Stichwortverzeichnis
A
Abreißblech ............................................................. 13
Abwickler Transferfolie ............................................ 47
Aktualisierung der Firmware ............. 24, 28, 30, 53, 59
Andrucksystem .................................................. 12, 44
Anschlussspannung, Weitbereichsnetzteil ............... 17
Arbeitsspeicher ........................................................ 15
Auflösung und Heizpunktanzahl ............. 14, 26, 28, 40
Aufwickler, intern ................................ 9, 11, 15, 46, 66
Aufwickler Transferfolie ........................................... 47
Ausdruck Geräteliste ......................................... 17, 26
Ausfall von Gerätefunktionen ................................... 82
Ausrichtung des Druckkopfes .................................. 72
Austausch der Druckwalze ...................................... 44
Austausch der Umlenkwalze ................................... 44
B
Barcodes ................................................................. 17
Baugruppen, Wechsel ............................................. 39
Belegungsplan ............................................... Anlage D
Betriebsspannung .................................................... 17
Blockschaltbild ............................................... Anlage B
C
cab-Adresse .............................................................. 5
CABLABEL .......................................................... 5, 10
CompactFlash-Karte ................................ 15, 19, 26, 30
D
Daten Druckkopf .......................................... 14, 26, 40
Datum .......................................................... 15, 24, 28
Deckel ..................................................................... 11
Deckel A3/A4/A6, Demontage ................................. 39
Druckbildinhalte ....................................................... 16
Druckerkonfiguration .................. 19, 20, 22, 24, 34, 51
Druckkopf, Ausrichtung ........................................... 72
Druckkopf, Reinigung .............................................. 35
Druckkopf, Wechsel ................................................ 40
Druckkopfabstützung ................................... 12, 44, 75
Druckkopfandruck ................................................... 73
Druckkopfbombierung ............................................. 74
Druckkopfprofil .................................................. 17, 23
Druckmechanik ................................................. 11, 12
Druckmechanik, Einstellelemente ............................ 72
Druckmechanik, Justage ......................................... 75
Druckparameter ....................................................... 21
Druckwalze .............................................................. 12
Druckwalze, Austausch ........................................... 44
Druckwalze, Reinigung ............................................ 36
E
Einstellung Kupplung interner Aufwickler ................. 66
Einstellung Kupplung Transferfolienabwickler ......... 66
Einstellung Kupplung Transferfolienaufwickler ........ 66
Einstellung Kupplung Etikettenabwickler A8 ............ 66
Ereignisliste ................................................. 19, 23, 28
Ersatzteile ............................................................... A-1
Ethernet-Schnittstelle ........... 10, 13, 16, 20, 22, 25, 27
Serviceanleitung / Service Manual
Index
A
Adjusting the belt tension ......................................... 78
Adjusting the hub torques ........................................ 66
Adjustment of the print mechanism ......................... 72
Adjustments ............................................................ 66
Alignment of the printhead ....................................... 72
ASCII dump mode ....................................... 17, 23, 81
Assembly units, replacement ................................... 39
B
Barcodes ................................................................. 17
Belt tension .............................................................. 78
Block diagram ............................................ Appendix B
C
cab address ............................................................... 5
CF card ................................................... 15, 19, 26, 30
CABLABEL .......................................................... 5, 10
Cleaning, general .................................................... 35
Cleaning the label edge sensor ............................... 36
Cleaning the printhead ............................................. 35
Cleaning the print roller ............................................ 36
Clear service counters ....................................... 19, 30
Cover ....................................................................... 11
Cover, removal ........................................................ 39
CPU PCB, replacement ........................................... 51
D
Date ............................................................. 15, 24, 28
Device list .......................................................... 17, 26
Device types .............................................................. 9
Dispense plate ................................................... 10, 12
E
Environmental conditions ......................................... 17
Errors during printing ............................................... 80
Ethernet interface ................. 10, 13, 16, 20, 22, 25, 27
Event log ..................................................... 19, 23, 28
F
Failure of device functions ....................................... 82
Features .............................................................. 8, 10
Firmware updates ............................. 24, 28, 30, 53, 59
FlashCard ................................................ 15, 19, 26, 30
Font list .............................................................. 17, 23
Fonts ....................................................................... 16
Functions for servicing ............................................. 19
G
Graphics ............................................................ 16, 17
H
Hardware fault ................................................... 28, 84
Head switch ............................................................. 79
Hub torques, adjustment ......................................... 66
Hub, transfer ribbon ..................................... 11, 46, 66
/
/
/
I-1