Page 2
RENAULT vehicles. ► ELF lubricants are a major factor in your vehicle’s performance. RENAULT recommends the approved ELF lubricants for your oil changes and top-ups. Contact your RENAULT representative or visit the site: www.lubricants.elf.com The oil born in Formula One...
Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle. Translated from French. Copying or translation, in part or in full, is forbidden unless prior written permission has been obtained from RENAULT, 92 100 Billancourt 2010.
(refer to the informa- for a short while. the word “SERVICE” engraved on the tion on the “RENAULT card: battery" in They may pose a risk to themselves card. Refer to the information on the section 5).
Page 9
Replacement: need for an Using the key additional RENAULT card Refer to the information on “Locking/ If you lose your RENAULT card or unlocking the doors”. require another, you can obtain one Once you have accessed the vehicle from an approved dealer.
With the RENAULT card in zone 1, the functions of the remote control place your hand on a door handle 2: the RENAULT card, it can be used to lock/ vehicle will unlock (in some cases, you unlock without using the RENAULT may need to pull door handle 2 twice to card, when it is in access zone 1.
If a door or the tailgate is open or not closed properly, the vehicle will quickly lock/unlock. Note: a RENAULT card must be within the vehicle's access zone (zone 1) to be able to lock the vehicle using the button.
Page 13
After locking/unlocking the vehicle Note: the maximum distance at which or the luggage compartment only the vehicle locks depends on the sur- using the buttons on the RENAULT roundings. card, remote locking and unlocking in hands-free mode are deactivated. To reactivate the “hands-free” mode:...
Page 14
RENAULT cARd: deadlocking To deactivate deadlocking Unlock the vehicle using button 1 on the RENAULT card. The hazard warning lights flash once to indicate that the doors have been un- locked. To activate deadlocking If the vehicle is equipped with a dead-...
Page 15
RENAULT cARd “sERvIcE” deactivation of the “sERvIcE” mode There are two possibilities: – Press a button on the RENAULT card (not the RENAULT “SERVICE” card); – start the engine with a RENAULT card (not the RENAULT “SERVICE” card). With the card in reader 4, press button 5.
Page 16
Pull on the handle 2. With the doors unlocked or the “hands- After switching off the engine, the lights free” RENAULT card in your posses- and any accessories that are in opera- Lights-on reminder buzzer sion, hold handle 1 and pull it towards tion (radio, etc.) will continue to oper-...
OpENINg ANd cLOsINg THE dOORs (2/2) safety of rear occupants The driver can authorise operation of the rear doors and, depending on the ve- hicle, the electric windows by press- ing switch 1 on the side with the il- lustration. Depending on the vehicle, in the event of a fault: –...
“RENAULT Card” information in Section 1. In certain cases, the RENAULT card may not work: – if the RENAULT card battery is weak, flat, etc. – if equipment operating on the same frequency as the card (mobile phones, etc.) is used;...
Page 19
When you lock the doors, the indicator Unlocking the vehicle from the outside light remains lit and then goes out. is only possible with the RENAULT card in the vehicle's access zone or using the key integrated in the RENAULT Interior locking/unlocking card.
AUTOmATIc LOcKINg WHEN dRIvINg You can decide whether you want to Operating faults activate this function. If you experience an operating fault (no automatic locking, the indicator light in- Operating principle corporated in button 1 does not light up when trying to lock the doors and tail- After the vehicle is started, the system gate, etc.), firstly check that the doors automatically locks the doors when you...
fRONT HEAdREsTs To adjust the angle of the headrest Depending on the vehicle, tilt section A towards or away from you to the re- quired position. To remove the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary).
REAR HEAdREsTs position for use To refit the headrest Raise or lower the headrest while pull- Insert the headrest rods into the ing it towards the front of the vehicle. sleeves, and lower the headrest to the first notch. To remove the headrest storage position Press tabs A of rods 1 and 2 simultane- ously and remove the headrest.
fRONT sEATs WITH mANUAL cONTROL (1/2) To tilt the seatback Turn control knob 3 to the required po- sition. Heated seats (depending on vehicle) With the engine running, turn control 4 to either position 1, 2 or 3 (depending on the temperature required). An in- dicator light on the instrument panel lights up once the front seat heating system is operating.
Page 24
fRONT sEATs WITH mANUAL cONTROL (2/2) To adjust the lumbar support Table function When the front seat is in on the driver’s seat: table position, the front pas- Depending on the vehicle, the passen- Lower handle 5 to increase the support senger air bag must be dis- ger seatback may be folded down onto and lift to decrease it.
fRONT sEATs WITH ELEcTRIc cONTROL Switch 3 is used for adjusting the seat- back and switch 4 is used for adjusting the seat squab. On equipped vehicles, buttons 1 are used to store the chosen driving posi- tion (refer to the following page). Adjusting the seat squab: –...
Page 26
– with the “hands-free” card de- adjustment buttons is pressed during tected or, depending on the vehicle, recall. RENAULT card in the card reader; When driving, it is not possible to – when the driver’s door is opened. recall a driving position.
