Table of Contents
Advertisement
B-2
Setting the DIP Switches
The DIP switches are each labeled with an "ON"
arrow showing the on direction for each of the 8 indi-
vidual switches in each DIP switch (S1 and S2). The
functions of these switches are also labeled and set
as described below:
Pwr Sources
Head
S1
ON
1
2
3
4
5
6
7
8
S1
Wire Drive Head Selection
The LN-10 control is set up for proper presettable wire
feed speed by setting S1 DIP switches (5 to 8) as
appropriate per the following examples for the head
specification and 10 Series wire drive external gear
selection being used:
For K1563-1,-3 or K1564-Series (LN-10 Boom) or
K1559-1 (LN-10 Bench) with 35-500 IPM (0.89-12.7
m/m) Low Speed Ratio set S1 DIP Switch as follows:
Pwr Sources
ON
1
2
3
S1
For K1563-1,-3 or K1564-Series (LN-10 Boom) or
K1559-1 (LN-10 Bench) with 50-750 IPM (1.25-19.0
m/m) High Speed Ratio set S1 DIP Switch as fol-
lows: (initial factory setting)
Pwr Sources
ON
1
2
S1
For K1563-2,-4 (LN-10 Boom) or K1559-2 (LN-10
Bench) with 55-825 IPM (1.40-21.0 m/m) Low
Speed Ratio set S1 DIP Switch as follows:
Pwr Sources
ON
1
2
S1
For K1563-2,-4 (LN-10 Boom) or K1559-2 (LN-10
Bench) with 80-1250 IPM (2.00-31.8 m/m) High
Speed Ratio set S1 DIP Switch as follows:
Pwr Sources
ON
1
2
S1
OPERATION
M 4 S R + -
ON
1
2
3
4
5
6
7
8
S2
Head
S1
4
5
6
7
8
Head
S1
3
4
5
6
7
8
Head
S1
3
4
5
6
7
8
Head
S1
3
4
5
6
7
8
For K679-1 (Single Head Boom) with 50-770 IPM
(1.27-19.5 m/m) Low Speed Ratio set S1 DIP Switch
as follows:
ON
S1
For K679-2 (Single Head Boom) with 80-1200 IPM
(2.00-30.5 m/m) High Speed Ratio set S1 DIP Switch
S2
as follows:
Pwr Sources
ON
S1
Note: The K679-1 and -2 require the K1562-1 control box.
Welding Power Source Selection
The LN-10 Control is set up for proper presettable
weld voltage control by setting S1 DIP switches (1 to
4) as appropriate per the following information for the
welding power source being used:
CV-250/CV 300-I:
Pwr Sources
ON
1
S1
CV-300/CV 400-I:
Pwr Sources
ON
1
S1
CV-400/CV 500-I:
Pwr Sources
ON
1
S1
CV-655: (initial factory setting)
Pwr Sources
ON
1
S1
V350-PRO And V450-PRO:
Pwr Sources
ON
1
S1
LN-10
Pwr Sources
Head
S1
1
2
3
4
5
6
7
8
Head
S1
1
2
3
4
5
6
7
8
S1
2
3
4
5
6
7
8
S1
2
3
4
5
6
7
8
S1
2
3
4
5
6
7
8
S1
2
3
4
5
6
7
8
S1
2
3
4
5
6
7
8
B-2
Advertisement
Table of Contents
Troubleshooting
