Download Print this page

Water Temperature Sensor Inspection; Speed Sensor Removal; Speed Sensor Installation - Kawasaki ER-6n Service Manual

Also See for ER-6n

Service manual - 537 pages
Owner's manual - 165 pages
Brochure - 9 pages

629

Advertisement

16-76 ELECTRICAL SYSTEM

Switches and Sensors

Water Temperature Sensor Inspection

•

Remove the water temperature sensor (see Water Tem-

perature Sensor Removal/Installation in the Fuel System

(DFI) chapter).

•

Suspend the sensor [A] in a container of coolant so that

the temperature-sensing projection [C] is submerged.

•

Suspend an accurate thermometer [B] with temperature

-sensing projection [C] located in almost the same depth

with the sensor.

○

The sensor and thermometer must not touch the con-

tainer side or bottom.

•

Place the container over a source of heat and gradu-

ally raise the temperature of the coolant while stirring the

coolant gently.

•

Using the hand tester, measure the internal resistance of

the sensor.

Special Tool - Hand Tester: 57001-1394

If the hand tester does not show the specified values, re-

place the sensor.

Water Temperature Sensor Resistance

Temperature

–20°C (–4°F)

0°C (32°F)

40°C (104°F)

100°C (212°F)

*: Reference Information

Speed Sensor Removal

Never drop the sensor especially on a hard surface.

Such a shock to the sensor can damage it.

•

Remove the engine sprocket cover (see Engine Sprocket

Removal in the Final Drive chapter).

•

Disconnect the speed sensor lead connector [A].

•

Open the clamp [B].

•

Remove:

Bolt [A]

Speed Sensor [B]

Speed Sensor Installation

•

Installation is the reverse of removal.

○

Apply a non-permanent locking agent to the sensor bolt,

and tighten it.

Torque - Speed Sensor Bolt: 6.0 N·m (0.61 kgf·m, 53 in·lb)

NOTE

Resistance (kΩ)

*18.80 ±2.37

*(about 6.544)

1.136 ±0.095

0.1553 ±0.0070

NOTICE

Table of Contents

Show quick links

Advertisement

Chapters

Table of Contents

Troubleshooting

Also See for Kawasaki ER-6n

Kawasaki ER-6n Service Manual

Kawasaki ER-6n Service Manual 537 pages

Kawasaki ER-6n Owner's Manual

Kawasaki ER-6n Owner's Manual 165 pages

KAWASAKI ER-6N Brochure

KAWASAKI ER-6N Brochure 9 pages

Related Manuals for Kawasaki ER-6n

Motorcycle KAWASAKI ER-6N - BROCHURE 2010 Brochure
(2 pages)
Motorcycle KAWASAKI ER-6N ABS - DATASHEET 2011 Datasheet
(3 pages)
Motorcycle Kawasaki ER-6f ABS Service Manual
(625 pages)
Motorcycle Kawasaki ER650A6F Quick Reference Manual
Kawasaki er-6n series motorcycle (14 pages)
Motorcycle Kawasaki ER-6f ABS 2013 Owner's Manual
(134 pages)
Motorcycle Kawasaki EN500 Vulcan 500 LTD Service Manual
Motorcycle (351 pages)

Motorcycle Kawasaki EN500 Service Manual
(338 pages)
Motorcycle Kawasaki EN450 Twins Workshop Manual
(211 pages)
Motorcycle Kawasaki KLX250S Service Manual
(452 pages)
Motorcycle Kawasaki KLX450R Service Manual
(441 pages)
Motorcycle Kawasaki KX450F Service Manual
Kx450f (400 pages)
Motorcycle Kawasaki Z750 Service Manual
Motorcycle (491 pages)

Related Content for Kawasaki ER-6n

This manual is also suitable for:

Er-6n abs

Comments to this Manuals

Latest comments:

Hanne Obel May 07, 2018 04:22:

Hi

I’ve a ER6N 2006, which has run 30.000 km.
Any one who can tell me interval to exchange the oil, check/adjust ventils - and/or if regular service is required?

Thanks a lot for your help/information/advise.

Best regards
Hanne
Zahra Waqar Nov 16, 2017 07:35:

please quote for the following items:
line 30 qty 7
SEAL,BULK NOUN:
PARENT EQUIPMENT/FUNCTION:
MECHANICAL,COMPONENT,BALANCED,O-RING SEC SEAL;
SIZE:35.5 MM HSNG BORE,37 MM SHFT/SLV DIA;
MATERIAL:CARBON ROT FACE,STL STA FACE,
RUBBER GAS KET,STL HARDWARE,STL SPRING;
ADDITIONAL DATA:
FOR KAWASAKI ELECTRO HYDRAULIC POLISHING PUMP
DWG NO: Y307179-1
TYPE 45-4LXA05993,.

KAWASAKI HEAVY INDUSTRIES LTD.:
DWG#510/SEAL