§1 Warranty MUTEC GmbH warrants the flawless performance of this product to the original buyer for a period of two (2) years from the date of purchase. If any failure occurs within the specified warranty period that is caused by defects in material and/or workmanship, MUTEC GmbH shall either repair or replace the product free of charge within 90 days.
We ask you to be so kind to register This all makes MC-6 for sure a unique and the most flexible digital audio your MUTEC product through our website format converter in a 9.5“ case currently available in the market! immediately after purchasing.
Always be sure to connect the Word Clock output of the MC-6 We recommend using high-grade cables with to the corresponding input of the device you wish to synchronize. Cable a good shielding.
Page 12
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Additionally, you should make sure that the Word Clock input to be con- nected to the MC-6’s output have a 75 Ω terminating resistor! Most Word Clock inputs allow for enabling/disabling the termination with a so-called »termination-switch«, which may be located on the outside or inside of the...
« are for control of the MC-6‘s operation status only. They are not accessable for adjustments. General Operation Procedure The menu of your MC-6 is strictly organized aligned to general handling Continuous Clock Supply procedures when inserting the MC-6 into your studio‘s data stream. Thus,...
AES3 output. Thus, the original input signal is not lost and available sion without SRC into AES3id and S/P-DIF, for further use! the MC-6 needs to derive a valid clock signal Under »REFERENCE« the »AES3« option is selected automatically. Please see from the incoming audio source. Therefore, the grey box on the left hand side for more information.
»AES3«) simultaneously to all available output formats. The sampling rate of all outputs now depends on the clock rate of the reference clock signal, Your MC-6 is able to lock to so- which is selected in the »REFERENCE« menu. The above example shows called »Super Clock«...
AUDIO REFERENCE This is a special function of your MC-6! It allows e.g. to receive an AES3 signal and an AES3id signal simultaneously. The AES3 input signal is conver- ted to AES3id and the AES3id input signal is converted to AES3. The other digital audio outputs are shut down.
\\\\\\\\\\\\\\\\\\ A N H A N G A N H A N G A N H A N G > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Bidirectional Format and Sampling Rate Conversion 32.0 UNI-DIR...
MODE AUDIO REFERENCE This setting is a very special and of course unique function of your MC-6! The function allows to convert two digital audio signals at the same time, whereas both conversion streams may consist of different sampling rates.
AUDIO REFERENCE X-SRC Mode between S/P-DIF optical and S/P-DIF coaxial. STATUS This area displays different system conditions of your MC-6. There is no access for changing settings. »LOCK« (2 x ) Doing unidirectional format and sampling rate conversions, the first »LOCK«...
Page 22
\\\\\\\\\\\\\\\\\\ A N H A N G A N H A N G A N H A N G > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > X-SRC Mode: The sampling rate of the digital audio format, selected as first in the »AUDIO...
= Termination When moving the jumper from position 1 to position 2, the input termi- nation will be switched-off. Therefore, the MC-6 must be connected in a chain, in which a device with terminated input follows. Otherwise you need to use a BNC-T piece in combination with a 75 Ω BNC resistor for terminat- ing the MC-6’s input.
Page 25
\\\\\\\\\\\\ AP P E N D I X AP P E N D I X AP P E N D I X > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > AES11 REFERENCE INPUT 1 x XLR female, transformer balanced, input impedance 110 Ω, 200 mV –...