety precautions and steps for main burner removal Important: Air shutters are preset at the Fig. 33-2 in the CHANGING factory based on the gas the grill is Adjustment THE MAIN BURNER built to burn.
  • Page 34 BURNER AIR SHUTTER ADJUSTMENT (Cont.) BACKBURNER (IF EQUIPPED) Too large an air shutter opening will allow too much air into the burner, which will cause the fl ames fi rst The air shutter is set at the factory. However, to shorten and then to appear to lift up off the ports. altitude or other local conditions may require air For the bottom of the fl...
  • Page 35: Control Panel Removal

    CONTROL PANEL REMOVAL To remove the control panel: 1. Turn the control knobs to the OFF position and turn off the gas supply to the unit. 2. Remove the drip tray . 3. Turn off the light switch and disconnect the power supply from the power source. 4.
  • Page 36: Notes Page

    NOTES PAGE Please use this page to record any information about your unit that you may want to have at hand.
  • Page 37: Troubleshooting

    TROUBLESHOOTING If you have trouble with the unit, please use this list to identify the problem. By trying one or more of the solutions to the possible cause, you should be able to solve the problem. If this list does not cover your present problem, or if you have other technical diffi...
  • Page 38: Warranty

    WARRANTY PETERSON FIRE MAGIC GRILLS AND ACCESSORIES LIMITED WARRANTY ® Robert H. Peterson Co. ("RHP") warrants your Fire Magic grill to be free from defects in material and workmanship. ® Fire Magic cast stainless-steel burners, stainless-steel rod cooking grids, and stainless-steel housings are warranted for as long as you own ®...

This manual is also suitable for:

Aurora a530iAurora a540iAurora a790iAurora a660i