Haier AS12NB1HRA-White Service Manual page 40

Wall mounted type dc inverter super match
Table of Contents

Advertisement

Connecting the indoor/outdoor Electric Cable
Removing the wiring cover
Remove terminal cover at right bottom corner of indoor unit, then take off
wiring cover by removing its screws.
When connecting the cable after installing the indoor unit
1. Insert the cable from the outside into the unit through the same
hole that has the interconnecting tubing.
2. Pull out the cable on the front side, and connect the cable
making a loop.
When connecting the cable before installing the indoor unit
Insert the cord from the back side of the unit, then pull it out on the front side.
Fasten the unit wire harness to the conduit holder using the lock nut.
Position the conduit holder to its original state using screw.
Note
When connecting the cable, confirm the terminal number of indoor and
outdoor units carefully. If wiring is not correct, the unit will not operate
properly and could cause a defect.
Indoor unit
4wire 14AWG
(4G0.75mm )
Control Wiring
HSU12VHGL-W
Power cable:
3wire with ground 14AWG
1. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similar qualified person. The type of connecting wire is
H05RN-F or H07RN-F.
2. If the fuse on PC board is broken please change it with the type of
T.3.15A/250VAC (Indoor), T.25A/250VAC (Outdoor).
3. The wiring method should be in line with the local wiring standard.
4. Use an HVACR circuit breaker or time delay fuse.
Outdoor unit
Ensure that no dirt or debris enters the tubing. The standard tubing length is 25 ft/7.5M.
If a different length is required, adjust the refrigerant amount by 1/2 oz/ft, 50 g/M for the
9k, 12k and 18k models. For the 24k model, adjust by 1/2 oz/ft, 50 g/M.Before opening
the service valves, evacuate the interconnecting tubing and indoor unit. Follow the
instruction in section 5 on page 4.
Outdoor unit
38
Installation of Outdoor Unit
Install according to the instructions on the 1st page of this manual
Connection of pipes
When bending the interconnect tubing, ensure the radius is at least 1 1/4" to 1 3/4",
30mm to 40mm to ensure against crushing the tubing.
Connecting the pipe of gas side first makes working easier.
Ensure the interconnecting tubing is approved for R410A.
Forced fastening without careful centering may
Half union
Flare nut
damage the threads and cause a leakage of gas.
Liquid/Gas side9.52mm(3/8") 42 N.m/30.1Ft.lbs
Spanner
Torque wrench
CAUTION
Indoor unit
B
A
Outdoor unit
Outdoor unit
Oil trap
B
Indoor unit
A
Cutting and Flaring Work of Piping
Pipe cutting is carried out with a pipe cutter and burs must be removed.
After inserting the flare nut, flaring work is carried out.
Flare tool for R410A
Clutch-type
clutch-type(Rigid-type) Wing-nut type (Imperial-type)
1.0~1.5mm
0~0.5mm
A
0~1/51 inch
3/76 ~1/17 inch
1.Cut pipe
Flare tooling die
3.Insert the flare nut
Correct
Damage of flare
Lean
System configuration
Pipe Diameter(ǿ)
Fastening torque
Liquid side6.35mm(1/4")
18N.m/13.3Ft.lbs
Gas side 12.7mm(1/2")
55N.m/40.6Ft.lbs
Gas side 15.88mm(5/8")
60 N.m/44.3Ft.lbs
Outdoor unit
B
Indoor unit
A
Max.Elevation: Amax
= 32.8ft / 10m (09k / 12k)
= 50ft / 15m (18k / 24k)
In case the elevation A is more
than 16.4ft / 5m, oil trap shoud be
installed every 5~7m(16.4ft-23ft)
Max. Length: Bmax
= 50ft / 15m (09k / 12k)
= 83.3ft / 25m (18k / 24k)
Conventional flare tool
1.5~2.0mm
1/17 ~1/8 inch
2.Remove burs
4.Flare pipe
Incorrect
Partial
Too outside
Crack
Domestic air conditioner

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Hsu12vhgl-gAs07bs4hraAs09bs4hra

Table of Contents