Whirlpool cabrio WTW8000DW Use & Care Gude page 6

OPTIONS
5
You may add or remove options for each cycle. Not all
options can be used with all cycles, and some are preset
to work with certain cycles.
DELAY START
Touch Delay Start to delay the start of the wash cycle up
to 12 hours "12H". Touch Delay Start until a "0H" appears
in the status display to turn off, or touch POWER.
END BEEP
Use this to turn the signal indicating the end of a wash
cycle to low, medium, high, or off.
NOTE: You may also adjust the tones that sound when a
feature, setting, or option is touched. Touch and hold End
Beep for about 3 seconds to turn key activation sounds to
low, medium, high or off.
STEAM CLEAN (depending on model)
The Steam Clean option adds additional soak and wash
time to many cycles to help remove tough stains, as well
as a steam boost for added cleaning power. Steam Clean
uses a heater within the washer to maintain the selected
temperature setting throughout the wash period. Steam
Clean may be selected as an option with other cycles.
DEEP CLEAN (depending on model)
This option provides enhanced cleaning action for tough
stains. It will add additional agitation and soak time to
the cycle.
CLEAN BOOST (depending on model)
This option provides enhanced cleaning action for tough
stains. It will add additional agitation and soak time to
the cycle.
UTILITY TOOLS
Clean Washer
Use this every 30 washes to keep the inside of your
washer fresh and clean. This cycle uses a higher water
level. Use with affresh
chlorine bleach to thoroughly clean the inside of your
washer. This cycle should not be interrupted. See
"Washer Care."
IMPORTANT: Do not place garments or other items
in the washer during the Clean Washer cycle. Use this
cycle with an empty wash tub.
Rinse & Spin
Combines a rinse and high speed spin for loads
requiring an additional rinse cycle or to complete
a load after power interruption. Also use for loads
that require rinsing only.
EXTRA RINSE
This option can be used to automatically add a second
rinse to most cycles.
PRESOAK
Use this option to add an extra soak period to any cycle
to help loosen tough stains. The washer will fill and then
pause to soak, and then begin the selected cycle.
6
Washer Cleaner tablet or liquid
®
CYCLE MODIFIERS
6
When you select a cycle, its default settings or the previous
cycle selection used will light up.
TEMPERATURE
Temperature Control senses and maintains uniform
water temperatures by regulating incoming hot and
cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results and following
the garment label instructions, use the warmest wash
water safe for your fabric.
• On some models and cycles, warm and hot water will
be cooler than what your previous washer provided.
• Even for cold wash settings, some warm water
may be added to the washer to maintain a minimum
temperature.
SOIL LEVEL
Soil Level (wash time) is preset for each wash cycle.
As you touch the Soil Level pad, the cycle time (minutes)
will increase or decrease in the Estimated Time Remaining
display and a different wash time will appear.
Select the most suitable setting for your load. For heavily
soiled items, select Heavy Soil Level for more wash
time. For lightly soiled items, select Light Soil Level for
less wash time. Lighter soil level setting will help reduce
tangling and wrinkling.
SPIN SPEED
This washer automatically selects the spin speed
based on the cycle selected. The preset speeds can be
changed. Not all spin speeds are available with all cycles.
• Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
• Slower spin speeds mean less wrinkling, but will leave
your load more damp.
7
LID
The Lid Lock ( ) indicator lights up
when the lid is locked and cannot be
opened. If you need to open the lid,
touch and hold START/PAUSE. The lid
will unlock once the washer movement
has stopped. This may take several
minutes if the load was spinning at
high speed. Touch and hold START/PAUSE
button again to restart the cycle.