Test Operation - Haier 1U18FS2ERA Service Manual

Hide thumbs Also See for 1U18FS2ERA:
Table of Contents

Advertisement

Operation
Timer On/Off On-Off Operation
1.After unit starts, select your desired operation mode.
2.Press TIMER button to change TIMER mode. Every
time the button is pressed, display changes as follows:
Remote controller:
0.5h
0.5h
TIMER ON TIMER OFF
TIMER ON-OFF
Then select your desired TIMER mode (TIMER ON or
TIMER OFF or TIMER ON-OFF). "
3.Press
/
button to set time.
Press the button for each time, setting time in the first
12 hours increased by 0.5 hour every time, after 12
hours,increased by 1 hour every time.
Press the button for each time, settiing time in the first
12 hours decreased by 0.5 hour every time, after 12
hours,decreased by 1 hour every time.
It can be adjusted within 24 hours.
4.Confirm timer setting
After adjust the time,press
time ON or OFF button will not flash any more.
5.Cancel timer setting
Press the timer button by times until the time display
eliminated.
Hints:
After replacing batteries or a power failure happens, time
setting should be reset.
According to the Time setting sequence of TIMER ON or
TIMER OFF, either Start-Stop or Stop-Start can be achieved.
HEALTH Operation
(This function is unavailable on some models.)
Press
button to enter additional options, when cycle
display to
,
will flash,and then press
health function. When cancel the function, please enter
additional options again and to cancel health function.
The anion
generator
in the airconditioner can generate
a lot of anion effectively balance the quantity of position
and anion in the air and also to kill bacteria and speed
up the dust sediment in the room and finally clean the
air in the room.
BLANK
0.5h
0.5h
TIMER OFF-ON
"or "
"will flash.
button and confirm the
,enter to
TURBO/QUIET Operation
(1)
TURBO Operation
When you need rapid heating or cooling, you can use this function.
Press TURBO button, the remote controller will show
and then achieve to the turbo function. Press again this
TURBO button , the turbo function will be cancelled.
(2)
QUIET Operation
Press
button to enter additional options, when cycle
display to
,
quiet function. When cancel the function, please enter
additional options again and to cancel quiet function.
Note
During TURBO operation, in rapid COOL mode , the room
will show inhomogeneous temperature distribution.
Long period QUIET operation will cause effect of not too
cool or not too warm.
Emergency operation and test operation
Emergency Operation:
Use this operation only when the remote controller
is defective or lost.
When the emergency operation switch is
pressed,the" Pi "sound is heard once, which means
the start of this operation.
In this operation, the system automatically selects
the operation modes,cooling or fan or heat,according
to the room temperature.
Room
Operation
mode
temperature
ABOVE 23
O
C
COOLING
BELOW 23
O
C
HEAT
(Cooling only uint
Room temperature
BELOW 23
O
C
It is not possible to operate in dry mode.

Test operation:

Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room
temperature is below 16
normal operation.
Continue to press the test operation
switch for more than 5 seconds. After
you hear the "Pi" sound twice,release
your finger from the switch: the cooling
operation starts with the air flow speed "Hi".
After 30 minutes, test operation ends automatically(Only for 22K,24K unit).
42
Parts and Functions
(This function is unavailable on some models.)
will flash,and then press
Designated
Timer
Air flow
temperature
mode
NO
26
O
C
AUTOMATIC
AUTOMATIC
NO
23
O
C
Timer
Operation
Designated
mode
mode
temperature
NO
FAN
26
O
C
o
C, do not use it in the
,
,enter to
Pi
Air flow
AUTOMATIC
Pi Pi

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

As18zs2era

Table of Contents