Network Settings - Cisco TelePresence EX60 Administrator's Manual

Ex series
Hide thumbs Also See for TelePresence EX60:
Table of Contents

Advertisement

Cisco TelePresence System EX Series
Contents

Network settings

Network [1..1] IPStack
Select if the system should use IPv4, IPv6, or dual IP stack, on the network interface. noTE:
After changing this setting you may have to wait up to 30 seconds before it takes effect.
Requires user role: ADmIn
Value space: <Dual/IPv4/IPv6>
Dual: When set to Dual, the network interface can operate on both IP versions at the same
time, and can have both an IPv4 and an IPv6 address at the same time.
IPv4: When set to IPv4, the system will use IPv4 on the network interface.
IPv6: When set to IPv6, the system will use IPv6 on the network interface.
Network 1 IPStack: Dual
Example:
Network [1..1] IPv4 Assignment
Define how the system will obtain its IPv4 address, subnet mask and gateway address. This
setting only applies to systems on IPv4 networks.
Requires user role: ADmIn
Value space: <Static/DHCP>
Static: The addresses must be configured manually using the network IPv4 Address,
network IPv4 Gateway and network IPv4 Subnetmask settings (static addresses).
DHCP: The system addresses are automatically assigned by the DHCP server.
Network 1 IPv4 Assignment: DHCP
Example:
Network [1..1] IPv4 Address
Enter the static IPv4 network address for the system. This setting is only applicable when
network Assignment is set to Static.
Requires user role: ADmIn
Value space: <S: 0, 64>
Format: A valid IPv4 address.
Network 1 IPv4 Address: "192.0.2.2"
Example:
D14726.15 EX Series Administrator Guide TC7.2, AUGUST 2014.
Introduction
Web interface
System settings
System settings
Network [1..1] IPv4 Gateway
Define the IPv4 network gateway. This setting is only applicable when the network Assignment
is set to Static.
Requires user role: ADmIn
Value space: <S: 0, 64>
Format: A valid IPv4 address.
Network 1 IPv4 Gateway: "192.0.2.1"
Example:
Network [1..1] IPv4 SubnetMask
Define the IPv4 network subnet mask. This setting is only applicable when the network
Assignment is set to Static.
Requires user role: ADmIn
Value space: <S: 0, 64>
Format: The valid IPv4 address format.
Network 1 IPv4 SubnetMask: "255.255.255.0"
Example:
Network [1..1] IPv6 Assignment
Define how the system will obtain its IPv6 address and the default gateway address. This
setting only applies to systems on IPv6 networks.
Requires user role: ADmIn
Value space: <Static/DHCPv6/Autoconf>
Static: The codec and gateway IP addresses must be configured manually using the network
IPv6 Address and network IPv6 Gateway settings. The options, for example nTP and DnS
server addresses, must either be set manually or obtained from a DHCPv6 server. The
network IPv6 DHCPoptions setting determines which method to use.
DHCPv6: All IPv6 addresses, including options, will be obtained from a DHCPv6 server. See
rFC 3315 for a detailed description. The network IPv6 DHCPoptions setting will be ignored.
Autoconf: Enable IPv6 stateless autoconfiguration of the IPv6 network interface. See rFC
4862 for a detailed description. The options, for example nTP and DnS server addresses,
must either be set manually or obtained from a DHCPv6 server. The network IPv6
DHCPoptions setting determines which method to use.
Network 1 IPv6 Assignment: Autoconf
Example:
www.cisco.com — Copyright © 2010–2014 Cisco Systems, Inc. All rights reserved.
74
Administrator Guide
Setting passwords
Appendices

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Telepresence ex90Telepresence ex series

Table of Contents