Page 27
fRONT sEATs: AccEss TO REAR sEATs When a person, an object or a child seat prevents the front seats from lock- ing, perform the following operations: – ask all of the passengers to leave the vehicle and remove any bulky objects from the rear seats;...
sEAT BELTs (1/3) Before starting, first adjust your driv- Always wear your seat belt when trav- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 29
sEAT BELTs (2/3) ß front seat belt reminder warning light This lights up on the central display when the engine is started then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and a bleep sounds for around 2 minutes.
Page 30
sEAT BELTs (3/3) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the restraint system (belts and seats and their mountings) fitted originally. For spe- cial operations (e.g. fitting child seats) contact an approved Dealer. –...
Page 31
mETHOds Of REsTRAINT IN AddITION TO THE fRONT sEAT BELTs (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...
mETHOds Of REsTRAINT IN AddITION TO THE fRONT sEAT BELTs (2/4) Load limiter Air bags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at Depending on the vehicle, the pres- an acceptable level.
Page 33
mETHOds Of REsTRAINT IN AddITION TO THE fRONT sEAT BELTs (3/4) Operation special feature of the front air This system is only operational when the ignition is switched on. After a violent impact, it has two deploy- ment volumes and integrates a ventila- In a severe frontal impact, the air bags tion system: inflate rapidly, cushioning the impact...
Page 34
mETHOds Of REsTRAINT IN AddITION TO THE fRONT sEAT BELTs (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 35
mETHOds Of REsTRAINT IN AddITION TO THE REAR sEAT BELTs force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 36
sIdE pROTEcTION dEvIcEs side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. curtain air bags These are air bags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear side windows...
AddITIONAL mETHOds Of REsTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
cHILd sAfETY: general information (1/2) carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- driver’s responsibility ished growing.
Page 39
cHILd sAfETY: general information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 40
cHILd sAfETY: choosing a child seat Rear-facing child seats forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 41
cHILd sAfETY: choosing a child/baby seat mounting (1/2) There are two ways of attaching child Attachment using the IsOfIX Do not use the child seat seats: via the seat belt or using the system if it may unfasten the seat ISOFIX system.
Page 42
cHILd sAfETY: choosing a child/baby seat mounting (2/2) The ISOFIX anchorage points have been exclu- sively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other objects to these anchorage points. Check that nothing is obstructing the anchorage points.
Page 43
cHILd sAfETY: fitting a child seat (1/6) In the front seat In the rear side seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- A carrycot can be installed across the ing page shows you how to attach a ling in the front passenger seat differ in vehicle and will take up at least two...
Page 44
cHILd sAfETY: fitting a child seat (2/6) Three- and five-seater versions child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 45
cHILd sAfETY: fitting a child seat (3/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Type of child seat seat size Weight of passenger front Rear centre Rear side seats (three and five...
Page 46
cHILd sAfETY: fitting a child seat (4/6) X = Seat not suitable for fitting child seats. U = Seat allowing a child seat with “Universal” approval to be attached by seat belt; check that it can be fitted correctly. IUf/IL = On equipped vehicles, seat which allows a child seat with “Universal, semi-universal or vehicle specific” approval to be fitted using the ISOFIX system.
Page 47
cHILd sAfETY: fitting a child seat (5/6) sport tourer versions child seat attached using the IsOfIX mounting ü Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be fitted.
Page 48
cHILd sAfETY: fitting a child seat (6/6) The table below summarises the information already shown on the diagram on the previous page, to ensure the regula- tions in force are respected. Type of child seat seat size Weight of front passenger Rear centre Rear side seats the child...
cHILd sAfETY: deactivating/activating the front passenger air bag (1/3) dANgER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEvER fit a rear-facing child seat on a front passenger seat with an active front air bag.
Page 50
cHILd sAfETY: deactivating/activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. dANgER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEvER...
Page 51
cHILd sAfETY: deactivating/activating the front passenger air bag (3/3) Activating the front Operating faults passenger air bags It is forbidden to fit a rear-facing child seat to the front passenger seat if the You should reactivate the air bag as air bag activation/deactivation system soon as you remove the child seat from is faulty.
19 Gear lever. ture, radio information, navigation 2 Side window demister outlet. 20 Engine start/stop button and system information, etc. RENAULT card reader. 3 Stalk for: – Driver and front passenger seat 21 Central door locking/unlocking con- – direction indicator lights,...
Page 55
21 Accessories socket. 6 Stalk for: – lighting rheostat for control instru- 22 Engine start/stop control and ments; – direction indicator lights, RENAULT card reader. – activation/deactivation of the trac- – exterior lights, 23 Location for radio, navigation tion control; system, etc.
Page 56
WARNINg LIgHTs (1/4) The presence and operation of the warning lights dEpENd ON THE EQUIpmENT ANd cOUNTRY. side light tell-tale light Left-hand direction indicator tell-tale light á main beam headlight tell-tale Right-hand direction indica- light tor tell-tale light dipped beam headlight tell- Handbrake “on”...
Page 58
WARNINg LIgHTs (3/4) The presence and operation of the warning lights dEpENd ON THE EQUIpmENT ANd cOUNTRY. À Ô Oil pressure warning light Engine coolant temperature warning light If it comes on when you are ® This lights up when the ignition is driving accompanied by the switched on and goes out when the warning light and a beep, it is essential...
