Precautions On Adjusting - Sony DCR-VX2100 Adjustment Manual

DCR-VX2100/VX2100E
3-1-2.

Precautions on Adjusting

1) The adjustments of this unit are performed in the VTR mode
or camera mode.
To set to the VTR mode, set the power switch to "VCR" (or
"PLAYER") or set the "Forced VTR Power ON mode" using
the adjustment remote commander (Note 1).
To set to the Camera mode, set the power switch to "CAMERA"
or set the "Forced Camera Power ON mode" using the
adjustment remote commander (Note 2).
After completing adjustments, be sure to exit the "Forced VTR
Power ON Mode" or "Forced Camera Power ON Mode".
(Note 3)
2) The handle block (Microphone unit, Microphone amplifier,
remote commander receiver, VTR function key) need not be
connected except during "Battery End Adjustment" and "Audio
adjustments". But removing the handle block (removing the
FK-088 board CN501) means removing the lithium 3V power
supply (ZM-030 board, BT801, 802) , data such as date, time,
user-set menus will be lost. After completing adjustments, reset
these data. If the cabinet (R) has been removed, the self-
diagnosis data, data on history of use (total drum rotation time
etc.) will be lost. Before removing, note down the self-diagnosis
data and the data on the history use (data of page: 2, address:
A2 to AA). (Refer to "SELF-DIAGNOSIS FUNCTION" for
the self-diagnosis data, and to "6-4.Service Mode" for the data
on the history use.) To remove, disconnect the following
connector.
FK-088 board CN501 (40P, 0.8mm)
3) By setting the "Forced VTR Power ON mode" or "Forced
Camera Power ON mode", the video section can be operate
even if the cabinet (L) (Control switch block (CF-4980)) has
been removed. When removing the cabinet (L) disconnect the
following connector.
VC-358 board CN009 (14P, 0.5mm)
4) Cabinet (R) (CK-140 board, LCD block) need not be connected.
To remove the cabinet (R), disconnect the following connector.
VC-358 board CN008 (50P, 0.5mm)
5) The viewfinder (LB-100 board) is need not be connected. To
remove it, disconnect the following connector.
VC-358 board CN002 (27P, 0.3mm)
6) The FP-895 (flexible) is need not be connected. To remove it,
disconnect the following connectors.
VC-358 board CN004 (13P, 0.5mm)
LA-028 board CN053 (27P, 0.5mm)
7) The LA-028 board is need not be connected. To remove it,
disconnect the following connectors.
VC-358 board CN023 (80P, 0.5mm)
8) The CD-512 board of the lens block is need not be connected.
To remove it, disconnect the following connectors.
VC-358 board CN025 (50P, 0.5mm)
Note 1: Setting the "Forced VTR Power ON" mode (VTR mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 02, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the VTR power to be turned on
with the control switch block (CF-4980) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note 2: Setting the "Forced Camera Power ON" mode (Camera mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 01, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the camera power to be turned
on with the control switch block (CF-4980) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note 3: Setting the "Forced Memory Power ON" mode (Memory mode)
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 05, and press the PAUSE
button of the adjustment remote commander.
The above procedure will enable the memory power to be turned
on with the control switch block (CF-4980) removed.
After completing adjustments, be sure to exit the "Forced Power
ON mode".
Note 4: Exiting the "Forced Power ON" mode
1) Select page: 0, address: 01, and set data: 01.
2) Select page: D, address: 10, set data: 00, and press the PAUSE
button of the adjustment remote commander.
3) Select page: 0, address: 01, and set data: 00.
6-38