Denon AVR-X4100W Service Manual page 94

Error
DPMS Update Error Display
Code
S u b
5B
U p d a t i n g
S u b
5C
U p d a t i n g
S u b
5D
U p d a t i n g
S u b
5E
U p d a t i n g
S u b
5F
U p d a t i n g
S u b
60
U p d a t i n g
S u b
61
U p d a t e C h e c k N G
S u b
62
U p d a t i n g
G U I
80
U p d a t i n g
G U I
81
U p d a t i n g
G U I
82
U p d a t i n g
G U I
83
U p d a t i n g
G U I
84
U p d a t i n g
G U I
85
U p d a t i n g
G U I
86
U p d a t i n g
E t h e r I M G
A0
C o n n e c t i o n F a i l A 0
NACK received in response or no
* * * m i n
response from Sub for L com-
f a i l 5 B
mand.
* * * m i n
No Update Packet received from
CX870 / CY920 (Time Out).
f a i l 5 C
Abnormal data in Update Packet
* * * m i n
received from CX870 / CY920
f a i l 5 D
(CRCError).
Abnormal data in Update Packet
* * * m i n
received from CX870 / CY920
f a i l 5 E
(PacketNoError).
* * * m i n
Setup failure of the transfer meth-
od of XModem.
f a i l 5 F
NACK received in response or no
* * * m i n
response from Sub for "P" com-
f a i l 6 0
mand.
Mismatched Check Sum in re-
* * * m i n
sponse or no response from Sub
6 1
for I command.
* * * m i n
Failed to start up Sub in Power On
sequence during Update.
f a i l 6 2
Write Enable Latch Bit not set in
* * * m i n
Read after issuing WREN com-
f a i l 8 0
mand.
* * * m i n
Block Erase failed in Read after
issuing BE command.
f a i l 8 1
* * * m i n
No Update Packet received from
CX870 / CY920 (Time Out).
f a i l 8 2
Abnormal data in Update Packet
* * * m i n
received from CX870 / CY920
f a i l 8 3
(CRCError).
Abnormal data in Update Packet
* * * m i n
received from CX870 / CY920
f a i l 8 4
(PacketNoError).
* * * m i n
Setup failure of the transfer meth-
od of XModem.
f a i l 8 5
* * * m i n Mismatched Check Sum in Check
Sum comparison after rewriting.
f a i l 8 6
* * * m i n
IP Address acquisition failure
(AutoIP).
94
Details of Error code Coping strategies
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Turn on the power again. Update will
start automatically.
Check the network connection. Update
in an environment where there is a
small network load.