Page 59
WARNINg LIgHTs (4/4) The presence and operation of the warning lights dEpENd ON THE EQUIpmENT ANd cOUNTRY. ß ð front seat belt reminder Heated seats operating indi- warning light cator This lights up on the central display This indicates that one of the heated when starting the engine then, if the seats is in operation.
Page 60
dIspLAYs ANd INdIcATORs (1/2) fuel level gauge 5 If the minimum level is reached, in- dicator light 6 comes on and a beep sounds. Fill up as soon as possible. There is only approximately 30 miles (50 km) worth of fuel left after the warn- ing light first comes on.
Page 61
dIspLAYs ANd INdIcATORs (2/2) speedometer 7 (mph or km/h) Instrument panel in miles (option to switch to km/h) Overspeed buzzer – With the ignition off, press one of the Depending on the vehicle and country, buttons 9 or 10 at the end of stalk 2 a buzzer sounds for approximately 10 and start button 8;...
TRIp cOmpUTER ANd WARNINg sYsTEm (1/10) c) mileage before service; d) tyre pressure monitor; e) vehicle settings customisation menu; f) trip log, operating faults and informa- tion message readout. Trip computer and warning display selection keys 2 system 1 and 3 Depending on the vehicle, this includes Scroll through the following information the following functions:...
Page 63
TRIp cOmpUTER ANd WARNINg sYsTEm (2/10) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
Page 64
TRIp cOmpUTER ANd WARNINg sYsTEm (3/10) The display of information shown below dEpENds ON THE vEHIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. b) Journey parameters. fuel used. Fuel consumed since the last reset. Average fuel consumption since the last reset.
Page 65
TRIp cOmpUTER ANd WARNINg sYsTEm (4/10) The display of information shown below dEpENds ON THE vEHIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected current fuel consumption. This value is displayed above a speed of approximately 18 mph (30 km/h).
Page 66
TRIp cOmpUTER ANd WARNINg sYsTEm (5/10) The display of information shown below dEpENds ON THE vEHIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected c) mileage before service. Distance remaining until the next service (displayed in miles (kil- ometres) and months), then when the service nears, several sce- narios are possible: –...
Page 67
TRIp cOmpUTER ANd WARNINg sYsTEm (6/10) Journey parameters (1/2) The display of information shown below dEpENds ON THE vEHIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected d) Tyre pressure monitor Refer to the information on the “Tyre pressure monitor” in Section 2.
Page 68
TRIp cOmpUTER ANd WARNINg sYsTEm (7/10) Journey parameters (2/2) The display of information shown below dEpENds ON THE vEHIcLE EQUIpmENT ANd cOUNTRY. Examples of selections Interpreting the display selected e) vehicle settings customisation menu. Enables certain vehicle functions to be set (instrument panel language, parking distance control, etc.).
“Battery low start engine” switched off for some time whilst listening to the radio). “please remove keycard” Request to remove the RENAULT card from the reader when you leave the vehicle. “checking control Displayed with the ignition on when the vehicle is running self-diagnostics.
TRIp cOmpUTER ANd WARNINg sYsTEm (10/10) Warning messages ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. stop your engine and do not restart it. contact an approved dealer. Examples of warning messages are given in the following pages.
vEHIcLE sETTINgs cUsTOmIsATION mENU Once a line has been selected, keep pressing either button 2 or 3 to change the function: If you select either “Parking sensor volume” or “LANGUAGE”, you will be given a new choice of options (parking distance control volume or in- strument panel language).
sTEERINg WHEEL/pOWER-AssIsTEd sTEERINg power-assisted steering Operating faults The steering may become stiff when variable power-assisted steering driving or when the steering wheel is The variable power-assisted steering turned repeatedly. This is due to the system is equipped with an electronic power assistance overheating.
cLOcK ANd EXTERIOR TEmpERATURE vehicles equipped with a External temperature navigation system, radio, etc. indicator For vehicles which are not fitted with special note: buttons 2 and 3, refer to the specific When the external temperature is be- equipment instructions to discover the tween –3°C and +3°C, the °C charac- special features.
REAR vIEW mIRRORs folding door mirrors The door mirrors automatically fold in when the vehicle is locked (switch 2 in position B). In this case, they will fold out when the ignition is next switched In any case, you can make the door mirrors fold in (switch 2 in position C) or fold out (switch 2 in position A).
AUdIBLE ANd vIsUAL sIgNALs direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0.
EXTERIOR LIgHTINg ANd sIgNALs (1/3) daytime running lights function Depending on the vehicle, the daytime running lights come on automatically when the engine is started. To activate or deactivate this function, refer to the information on the “Vehicle settings customisation menu” in Section 1. main beam headlights á...
EXTERIOR LIgHTINg ANd sIgNALs (2/3) special note: “see-me-home lighting” – If the dipped beam headlights are function manually switched on and if the light This function allows you to briefly switch is sufficient, the directional head- on the dipped beam headlights (to pro- lights will remain fixed;...
EXTERIOR LIgHTINg ANd sIgNALs (3/3) front fog lights switching off the lights Turn centre ring 5 on stalk 1 Turn ring 5 again until mark 6 is oppo- until the symbol faces mark 6, then re- site the symbol for the fog light that you lease it.
