Kenmore 796.91582410 Use & Care Manual page 5

SAFETY iNSTRUCTiONS FOR iNSTALLATiON
A WARN ING: To reduce the risk o fnre, eloctrlc shock, orinjory toparso.s when u sing this appliance,
follow basic precautions, including the following:
- Properly ground dryer to conform wffh all governing
codes and ordinances. Follow details in the installation
instructions.Electrical shock can result if the dryer is not
properly grounded.
"Before use, the dryer must be properly' installed as
described in this manual. Electrical shock can result if
the dryer is not properly grounded.
* Install and s_ore the dryer where it will not be exposed
to temperatures below freezing or exposed to
the weather.
oAff repairs and servicing must be performed by an
authorized service technician unless specificaffy
recommended in this Use & Care Guide. Use only
authorized factory parts. Failure to follow this warning
can cause serious injury, fire, electrical shock, or death.
• To ='educe the risk of electrical shock, do not install the
dryer in humid spaces. Failure to follow this warning
can cause serious injury, fire, electrical shock, or death.
* Conned to a properly rated, prefected, and sized
power ci_uit to avoid electrlcal overload. Improper
power circuits can melt, creating risk of electrical shock
and/or fire hazard.
* Remove all packing items and dispose of all shipping
materials properly. Failure to do so can result in death,
fire, explosion, burns, or death.
* Place dryer at least 18 inches above the floor for a
garage installation. Failure to do so can result in fire,
explosion, burns, or death.
=Keep all packaging from children. Packaging material
can be dangerous for children. There is a risk of
suffocation.
* Do nat install near items that produce heat or open
flame such as stoves or cooking ovens. Failure to follow
this warning can cause product deformation, smoke and
fire.
* Do not place candles or cigarettes on top of the
product. Failure to follow this warning can cause
product deformation, smoke and fire.
=Remove all protective vinyl film from the product.
Failure to do so can cause product deformation, smoke
and fire.
Exhaus|iDucfing:
* Gas dryers MUST be exhausted to the outside. Failure
to follow these instructionscan result in f_re or death.
* The dryer exhaust system must be exhausted to the
outside of the dweffing, if the dryer is not exhausted
outdoors, some fine lint and large amounts of
moisture wlll be expelled into the laundry area. An
accumulation of lint in any area of the home can
create a health and fire hazard.
• Use only rigid metaJ or Nexible metal 4 inch diameter
duct inside the dryer cabinet or for exhausting to the
outside. Use of plastic or other combustible dactwork
can cause a f_re. Punctured ductwork can cause a fire
if it collapses or becomes otherwise restricted in use or
during ins*.allation.
* Ductwork is riot provided with the dryer, and you
should obtain the necessary ductwork locally. The end
cap should have hinged dampers to prevent backdraff
when the dryer is not in use. Failure to follow these
instructionscan result in fire or death.
• The exhaust duct must be 4 inches (10.2 cm) in
diameter with no obstructions. The exhaust duct
should be kept as short as possible. Make sure to
clean any old ducts before installing your new dryer.
Failure to follow these instructionscan result in fire or
death.
• Rigid or semi rigid metal ductlng is recommended
for use between the dryer and the wall. In speclal
installations when it is impossible to make a
connection with the above recommendations, a UL
listed flexible metal transition duct may be used
between the dryer and wall connection only. The
use of this ductlng wlll affect drying time. Failure to
follow these instructionscan result in fire or death.
"DO NOT use sheet metal screws or other fasteners
which extend into the duct thai could catch lint and
reduce the efficiency of the exhaust system. Secure
all joints with duct tape. For complete details, follow
the Installation mnstructions.Failure to follow these
instructionscan result in fire or death.