Test Mode - Sony SCD-C222ES Service Manual

This set automatically executes self-diagnosis and various checks
by entering the test mode.
Note: This set automatically makes various adjustments according to the
type of disc, thereby not requiring adjustment of the set when parts
were replaced. However, be sure to execute 5-1. IC AND FLUO-
RESCENT DISPLAY TUBE CHECK, 5-2. AUTO CHECK and 5-
8. WAVEFORMS CHECK.
Disc for Test Mode
Various checks of this set require the following discs.
Model Type *1 Category
MODEL
SATD-S5
12 cm disc
(J-2501-215-A) SL
Reference disc
SATD-S4
(J-2501-184-A)
Not specified DL 12 cm disc
PATD-012
(4-225-203-01) 12 cm disc
CD
YEDS-18 Reference disc
(3-702-101-01)
Not specified HYBRID 12 cm disc
*1 SL: Single Layer
DL: Dual Layer
Setting Method of Test Mode
[POWER]
Turn the switch on while pressing the
[MENU]
dial and the button. Release the
[ AMS ]
l L dial in this order when "Test Mode Menu" is
displayed on the fluorescent indicator tube. (If the
dial is released first, the test mode becomes active but "Test Mode
Menu" is not displayed)
Test Mode Command List
The contents of test mode are as follows.
Note: Wrong operation in the test mode causes a trouble, thus requiring extreme care.
LINE command (1X): Use mainly for a manufacturing line.
No. Name Description
05 DSP MON1 XUGF, XPCK, C2PO outputted from IC509 (CD DSP)
06 DSP MON2 MNT0, MNT1, MNT2, MNT3 outputted from IC509 (CD DSP)
07 DSP MON3 RFCK, XPCK, XROF, GTOP outputted from IC509 (CD DSP)
STANDARD command (1X): Use when the servo is applied by manual operation.
No. Name Description
12 LD ON/OFF The laser diode is turned on or off
13 SPIN ON/OFF The spindle motor is rotated with the regulated voltage
14 FSRV ON/OFF The focus servo is turned on or off
15 TSRV ON/OFF The tracking servo is turned on or off
16 CLV ON/OFF The spindle SLV servo is turned on or off
Focus and tracking servos must be already turned on
17 SSRV ON/OFF The sled servo is turned on or off
Focus, tracking and spindle servos must be already turned on
18 ALL SRV ON All servos are turned on
19 ALL SRV OFF All servos are turned off
SECTION 5

TEST MODE

Application
Adjusted value check,
Operation check,
Optical waveform check
Operation check
Adjusted value check,
Operation check,
Optical waveform check
Operation check
[ AMS ]
l L
[MENU]
button and the
[ AMS ]
l L
[ OPEN/CLOSE]
Key in the Test Mode.
A
[ OPEN/CLOSE]
The A key is disabled immediately after setting
the test mode. Be sure to turn the
[ AMS
Table Init and push l L
table is completed, the message "INITAIL OK" appears several sec-
onds on the fluorescent indicator tube. After this, the
CLOSE]
key is enabled and disc can be inserted and ejected.
When the command 59 Table Init is executed, the same operations
of the POWER ON to the disc chucking in the normal operations
as described below are performed. However, it presumes that the
door and the tray are closed depending on the stop status.
59 Table Init t BU DOWN (disc unchucking)
(disc search) t BU UP (disc chucking) at the disc that is found
first of all.
When there are no discs, BU UP is executed at the DISC1 posi-
tion.
Releasing Method of Test Mode
To release the test mode, turn the
Selection/Entry of Test Mode
To select and enter the "Test Mode Menu", operate as follows.
[ AMS
1. Rotate the l L
[ AMS ]
the dial to enter.
l L
2. The test is switched on or off alternately each time the
[ AMS ]
dial is pressed.
l L
3. To return to the previous step, rotate the
to select the desired item, and press the
to enter.
Remarks
Not used for the servicing
Not used for the servicing
Electrical measurement,
CD CLV jitter measurement
Remarks
On or off are switched alternately
On or off are switched alternately
On or off are switched alternately
On or off are switched alternately
On or off are switched alternately
On or off are switched alternately
Stop command in the test mode
SCD-C222ES
[ AMS ]
l L dial to select 59
]
once. When initialization of the
[ OPEN/
A
t Table rotates
[POWER]
switch off.
]
dial to select the menu, and press
[ AMS ]
l L
[ AMS ]
l L
dial
dial
15