Page 80
ELEcTRIcAL AdJUsTmENT Of THE dIppEd BEAm HEAdLIgHTs Examples of positions for adjusting control A according to the load five door Three door driver alone or with front passenger driver with one front passenger and one rear passenger On vehicles fitted with this function, control A allows you to adjust the height of the beams according to the load.
WINdscREEN WAsH/WIpE (1/2) vehicle fitted with front windscreen wiper rain sensor A park B automatic wiper function. When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed. It is possi- ble to change the triggering thresh- old and the time sweeps by turning ring 2:...
WINdscREEN WAsH/WIpE ( Headlight washers Headlights on On equipped vehicles, hold stalk 1 pulled towards you for about 1 second, and the headlight washers and wind- screen washers will be activated at the same time. Note: when the minimum windscreen washer fluid level is reached, the head- light washer system may be deprimed.
REAR scREEN WAsH/WIpE Rear screen washer/ wiper With the ignition on, push the stalk. Check the condition of the wiper blades. You are responsible for their service life: – they must remain clean: clean the blades, windscreen and rear screen regularly with soapy Rear screen wiper water;...
fUEL TANK (1/2) fuel grade vehicles running on ethanol-based fuel Use a high-grade fuel that complies with the legislation in force in each It is essential to use unleaded petrol or country and which must conform to the fuel containing a maximum of 85% eth- specifications given on the label on the anol (E85).
fUEL TANK (2/2) filling with fuel persistent smell of Insert the nozzle to open the valve A fuel and insert fully before turning it on to If you notice a persistent fill the fuel tank (risk of splashing). smell of fuel you should: Keep the nozzle in this position through- –...
RUNNING IN Petrol version Diesel version Up to 600 miles (1,000 km), do not For the first 900 miles (1,500 km), do exceed 78 mph (130 km/h) in top gear not exceed 2,500 rpm. After complet- or 3,000 to 3,500 rpm. ing this mileage you may drive faster, however, it is only after approximately You may only expect top performance...
2 or in detection zone 3. When you get into the vehicle, insert the Starting with the tailgate RENAULT card fully into card reader 2. To start, depress the brake or clutch open (in hands-free mode) pedal and press button 1. If a gear To start, press button 1.
Page 90
(2/2) Operating faults In certain cases, the hands-free RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc. – near to appliances operating on the same frequency as the card (moni- tor, mobile phone, video game, etc.);...
When you leave your vehi- hold” appears on the instrument panel: cle, especially if you have press button 1 for longer than two sec- your RENAULT card with onds. you, check that the engine is completely switched off. Hands-free RENAULT card With the card in the vehicle, press button 1: the engine will stop.
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
GEAR LEVER/HANDbRAkE Handbrake To release: Pull lever 2 up slightly, press button 3 and then lower the lever to the floor. To apply: Pull the lever 2 upwards and make sure the vehicle is immobilised. Make sure that the hand- brake is properly released Selecting reverse gear when driving (red indicator...
ELECTRONIC PARkING bRAkE (1/3) Note: To indicate that the electronic parking brake is applied or released, a beep sounds and the message “Apply park- ing brake” appears on the instrument panel: – with the engine running: when the driver’s door is opened; –...
3 at the same time; You can control the electronic parking To manually activate the electronic – remove the RENAULT card from the brake manually. parking brake, (when stopping at a red card reader. light, or stopping when the engine is Applying the electronic parking running, etc.): pull and release switch 3.
ADVICE: antipollution, fuel economy and driving (1/3) Aiding fuel economy Your vehicle complies with criteria for Have your vehicle adjusted and recycling and recovering vehicles at the checked by an approved Dealer, in ac- Depending on the vehicle, in order to end of their service life which will come cordance with the instructions given in optimise consumption, an indicator light...
Page 99
ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring – Brake as little as possible. If you an- ticipate an obstacle or bend in ad- system vance, you may then simply release The exhaust gas monitoring system will the accelerator pedal. detect any operating faults in the vehi- –...
Page 100
ADVICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
This commitment is illustrated by the less fuel (eg. 140 g/km, equivalent to the vehicle components have been de- Renault eco² group signature. 5.3 l/100 km for a diesel vehicle). signed to enable them to be recycled. Our vehicles are also equipped with a...
TyRE PRESSURE MONITOR (1/3) The tyre pressure can be adjusted If the vehicle is equipped with the func- tion, this system monitors the tyre pres- when cold (refer to the information on sure. “Tyre pressures”). If tyre pressures cannot be checked when the tyres are cold, the recom- Operating principle mended pressures must be increased...
Page 103
TyRE PRESSURE MONITOR (2/3) “Puncture” Wheel F indicates that the wheel con- cerned is punctured or severely un- derinflated. Replace it or contact an approved dealer if it is punctured. Top up the tyre pressure if the wheel is de- flated, This message appears along with the ®...
Page 104
TyRE PRESSURE MONITOR (3/3) Emergency spare wheel Tyre repair product and If the vehicle is equipped with an emer- inflation kit gency spare wheel, it will not have a Because the valves are specially de- sensor. When it is fitted to the vehicle, signed, only use equipment approved the message “Tyre pressure sensors by the approved network.
