Advertisement
Quick Links
iNSTALLATiON
AND SERVICE MUST BE PERFORMED
BY
A QUALiFiED iNSTALLER.
iMPORTANT:
SAVE FOR LOCAL ELECTRICAL
INSPECTOR'S USE.
READ AND SAVE THESE iNSTRUCTiONS
FOR FUTURE REFERENCE.
This conversion
kit must be installed by a qualified
service
technician
in accordance
with the
manufacturer's
instructions and all applicable
codes and requirements of the authority
having jurisdiction.
Failure
to follow instructions may result in fire, explosion
or production
of carbon
monoxide
causing
property
damage,
personal
injury or loss of fife. The qualified
service agency is responsible for the proper installation ofthis
kit. The
installation is not proper and complete
until the operation
of the converted
appliance
is checked as specified in the
manufacturer's
instructions supplied with this kit.
Before proceeding
with the conversion,
shut off the gas supply before disconnecting
electrical power
to the range. Be sure both power supplies are off before installing the conversion
kit. Failure to do so could cause
serious bodily
injury.
Note: When surface burners are converted
from Natural
to L.P. the BTU ratings
become:
5,000 BTU* Natural
Gas to 4,500 BTU* LP. Gas
9,500 BTU* Natural
Gas to 8,000 BTU* L.P. Gas
12,000 BTU* Natural
Gas to 10,000 BTU* LP. Gas
17,200 BTU* Natural
Gas to 14,000 BTU* LP. Gas
L.P. Kit Contents
Kit pin 316243722 (wild berry)
Part Description
Part Number
Qty.
Surface Burner Orifice marked 0.68mm 4,500 BTU* (blue)
Surface Burner Orifice marked 0.89mm 8,000 BTU* (no color)
Surface Burner Orifice marked 0.95mm 10,000 BTU* (green)
Surface Burner Orifice marked 1.15mm 14,000 BTU* (black)
L.P. Kit Installation Instructions
316237907
316237906
316237905
316237910
316417516
1
1
1
1
1
*Note:
For
operation
at elevations
above
2000
ft.,
appliance
rating
shall
be reduced
at the rate
of 4 percent
for
each
1000
ft. above
sea
level,
How to Convert
the Range
for use with LP/
Propane
Gas
1.
Convert
the Pressure
Regulator
(complete this step
for ALL models):
To access the gas regulator, remove the storage drawer or Warmer Drawer.
If equipped with a storage drawer, open & removethedrawercompletely.
For
models equipped with a Warmer Drawer, foflow the instructions below to
remove the Warmer Drawer.
a.
_
Electrical
Shock Hazard can occur and result in
serious injury or death. Disconnect electrical power to the range before
removing the Warmer Drawer for servicing.
b.
Locate glide lever on each side of drawer, puff up on the left glide lever
and push down on the right glide lever (See Fig. 1).
c.
Pull the Warmer Drawer away from the range (See Fig. 2).
d.
Remove the regulator access cover if equipped.
Do not remove
the
Pressure
Regulator
or allow it to turn.
e.
Remove
the dust protector
from the cap (Gas models).
Use the
proper size wrench to remove the cap from the regulator(Aft
models).
f.
Follow the remaining instructions
provided in Fig. 3.
Tools
Required:
3/8", 1/2" and 5/8" Open End Wrench
1/8" Wide Flat Blade Screwdriver
7mm Nutddver
Pull up with finger
Left Glide
NOTE:
After replacing
the natural
gasto
LP orifices,
be sure to
keep the original
factory
installed
natural
gas orifices
for future
range conversion
back to natural
gas.
Push down with finger
Right Glide
Fig. 1
pin 316417516 (0711)
1
Advertisement
