Maintenance - Black & Decker BDV012I User Manual

When the vehicle starts, turn the unit's ON/OFF switch (7)
to the OFF position.
Leave the vehicle's engine running.
Disconnect the (-) black clamp connected to the engine or
chassis first, followed by the (+) red clamp that is connected
to the battery positive (+) terminal.
Carefully press the negative (black) jumper cable wire into
the storage channel starting at the end furthest from the
clamp.
Clamp the negative (black) clamp onto the clamp holder
(14).
Carefully press the positive (red) jumper cable wire into the
storage channel starting at the end furthest from the clamp.
Clamp the positive (red) clamp onto the clamp holder(14).
Charge the unit as soon as possible.
Using the inflator (fig. C)
Warning! When using the inflator:
Do not direct the nozzle at animals or bystanders.
Never leave the compressor unattended when running.
Only use the adaptors supplied.
Should the unit run over an extended period of time it may
overheat and cause the thermal trip to activate. When this
occurs switch the compressor off and allow to cool for
30 minutes.
Keep the compressor stored out of reach of small children.
The gauge is intended as a guide only. Tyre pressures
should be regularly checked with a certified gauge.
Do not over inflate any object as this may cause a risk of
injury.
This inflator can be used to inflate car tyres and sports
equipment.
Remove the inflator hose from the storage compartment.
If an adaptor is required, choose the correct adaptor (18) for
the product you are inflating and fit it into the nozzle (15).
Fit the nozzle (15) of the inflator or the adaptor (18), if fitted,
to the valve of the item to be inflated. Make sure that the
nozzle (15) is locked in place.
Move the inflator switch (16) to the on position (I).
Monitor the pressure gauge (17) until the required pressure
is reached.
Move the inflator switch (16) to the off position (0).
Remove the adaptor (18), if fitted, or the nozzle (15) from
the inflated item.
Remove the adaptor (18), if fitted, and store it in a safe
place and return the hose to the storage compartment.
Using the 12 Vdc portable power supply (fig. A)
This portable power supply can be used with all 12 Vdc
accessories equipped with a male accessory outlet plug
rated up to 5 amps.
6
Warning! Do not attempt to use or charge the unit while the 12
Vdc accessory outlet (3) is in use.
Lift the cover of the 12 Vdc accessory outlet (3).
Insert the 12 Vdc plug from the appliance into the 12 Vdc
accessory outlet (3) on the top of the unit.
Warning! Do not exceed a 5A load.
Switch on the appliance and operate as usual.
Periodically press the battery status pushbutton (4) to
check the status of the internal battery.
Warning! Make sure that the unit's ON/OFF switch (7) is in the
OFF position when using the unit's 12 Vdc accessory outlet (3).
Warning! Do not operate appliances that draw more than 5
amps.
Warning! Never insert a cigarette lighter into the 12 Vdc
accessory outlet (3).
Using the LED area light (fig. A)
The LED area light (10) will operate up to 114 hours on a full
charge. The LED area light's operating life is 100,000 hours.
Slide the LED area light on/off button (8) on the top panel of
the unit to turn the LED area light (10) on.
Slide the LED area light on/off button (8) on the top panel of
the unit to turn the LED area light (10) off.
Make sure that the LED area light is turned off while the unit
is being charged or stored.

Maintenance

Your Black & Decker tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth. Do
not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
Replacing the fuse in the vehicle dc power cord
Remove the gold cap by turning it counter clockwise.
Remove the rubber washer, centre pin and the spring.
Remove the fuse.
Fit a new fuse of the same type and size (8 A).
Install the centre pin, spring and rubber washer.
Install the gold cap by turning clockwise onto the plug.