DRIVER CORRECTION DEVICES/AIDS (3/4) Hazard warning lights switching on Traction control (A.S.R.) offers addi- tional safety; it is recommended that Depending on the vehicle, these may you do not drive with the function disa- light up in the event of sudden decel- bled.
Page 108
DRIVER CORRECTION DEVICES/AIDS (4/4) Hill start assistance This function assists the driver when starting on hills. It prevents the vehicle The hill start assistance from rolling backwards, depending on system cannot completely the slope, by automatically applying the prevent the vehicle from brakes when the driver lifts his/her foot rolling backwards in all sit- off the brake pedal to depress the ac-...
Page 109
CRUISE CONTROL/SPEED LIMITER: speed limiter function (1/3) Controls Switching on The speed limiter function helps you stay within the driving speed limit that Press switch 1 on the side showing 1 Main “On/Off” switch. you choose, known as the limit speed. Indicator light 7 comes on, lit orange, 2 Limit speed activation, storage and and the message “Speed limiter”...
CRUISE CONTROL/SPEED LIMITER: speed limiter function (2/3) Varying the limit speed Exceeding the limit speed The limit speed may be changed by re- It is possible to exceed the limit speed peatedly pressing: at any moment. To do this: press the accelerator pedal firmly and fully –...
Page 111
CRUISE CONTROL/SPEED LIMITER: speed limiter function (3/3) Putting the function on Recalling the limit speed Switching off the function standby If a speed has been stored, it can be re- The speed limiter function is deacti- called by pressing switch 5 (R). vated if you press switch 1: in this case The speed limiter function is sus- a speed is no longer stored.
Page 112
CRUISE CONTROL/SPEED LIMITER: cruise control function (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. Controls The cruise control function helps you to Therefore, it can under no circum- maintain your driving speed at a speed stances replace the driver’s respon- that you choose, called the cruising...
Page 113
CRUISE CONTROL/SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving At a steady speed (above 20 mph Once a cruising speed is stored and Press switch 1 on the side showing (30 km/h) approximately) press the cruise control function is active, Indicator light 7 comes on, lit green, and switch 2 (+): the speed is stored.
Page 114
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed Putting the function on standby The cruising speed may be exceeded at any time by depressing the acceler- The function is suspended when you: ator pedal. The cruising speed flashes –...
Page 115
CRUISE CONTROL/SPEED LIMITER: cruise control function (4/4) Switching off the function Returning to the cruising speed Note: if the speed previously stored is If a speed is stored, it can be recalled, much higher than the current speed, The cruise control function is deacti- once you are sure that the road condi- the vehicle will accelerate more rapidly vated if you press switch 1: in this case...
PARkING DISTANCE CONTROL (1/3) Operating principle Front parking distance control Ultrasonic detectors, installed in the (depending on vehicle) front or rear bumper depending on the vehicle, measure the distance between Operation the vehicle and an obstacle whilst re- The parking distance control system versing.
Page 117
PARkING DISTANCE CONTROL (2/3) Automatic activation/deactivation of the rear parking distance control The system deactivates: – when the electronic parking brake is applied; – when the vehicle speed is above ap- proximately 6 mph (10 km/h); – when the vehicle is stationary for more than approximately five sec- onds and an obstacle is detected (such as when in a traffic jam etc.);...
PARkING DISTANCE CONTROL (3/3) Temporary deactivation of Special features the system Ensure that the ultrasonic sensors are not obscured (by dirt, mud, snow, etc.). (depending on the vehicle) Press switch 1 to deactivate the system. Operating faults The message “Parking sensor off” is When the system detects an operating displayed to remind you that the system fault there will be a 5-second continu-...
AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Select position D. In most traffic con- ditions, you will not have to touch the gear selector lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particu-...
AUTOMATIC TRANSMISSION (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, – If the road contours and bends When the vehicle is stopped, move the move the lever to the left. Shifting the do not allow you to stay in auto- lever to position P while keeping your lever repeatedly allows you to change...
Page 121
AUTOMATIC TRANSMISSION (3/3) Operating faults – When driving, if the message “Check auto gearbox” appears on the instrument panel, this indicates there is a fault. Contact your approved Dealer as soon as possible. – When driving, if the message “Auto gearbox overheating”...
AIR VENTS: air outlets (1/2) Depending on the vehicle: 1 left-hand side air vent 2 left-hand side window demister outlet 7 passenger footwell heater outlets 3 windscreen demister outlets 8 centre console air vents 4 centre air vents 9 air conditioning control panel 5 right-hand side air vent 6 right-hand side window demister outlet...
AIR VENTS: air outlets (2/2) Air flow Direction To remove bad odours from your ve- hicles, only use the systems designed Turn control knob 1 (beyond the point Right/left: move tabs 2 to the right or for this purpose. Consult an approved of resistance).
MANuAl AIR coNDITIoNINg (1/2) Distribution of air in the passenger compartment There are five air distribution options. Turn control 4 to choose the distribution option. The air flow is directed to the windscreen and the front side window demisting vents. The air flow is distributed be- tween all the air vents, the front side window demisting vents, the...
