Advertisement
Quick Links
iNSTALLATiON
A ND SERVICE MUST BE PERFORMED
BY
A QUALiFiED
iNSTALLER.
iMPORTANT:
SAVE FOR LOCAL ELECTRICAL
iNSPECTOR'S
USE.
READ AND SAVE THESE iNSTRUCTiONS
FOR FUTURE REFERENCE.
This conversion
kit must be installed by a qualified
service
technician
in accordance
with the
manufacturer's
instructions and all applicable
codes and requirements
of the authority
having jurisdiction.
Fail_
to follow instructions
may result in fire, explosion
or production
of carbon
monoxide
causing
property
damage
personal
injury or loss of life. The qualified
service
agency is responsible
for the proper installation of this kit.
installation is not proper and complete
until the operation
of the converted
appliance
is checked
as specified
in
manufacturer's
instructions supplied
with this kit.
Before proceeding
with the conversion,
shut off the gas supply before disconnecting
electrical
po_
to the range.
Be sure both power supplies
are off before installing the conversion
kit. Failure to do so could c_
serious bodily
injury.
Note: When surface
burners
are converted
from Natural to L.P. the BTU ratings become:
re
The
the
'er
use
5,000 BTU* Natural
Gas to 4,500 BTU* L.P. Gas
9,500 BTU* Natural
Gas to 8,000 BTU* L.P. Gas
12,000 BTU* Natural
Gas to 10,000 BTU* L.P. Gas
16,200 BTU* Natural
Gas to 14,000 BTU* L.P. Gas
L.P. Kit Contents
Kit pin 316467202 (yellow label)
Part Description
Part Number
Qty.
Surface Burner Orifice marked 0.68mm 4,500 BTU* (blue)
Surface Burner Orifice marked 0.89mm 8,000 BTU* (no color)
Surface Burner Orifice marked 0.95mm 10,000 BTU* (green)
Surface Burner Orifice marked 1.15mm 14,000BTU* (black)
L.P. Kit Installation Instructions
316237907
316237906
316237905
316237910
316417513
1
2
1
1
1
*NOTE:
For operation
at elevations
above 2000 ft., appliance
rating
shall
be reduced
at the rate of 4 percent
for each 1000 ft.
above sea level.
How to Convert
the Range for use with LP/
Propane
Gas
1.
Convertthe
Pressure
Regulator
To access the gas regulator,
remove the storage drawer or warmer
drawer. If equipped with a storage drawer, open & remove the drawer
completely.
For models equipped with a warmer drawer, follow the
instructions below to remove the warmer drawer.
a.
_
Electrical
Shock Hazard can occur and result
in serious injury or death. Disconnect
electrical
power to the
range before removing the warmer drawer for servicing.
b.
Locate glide lever on each side of drawer, pull up on the left glide
lever and push down on the right glide lever (See Fig. 1).
c.
Pull the warmer drawer away from the appliance (See Fig. 2).
d.
Remove the regulator access cover if equipped.
Do not remove
the pressure
regulator
or allow it to turn.
e.
Remove the dust protector from the cap. Use the proper size
wrench to remove the cap from the regulator.
f.
Follow the remaining instructions provided in Fig. 3.
NOTE:
After rep!aCing
the natural
gas to LP orifices; be sure to
keep the original
factory
installed
natural
gas orifices for future
range conversion
back to natural
gas.
Tools
Required:
3/8", 1/2" and 5/8" Open End Wrench
1/8" Wide Flat Blade Screwdriver
7mm Nutdriver
Pull up with finger
Left Glide
Right Glide
Push down with finger
Fig. 1
pin 316417513 (0705)
1
Advertisement
