GB
4.4 AUTOMATIC CONTROLS
LEVEL A ONLY
Introduction: the automatic controls make it possible to perform
cooking cycles in special modes and also to store cycles after
manual setting. For information on manual setting procedures
refer first to heading 4.3 MANUAL CONTROLS.
Note:
If the oven is switched off after you have set up a cooking cycle
manually the data you have entered will be lost since, in manual
mode, the controller does not store the cooking cycle.
To store manually set cooking programs for future use proceed
as described in the following headings.
The cooking cycles (or RECIPES) and programs (e.g. CLEAN)
are managed by means of the following commands:
Recipes or
programs ----------
Menu* ----------------
<
* list of commands (items) necessary for executing the various
management functions:
S 00
M E N U
S 06
A D D
P H A S E
S 03
S K I P
S 07
A D D
D E L A Y
S 09
C L E A R
S 17
C O N F I R M
S 18
R E T U R N
S 10
C L E A R
S 17
C O N F I R M
S 18
R E T U R N
S 11
M E M O R I Z E
S 13
S E L E C T
S 02
C O N F I R M
S 14
E D I T
S 02
C O N F I R M
S 15
S A V E
S 16
R E T U R N
S 04
S E A R C H
S 01
C O N F I R M
S 05
S E A R C H
S 12
E X I T
S 17
C O N F I R M
S 18
R E T U R N
S 19
P A S S W O R D
S 20
N E W
P A S S W O R D
S 21
C O N F I R M
S 22
C H A N G E
P (Program) =
button to:
- open the list of recipes and programs
- open the menu of recipes or programs
- confirm the items selected from the menus
(^) (v)
= "arrow" buttons (up and down)
(or use the knob) to:
- select recipes, programs or relative names
- select menu items
- select the utilities
- set the values
(<) (>)
=
"arrow" buttons (left and right) to:
- return to menu
- select the phases
DISPLAY
=
displays the operations
described above
DISPLAY
^
>
v
P H A S E
P H A S E
R E C I P E
R E C I P E
N U M B E R
N A M E
R E C I P E
B Y
N A M E
B Y
N U M B E R
P A S S W O R D
P A S S W O R D
4.4.1 AUTOMATIC SEQUENTIAL MULTIPHASE COOKING
Food can be cooked using different temperatures during the
cooking cycle (i.e. in several different stages).
The LEVEL A oven allows the execution of programs composed
of several sequential phases. For example:
- Phase 1:
- air-convection cycle 200°C
- core probe 70°C
- Phase 2:
- mixed cycle 220°C
- time 40 minutes
- Phase 3:
- air-convection cycle 250°C
- time 15 minutes
and so on up to a maximum of 7 phases.
During the cooking cycle the oven advances from one phase to
the next one automatically until the cooking program is completed
and then stops automatically as soon as the last phase has been
terminated.
To set a multiple phase cooking program proceed as follows:
1) Switch on the oven.
2) Set (see heading 4.3 MANUAL CONTROLS):
- cooking mode for phase 1;
- oven chamber temperature for phase 1;
- cooking time (or core probe temperature) for phase 1.
3) Press button P and the DISPLAY will show the flashing value
1 (phase 1) and the description P:MENU.
4) Press button P to open the menu, the option P:ADD PHASE
appears on the DISPLAY (it is also possible to select another
option from the menu).
phase 1 flashing
1
selected item
P : A DD
5) Press button P to confirm this option; the DISPLAY will now
show a flashing number 2 (phase 2) and some of the MANUAL
CONTROL functions will start flashing.
phase 2 flashing
1 2
selected item
P : ME NU
6) Set new values, as described in point 2), but this time with
reference to phase 2.
7) To set additional phases repeat steps 4, 5 and 6 up to a
maximum of 7 phases.
8) The multiple phase cooking program has now been set up.
Place the product to be cooked in the oven and press the Start
cycle button.
The cooking cycle will start from phase 1 (value 1 flashes in
alternation with a dot on the relative DISPLAY) and, when phase
1 is terminated, it will advance automatically to phase 2 (value
2 flashes in alternation with a dot on the relative DISPLAY) and
so on until all set phases are completed.
phase 2 in progess
1 2
The transition from one phase to the next is signalled by a short
audible signal.
When the last phase is terminated the cooking cycle will stop
automatically as already described, and the appliance will emit a
double intermittent audible signal.
To repeat the same multiple phase cycle simply press the START/
STOP button again.
While the cooking cycle is in progress you can skip one or more
of the phases as follows:
- press the (>) button one or more times to select the successive
phases.
- press button P once and then press it again at the "SKIP PHASE"
option to confirm the selected phase and cause it to start.
40
PH A SE