MANuAl AIR coNDITIoNINg (2/2) “oFF" position: the system is deactivated: the ventila- tion speed for the passenger compart- ment air is zero (vehicle stationary), you can however still feel a slight flow of air when the vehicle is moving. Recommended demisting option: Turn controls 1, 2 and 4 to the position.
AuToMATIc clIMATE coNTRol (1/5) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), whilst optimising consumption. The system controls the ventilation speed, air distribution, air recircula- tion, and starting and stopping the air conditioning and air temperature.
Page 129
AuToMATIc clIMATE coNTRol (2/5) clear View function Press button 10: the integrated indica- tor light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
Page 130
AuToMATIc clIMATE coNTRol (3/5) The displayed temperature values show a comfort level. When starting the engine, increas- ing or decreasing the value dis- played will not allow the com- fort level to be reached any more quickly. The system will always op- timise the temperature increase or decrease (the ventilation system does not start instantly at maximum...
Page 131
AuToMATIc clIMATE coNTRol (4/5) The air flow is directed to the windscreen and the front side window demisting vents. × The air flow is distributed be- tween all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells.
Page 132
AuToMATIc clIMATE coNTRol (5/5) Recycling This function is controlled automati- cally, but it can also be activated manu- ally. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; –...
AIR coNDITIoNINg: information and advice on use Advice on use In some situations, (air conditioning operating faults off, air recirculation activated, venti- Fuel consumption lation speed at zero or low, etc.) you As a general rule, contact your ap- You will normally notice an increase may notice that condensation starts proved Dealer in the event of an op- in fuel consumption (especially...
Never leave your vehicle with the Electric windows From the driver’s seat, use switch: RENAULT card inside and never 1 for the driver’s side; Press or pull the switch to raise or lower leave a child (or a pet) unsuper- 2 for the front passenger side;...
(some- body’s fingers, etc.) it stops and then moves back several centimetres. Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a Sun blind Sunroof child (or a pet) unsupervised, even –...
Technical Department; RENAulT card twice in quick suc- (the window will close gradually), hold – do not open the sunroof immedi- cession, or on the driver's door in...
MANuAl wINDow wINDERS/INTERIoR lIghTINg (1/2) Manual window winders courtesy light Front door lights Turn handle 1. Tilt switch 3 to move it to the position Light 5 comes on when the door is for: opened. – permanent lighting; – intermittent lighting, which comes on when a door is opened.
INTERIoR lIghTINg /SuN VISoR (2/2) glove box light 6 Sun visor luggage compartment light 9 Light 6 comes on when the cover is Lower the sun visor 7 over the wind- Depending on the vehicle, light 9, opened. screen or unclip it and turn it over the comes on when the luggage compart- side window.
PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS (1/4) Door pockets 1 Driver and passenger Sun visor storage 3 underfloor storage This can be used for storing motorway compartments 2 tickets, cards, etc. This storage compartment can be used to hold the vehicle documentation, etc. Ensure that no hard, heavy Nothing should be placed or pointed objects are...
PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS (2/4) Front centre armrest storage centre console storage Passenger storage compartment A compartments 6 compartment Press button 4 and lift the cover 5. Pull handle 7 to open it. The glove box can hold A4-size docu- ments, a large bottle of water, etc.
Page 141
PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS (3/4) Door pockets 8 Storage compartment 9 Rear armrest storage Lower armrest 12 and, depending on the vehicle, lift cover 11 using unlock- ing handle 10. 3.19...
Page 142
PASSENgER coMPARTMENT SToRAgE SPAcE AND FITTINgS (4/4) clothes hooks 13 Front seat storage Rear centre console storage compartments 15 compartments 16 grab handle 14 This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.
AShTRAY, cIgAR lIghTER, AccESSoRIES SockET Accessories sockets cigar lighter 1 Ashtray 2 You may use cigar lighter recess 1 or With the ignition on, push in cigar To open, lift the cover. To empty, pull the socket 3 (depending on the vehicle). lighter 1, it will spring back with a click ashtray towards you and it will be re- They are designed for connecting ac-...
REAR BENch SEAT (1/3) Sport tourer versions To fold down the seatback Press button 1 lower seatback(s) A. Ensure that the front seats are far Depending on the vehicle, seatback A enough forward. can be folded down on its own to allow long or bulky objects to be transported.
REAR BENch SEAT (2/3) luggage compartment carpet level adjustment To adjust the level of the luggage com- partment carpet in line with the seat- backs, lift carpet 4 via the rear door; height adjuster 5 is deployed automat- when refitting the seat- ically.
Page 146
REAR BENch SEAT (3/3) When moving the rear bench seat, ensure that nothing obstructs the an- chorage points (part of the The seat and the seatback may be body, a pet, gravel, cloth, toys, etc.). folded away to allow bulky objects to be carried.
TAIlgATE opening manually from To open inside the vehicle Press button 1 and lift the tailgate. Special note: To close If it is impossible to unlock the tailgate, Pull down the tailgate using handle 2 it can be done from inside. inside the tailgate to assist you.
