User& Set-Upinstructions; Generaluser Information; Control Set-Up Procedures; Start Operating Set-Up - Maytag MHN31PDAWW Installation Instructions Manual

USER& SET-UPiNSTRUCTiONS
WHITES COLORS BRIGHTS
PERM. WOOLENS DEMCATES
PRESS AND KNITS
NOTE: After the washer has been installed and plugged in, the
display may show '0 MINUTES'. Once the washer has been
plugged in and the washer door opened and closed, the display
will show the price. In washers set to $0.00 vend price, the
display will flash 'SELECT CYCLE' instead of a vend price. Note,
however, that the PR models will require a Smart Card to enable
a cycle.
1. PD Models: Insert coins until 'SELECT CYCLE' flashes in
display.
PR Models: A debit card is required rather than coins. In
Enhanced Debit mode, the card balance will also display
when a debit card is inserted into the reader.
2. Door must be closed before cycle selection is made,
3. Press fabric setting button for the wash cycle desired. After
the cycle is started, the time will display and count down.
4. If a cycle is interrupted by opening the door, 'RESELECT
CYCLE' will flash in the display. To restart the washer, close
door, and reslect desired cycle.
GeneralUser Information
SCROLLING 'OUT OF ORDER' SHOWING IN DISPLAY
This condition indicates the washer is inoperative.
'0 MINUTES' SHOWING IN DISPLAY
This indicates the cycle is complete and the washer cannot be
operated. Coins dropped or debit inputs during this condition will
be stored in escrow but cannot be used until normal operation is
restored by opening and closing the door. If a door switch fails, it
must be replaced before normal operation can be restored.
COLD START (initial first use)
Washer is programmed at the factory as follows:
11 -minute wash period
3 rinses (extra rinse not enabled)
7 x coin 1 wash price (PD models)
WARM START (after power failure)
A few seconds after power is restored, if a cycle was in progress at
the time of the power failure, 'RESELECT CYCLE' will flash in the
display, indicating the need for a key press to restart washer.
DOOR LOCK
Prior to beginning a cycle, there is a door lock routine of lock/unlock/
relock then cycle begins. The door will remain locked until the end of
a cycle or approximately 2 minutes after a power interruption.
PRICING
After the door is opened following the completion of a cycle, the
display indicates the cycle price (unless set to $0.00 Vend). As
coins are dropped or debit inputs arrive, the display will change to
lead the user through the initiation of a cycle.
FREE CYCLES
The PR models require a valid form of payment (or vend) to start a
cycle, even if the amount is set at $0.00 (see $0.00 Vend below).
$0.00 VEND
The PR models require a valid form of payment (or vend) to start a
cycle, even if the amount is set at $0.00.
In this mode, the washer must be equipped with a debit card reader
and the cycle price set to $0.00. The user must have a valid Smart
Card to start a cycle, although no value will be deducted from
the card.
DEBIT CARD READY
This washer is debit card 'cable' ready. It will accept a variety of
debit card systems, but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper washer
set-up. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
DISPLAY
After the washer has been installed and plugged in, the display
may show '0 MINUTES'. Once the washer has been plugged in
and the washer door opened and closed, the display will show
the vend price. In washers set for $0.00 Vend, the display will
flash 'SELECT CYCLE' and the PR Model will require a Smart
Card to enable a cycle.
ControJ Set-up Procedures
IMPORTANT: Read all instructions before operating.
PD Models: insert access door key, turn, and lift to remove access
door.
PR Models: Once the debit card reader is installed (according
to the reader manufacturer's instructions), the set-up mode can
only be entered by inserting a set-up card (supplied by the reader
manufacturer) into the card slot.
The lower fabric setting buttons and the digital display are used to
set up the controls.
The display can contain 4 numbers and/or letters and a decimal
point. These are used to indicate the set-up codes and related
code values available for use in programming the washer.
HOW TO USE THE BUTTONS TO PROGRAM THE CONTROLS
1. The PERM PRESS button is used to adjust the values
associated with set-up codes. Pressing the button will change
the value by increments. Rapid adjustment is possible by
holding the button down.
2. The WOOLENS button will advance through the set-up codes.
Pressing the button will advance to the next available set-up
code. Holding the button down will automatically advance
through the set-up codes at a rate of 1 per second.
3. The DELICATES AND KNITS button is used to select or
deselect options.
Start Operating Set-up
Washers are preset at the factory for an 11 -minute wash period
and 3 rinses (no extra rinse).
SET-UP CODES
[] The WOOLENS button will advance you from code to code.
[] The PERM PRESS button will change the code value.
[] The DELICATES AND KNITS button will select or deselect
options.
FOR PR MODELS: The set-up codes are the same as for the
"PD" model except where noted.
The set-up code is indicated by the one or two left-hand
characters. The set-up code value is indicated by the two or
three right-hand characters.
10