Subscribe to Our Youtube Channel
Related Manuals for Avigilon 1.0W-H3PTZ-DC20
Summary of Contents for Avigilon 1.0W-H3PTZ-DC20
-
Page 1: Installation Guide
Installation Guide Avigilon High Definition H.264 PTZ IP Dome Camera Models: 1.0W-H3PTZ-DC20 and 2.0W-H3PTZ-DC20 920-0074A-Rev1... -
Page 3: Important Safety Information
Plus IEEE802.3at Type 2 compliant Power Sourcing Equipment (PSE) rated 42.5-57 VDC, 25.5W min. • Any external power supply connected to this product may only be connected to another Avigilon product of the same model series. External power connections must be properly insulated. •... - Page 4 (such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not operate normally, or has been dropped. • Do not use strong or abrasive detergents when cleaning the device body. • Use only accessories recommended by Avigilon.
-
Page 5: Regulatory Notices
Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties authorized by Avigilon Corporation could void the user’s authority to operate this equipment. Disposal and Recycling Information... -
Page 6: Other Notices
The contents of this manual and the specifications of this product are subject to change without notice. Avigilon reserves the right to make changes without notice in the specifications and materials contained herein and shall not be... -
Page 7: Table Of Contents
Table of Contents Overview ......1 Front View ....... . 1 Side View . -
Page 9: Overview
Overview Front View Link LED Connection Status Serial Number Label Feature Description Serial Number Label Product serial number and part number label. Link LED Indicates if there is an active connection in the Ethernet port. Connection Status LED Provides information about device operation. -
Page 10: Side View
Side View Ethernet Port Lanyard Anchor Power Connector Block Clamps Audio/Video Connector I/O Terminals Cover Release Tab Feature Description Power Connector Accepts a terminal block with either AC or DC power Block connection. DC input can be either polarity. Only required when Power over Ethernet is not available. -
Page 11: Installation
Installation Camera Package Contents Ensure the package contains the following: • Avigilon High Definition PTZ Dome Camera • Back panel • Phillips screw driver • Mounting template sticker • Terminal block • I/O connector block Installation Steps Complete the following procedures to install the dome camera. -
Page 12: Preparing The Camera For Installation
Preparing the Camera for Installation NOTE: Be careful not to scratch the dome bubble. Place the camera on a flat surface with the dome facing Press the cover release tab and twist the dome cover until it is released from the base. The dome cover can only move in one direction. -
Page 13: Cutting The Mounting Hole
Cutting the Mounting Hole Use the mounting template to cut a hole in the mounting surface. Remove the mounting template and pull the required cables through the mounting hole. (Optional) Attaching the Back Panel for Plenum Installation If you are installing the dome camera into a plenum space, install the back panel to meet plenum compliance. -
Page 14: Connecting Cables
Connecting Cables Refer to the diagrams in the Overview section for the location of the different connectors. If there are external input or output devices that need to be connected to the camera (for example: door contacts, relays, etc), connect the devices to the camera I/O terminal. -
Page 15: Assigning An Ip Address
Zeroconf, the IP address is in the 169.254.0.0/16 subnet. The IP address settings can be changed using one of the following methods: • (Recommended) Avigilon Camera Installation Tool software application. • Camera's web browser interface: http://<camera IP address>/ •... -
Page 16: Mounting The Ptz Dome Camera
Mounting the PTZ Dome Camera After the cable connections have been made, mount the PTZ dome camera. (Recommended) Attach a safety lanyard from the mounting surface to each of the lanyard anchors to help prevent the camera from falling. Push the PTZ dome camera into the mounting hole. Use the provided screw driver and release the clamps to secure the camera into place. -
Page 17: For More Information
Additional information about setting up and using the device is available in the following guides: • Avigilon Camera Installation Tool User Guide • Avigilon Control Center Client User Guide • Avigilon High Definition H.264 Web Interface User Guide The manuals are available on the Avigilon website: http://avigilon.com/ #/support-and-downloads. -
Page 18: Cable Connections
Cable Connections Connecting External Power NOTE: Do not perform this procedure if Power over Ethernet (POE) is used. If PoE is not available, the dome camera needs to be powered through the removable power connector block. Refer to the diagrams in this guide for the location of the power connector block. -
Page 19: Connecting To External Devices
Connecting to External Devices External devices are connected to the camera through the I/O terminal. The pinout for the I/O terminal is shown in the following table and diagram. Table: External I/O Connector Description +12 VDC, 50 mA max. output for relay drive Relay ground return Relay input 1 Relay input 2... -
Page 20: Connecting To Microphones, Speakers And Video Monitors
When the camera flicker control is set to 60 Hz, the video output signal is NTSC. When the flicker control is set to 50 Hz, the video output signal is PAL. Use the Avigilon Camera Installation Tool to configure the camera’s flicker control in the Image and Display setup. -
Page 21: Led Indicators
LED Indicators Once the camera is connected to the network, the Connection Status LED will display the camera’s progress in connecting to the Network Video Management software. The following table describes what the LEDs indicate: Table: LED Indicators Connection Connection Description State Status LED... -
Page 22: Reset To Factory Default Settings
Reset to Factory Default Settings If the camera no longer functions as expected, you can choose to restore the camera to its factory default settings. Use the firmware revert button to reset the camera. NOTE: Be careful not to scratch the dome bubble. Firmware Revert Button Figure: The firmware revert button between the status LEDs. -
Page 23: Setting The Ip Address Through The Arp/Ping
Setting the IP Address Through the ARP/Ping Method Complete the following steps to configure the camera to use a specific IP address: Locate and copy down the MAC Address (MAC) listed on the Serial Number Tag for reference. Open a Command Prompt window and enter the following commands: arp -s <New Camera IP Address>... -
Page 24: Specifications
Specifications Camera Lens 4.7-94mm, 20x zoom, F1.6 and automatic focus Network Network 100Base-TX Cabling Type CAT5 Connector RJ-45 ONVIF compliant (www.onvif.org) Security Password protection, HTTPS encryption, digest authentication, WS authentication, user access log Protocols IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP, UDP, IGMP, ICMP, DHCP, Zeroconf, ARP, LLDP Streaming Protocols RTP/UDP, RTP/UDP multicast, RTP/RTSP/TCP, RTP/RTSP/HTTP/TCP, RTP/... -
Page 25: Limited Warranty & Technical Support
Limited Warranty & Technical Support Avigilon warrants to the original consumer purchaser, that this product will be free of defects in material and workmanship for a period of 3 years from date of purchase. The warranty period shall be limited to a period of 1 year from date of purchase for all moving parts (including but not limited to fans, pan/tilt motors, lens motors, irises and lens assemblies).
Need help?
Do you have a question about the 1.0W-H3PTZ-DC20 and is the answer not in the manual?
Questions and answers