REAR PARcEl ShElF Removal Lift rear parcel shelf 2 slightly and pull it Unclip mountings 3 on either side of towards you. the parcel shelf, then remove the parcel Unhook the two cords 1 (tailgate side). shelf via the luggage compartment. To refit it, proceed in reverse order to removal.
luggAgE coMPARTMENT coVER: sport tourer versions (1/2) To remove the flexible Removing the luggage cover section of the luggage cover Push the luggage compartment cover to the left (movement A) and lift the Pull handle 1 gently to release the pins right-hand side of the inertia reel (move- from their mounting points located on ment B).
Page 150
luggAgE coMPARTMENT coVER: sport tourer versions (2/2) luggage compartment cover Store luggage compartment cover 6 behind the booster seat 5 in the dedi- storage cated storage compartment. From the rear doors, lower the bench seat seatback (refer to information on the “Rear bench seat”...
luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (1/3) Storage under carpet 1 Anchorage points Side straps (depending on vehicle) (Three- and five-seater versions) Side straps 3 are located either side of To open, fold back carpet A. Hooks 2 located on each corner of the the luggage compartment, and can be luggage compartment, allow the load to used to store an oil can.
Page 152
luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (2/3) Anchorage points Storage under carpet (sport tourer version) (sport tourer version) Hooks 5, located on either side of the To access storage compartments 7, luggage compartment, allow the load to fold back section B using handle 4 and, be secured.
Page 153
luggAgE coMPARTMENT SToRAgE SPAcE AND FITTINgS (3/3) Separating the luggage On the back there is an elastic strip 9 to hold small objects vertically in position. compartment (sport tourer version) The loading area can be separated. Turn locks 8 situated on either side of the luggage compartment to the first notch.
TRANSPoRTINg oBjEcTS IN ThE luggAgE coMPARTMENT/TowINg (towing equipment) Always place the objects to be trans- ported so that their largest side rests against the back of the rear bench seat, for normal loads (Example A), or Always position the heavi- against the back of the front seats when est items directly on the the rear bench seatbacks are folded...
TRANSPoRTINg oBjEcTS: luggage net (1/2) Fitting the luggage net behind the front seats Inside the vehicle on each side: – lift cover 1 to access the upper mounting ring of the net; – fix the net belt hook onto the ring; luggage net A –...
Page 156
TRANSPoRTINg oBjEcTS: luggage net (2/2) – in the luggage compartment, fix the lower mounting strap hook on the net to the anchorage point 4 located under the luggage compartment carpet; – adjust the net strap so that it is taut. Fitting the luggage net behind the rear bench seat Inside the vehicle on each side:...
RooF BARS: AccESS To FIxINg PoINTS Three door version The fitting of roof bars is prohibited on Sport tourer versions three door versions. For vehicles fitted with original roof bars, the roof bars are fixed and must not be removed. To change them contact an approved Dealer.
MulTIMEDIA EquIPMENT Navigation system The equipment described below may or may not be fitted to the vehicle, and its location may vary, depending on the vehicle navigation system version. 1 Radio; 2 CD or DVD reader; 3 Central control; 4 Steering column control; 5 Micro.
BOnnet Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.
engine Oil level: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact your approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.
Page 162
engine Oil level: general information (2/2) Consult your approved Dealer at once if you notice an abnormal or repeated drop in any of the fluid Maximum engine oil level levels. exceeded. The oil level should only be read with the dipstick as explained above. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
engine Oil level: topping up/filling (1/2) topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
engine Oil level: topping up/filling engine Oil CHAnge (2/2) engine oil change: if you are changing the oil when the engine is hot, be careful not to scald yourself if the oil overflows. Never run the engine in an enclosed space as exhaust gases are poisonous.
levelS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Service (very severe damage is likely to be Booklet for your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
levelS (2/3) level 1 topping up It is normal for the level to drop as After any operation on the hydraulic cir- the linings become worn, but it should cuit, a specialist must replace the fluid. never drop below the Min line. Only use fluids approved by our If you wish to check the disc and drum Technical Department (and taken from...
levelS FilteRS (3/3) Filters liquid Screen wash product (product with an- The replacement of filter elements (air tifreeze in winter). filter, passenger compartment filter, diesel filter, etc.) is scheduled in the Jets maintenance operations for your vehi- cle. Use a tool such as a needle to adjust the height of the windscreen washer Replacement intervals for filter el- jets.
tyRe pReSSURe tyre safety and use of snow chains Refer to the information on “Tyres” in Section 5 for the servicing con- ditions and, depending on the ver- sion, the use of chains. Special note For vehicles used fully laden (maximum permissible all-up...
BAtteRy Depending on the vehicle, a system continuously checks the battery charge status. If the level drops, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. Then the message “Battery charging” appears on the in- strument panel for the duration of the charging time.
BODyWORk MAintenAnCe (1/2) protection against the effects you should not: – Use solvents not approved by our Technical Department to remove of corrosive agents – Degrease or clean mechanical com- stains as this could damage the ponents (e.g. the engine compart- Although your vehicle has been treated paintwork.
