Function Descriptions
[11] Privacy Mask Settings
Display Area: Aspect Ratio 16:9 (4:3)
0x000
(0x000)
0x000(0x000)
0x1DC(0x312)
0x25C(0x39E)
0x438(0x6B0)
*Area initially displayed using the Area Mask ON
command.
Notes:
Up to 8 mask can be displayed within one view angle.
When module is mounted on Pan Tilt Dome Camera,
PAN/TILT Angle info must be sent to the module
camera in advance.
To hide the masked subject more precisely, update
the PAN/TILT angle info within the interval of less than
75 msec.
Setting the Mask Position (Area Mask Position Set)
Command: A0 10 09 0p 0q 0r 0s 0t 0u 0v 0w 0x 0y
0z 0a 0b 0c 0d e f g CS FF
Parameter:
p
Aspect Ratio ( 0: 16:9
q
Mask Number (No. 1-15)
rst
x-Coordinate Start Position
uvw
y-Coordinate Start Position
xyz
x-Coordinate End Position
abc
y-Coordinate End Position
d
Mask transparency (0 - 15)
efg
Y ( 0 - 127 ) Pb ( 0 - 127 ) Pr ( 0 - 127 )
*Query Command Mask Position responds in the
same parameter as described above.
Usage: Sets the position of the specified mask numbers.
Y coordinate
start point
Y coordinate
end point
y
0x38D
0x3F3
0x780
(0x43C)
(0x4B4)
(0x8F0)
1: 4:3 )
X coordinate
end point
X coordinate
start point
x
The upper left and lower right horizontal and vertical
coordinates (12 bits each) are each divided into 4 bits
each.
Example) Setting the mask position according to the
following parameters
Aspect Ratio
Mask Number
x-Coordinate Start Position
y-Coordinate Start Position
x-Coordinate End Position
y-Coordinate End Position
Mask transparency
Y/Pb/Pr
Pan Angle*
Tilt Angle*
*For PAN Angle and TILT Angle, the angle parameters
that were sent in advance to the camera by PAN/TILT
Degree Command will be reflected automatically.
Setting Procedures
1. Mask Position (x, y coordinates) , Mask
transparency and Mask color Settings
(Area Mask Position Set)
A0 10 09 01 01 01 0F 04 00 0C 08
04 0B 00 01 0F 04 01 40 40 40
CS FF
2. Setting Mask ON (Area Mask ON)
A0 10 01 01 CS FF
< Color Setting(Y/Pb/Pr) >
Black
0x00/0x40/0x40
Gray
0x40/0x40/0x40
White
0x7F/0x40/0x40
Red
0x29/0x2D/0xF0
Blue
0x14/0x78/0x37
Note: Set the mask size to sufficiently cover the mask
object. The system will save the coordinates
after calculating out the coordinates at the
Wide-End against the current zoom ratio.
Settings Increasing Privacy Mask Accuracy
Area Mask Position Center Set
Command: A0 10 0A 0p 0q 0r 0s 0t 0u 0v 0w
0x y z a CS FF
Parameter:
p
Aspect Ratio ( 0: 16:9 1: 4:3 )
q
Mask Number (No. 1-15)
rst
Mask Width
uvw
Mask Height
x
Mask transparency
yza
Y/Pb/Pr
−27−
1(4:3)
1
0x1F4
0x0C8
0x4B0
0x1F4
1
0x40 / 0x40 / 0x40
135°
45°