Battery; Replacement Battery Specifications; Invalid Battery Error Message; Charging Options - Honeywell Dolphin 75e User Manual

Hide thumbs Also See for Dolphin 75e:
Table of Contents

Advertisement

Battery

The primary power source for the Dolphin terminal is the 3.7V Li-ion rechargeable battery located under the battery door on the
back panel of the device. Honeywell recommends, you keep the battery in the terminal charged at all times to help prevent data
loss. Letting the battery become fully discharged causes the terminal to lose all data in RAM.
Note: All data in RAM is cleared when the battery is removed. Always power off the terminal before removing the battery to
ensure any changes made are saved to the flash memory.

Replacement Battery Specifications

Dolphin 75e model terminals are designed for use with battery part numbers BAT-STANDARD-02 (Li-ion 3.7V, 6.179 watt
hour) and BAT-EXTENDED-02 (Li-ion 3.7V, 12.358 watt hour) manufactured for Honeywell International Inc. For information
on how to replace the battery, see page 1-11.
Important Battery and Battery Door Replacement Guidelines
Follow the guidelines listed below when ordering batteries and/or battery doors.
• Size (e.g., standard or extended): The battery and battery door must be the same size.
• Type (e.g., locking or non-locking): Dolphin 75e models are only compatible locking type battery doors.
• Near Field Communication (NFC) requirements: Use only NFC compatible battery doors with NFC equipped Dolphin
models identified with the letter N at the end of the model number (e.g., 75exxN).
We recommend use of Honeywell Li-ion battery packs. Use of any non-Honeywell battery may result in damage
not covered by the warranty.
Important: All battery and connector doors must be present, undamaged, and properly closed to maintain the
environmental rating of the terminal.

Invalid Battery Error Message

If the terminal displays an invalid battery error message, replace the battery with a qualified Honeywell Li-ion battery pack.

Charging Options

Dolphin 75e terminals ship with the battery significantly discharged of power. Before using a terminal for the first time,
charge the battery with a Dolphin charging device for a minimum of 4 hours for the standard battery and 6 hours for the
extended battery. When using the 70e-USB Charge/Communication cable to charge from a 500mA USB port on a host
device, charge the battery for a minimum of 6 hours for the standard battery and 8 hours for the extended battery.
When the main battery is installed in the terminal, use one of the following:
Dolphin 70e Black HomeBase (Model
Dolphin 70e Black eBase (Model
Dolphin 70e Black Mobile Base (Model
Dolphin 70e Black ChargeBase (Model
Dolphin 70e Black Net Base (Model
• Dolphin 70e USB Charge/Communication Cable (Model 70e-USB ADAPTERKIT) included with terminal,
When the main battery is not installed in the terminal:
• Place the battery pack in the
70e Black eBase (Model
• Insert the battery in the QuadCharger (Model COMMON-QC),

Charging Times

Charging Peripheral/Accessory
HomeBase (Model 70e-HB)
eBase (Model 70e-EHB)
70e-HB), see page
70e-EHB), see page
70e-MB), see page
70e-CB), see page
70e-NB), see page
Auxiliary Battery Well
of the
70e-EHB).
8-1
9-1
10-1
11-1
12-1
Dolphin 70e Black HomeBase (Model 70e-HB)
see page
2-1.
Model: 70e-BTSC
BAT-STANDARD-02
4 hours
4 hours
see page 1-3
or the
Dolphin
Model: 70e-BTEC
BAT-EXTENDED-02
6 hours
6 hours
2 - 9

Advertisement

Table of Contents
loading

Table of Contents