Page 171
BODyWORk MAintenAnCe (2/2) you should – Observe the vehicle stopping dis- – Before going through a roller type car tances when driving on gravelled wash, return the windscreen wiper – Wash your car frequently, with the surfaces to prevent paint damage. stalk to the Off position (refer to engine off, with cleaning products the information on the “Windscreen...
inteRiOR tRiM MAintenAnCe – Seat belts you should not: Whatever type of stain is on the trim, use soapy water (if possible, warm These must be kept clean. You are strongly advised not to po- water) containing: sition objects such as deodorants, Use products selected by our –...
Puncture, emergency sPare wheel In the event of a puncture, special note: depending on the vehicle, The Tyre Pressure Monitor function you will have: does not check the emergency spare wheel (the wheel replaced by the emer- An emergency spare wheel or tyre in- gency spare wheel disappears from the flation kit (refer to the information on the instrument panel display).
Page 175
tyre Pressure KIt (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 176
tyre Pressure KIt (2/3) with the ignition on, Depending on the vehicle, in the event of a puncture, use the kit located under- – connect adapter 8 to the accessories neath the luggage compartment carpet. socket on the dashboard of the vehi- Depending on the vehicle, remove the cle;...
Page 177
tyre Pressure KIt (3/3) Precautions when using the – affix driving recommendation label 9 to the dashboard where it can easily be seen by the driver; The kit should not be operated for more – store the kit; than 15 consecutive minutes. –...
tOOl KIt/wheel trIm – wheel wheelbrace 1 Jack 2 When replacing the jack, fold it cor- rectly and position the wheelbrace cor- rectly before replacing it in its position. hubcap tool 3 This tool is used to remove the wheel trims.
changIng a wheel (1/2) Vehicles equipped with a jack Offer up the jack 4 horizontally; the jack head must be lined up with jacking and wheelbrace point 1 located on the underside of the If necessary, remove the wheel trim. sill, closest to the wheel concerned, as shown by arrow 2.
Page 180
changIng a wheel (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
tyres (1/3) tyre and wheel safety When the tyre tread has been worn to the level of the wear indicators, they The tyres are the only contact between become visible 2: it is then necessary the vehicle and the road, so it is essen- to replace your tyres because the tread tial to keep them in good condition.
tyres (2/3) tyre pressures Fitting new tyres Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including which may be reached in hot weather the emergency spare wheel). The tyre For safety reasons, this op- or following a fast journey.
Page 183
tyres (3/3) use in winter chains In all cases, we would recommend that you contact an approved dealer For safety reasons, fitting snow who will be able to advise you on chains to the rear axle is strictly for- the choice of equipment which is bidden.
heaDlIghts: changing bulbs (1/2) Daytime running light After opening the bonnet, pull tool A Do not touch the bulb glass. hold it upwards. Remove the two screws 1 by its base. Remove the cover C, unlock the bulb from the headlight using the tool. When the bulb has been changed, holder 2 by rotating it.
Page 185
heaDlIghts: changing bulbs (2/2) To comply with current legislation, or as a precaution, you can obtain an emergency kit from an approved dealer containing a set of spare bulbs and fuses. The bulbs are under pres- sure and can break when replaced.
Page 186
heaDlIghts: additional/front fog lights additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved Dealer. Front fog lights 1 However, because the front bumper needs to be removed, you are advised to have your bulbs replaced by an approved dealer.
rear lIghts anD InDIcatOr lIghts: changing bulbs (1/6) Five-door versions – loosen nut 1, press down on it to Direction indicator lights 5 release the front of the light (move- Bulb type: Py21w. Direction indicator lights/brake and ment A) then remove the nut; side light and brake light 6 side lights –...
Page 188
rear lIghts anD InDIcatOr lIghts: changing bulbs (2/6) Five-door versions – Lower the tailgate, then pull light 9 reversing light 10 towards the rear to release it. (continued) Bulb type: w16w. – Unscrew the bulb holder for the bulb Fog light/side light 11 Fog lights/side lights and reversing concerned.
Page 189
rear lIghts anD InDIcatOr lIghts: changing bulbs (3/6) three-door versions 16 side light/stop light Bulb type: P21/5w. – Unclip the access flap; 17 Direction indicator light – unscrew nuts 12 and 13; Bulb type: Py21w. – from the outside, remove bolt 14, then pull on the light;...
Page 190
rear lIghts anD InDIcatOr lIghts: changing bulbs (4/6) sport tourer Versions side light 22 Bulb type: w5w. side lights/reversing lights and fog reversing light 23 lights Bulb type: P21w. – From the luggage compartment, unclip flap 20 (movement C), then Fog light 24 remove the bolts .
InterIOr lIghtIng: changing bulbs (1/2) courtesy light Door lights glove box light – Position the 3 switches in the central Unclip light 2 (using a flat-blade screw- Open the access cover 3, you can then position; driver or similar). unclip the bulb holder more easily 4. –...
InterIOr lIghtIng: changing bulbs (2/2) luggage compartment light Disconnect the light. Press tab 6 to release lens 8 and Unclip the light at 5 using a flat-blade access bulb 7. screwdriver or similar. Bulb type: w5w. The bulbs are under pres- sure and can break when replaced.
Fuses (1/2) CORRECT INCORRECT Fuse box tweezers 1 If any electrical component does not Remove the fuse using tweezers 3, lo- work, check the condition of the fuses. cated at the back of cover A or B. Unclip cover A or B (depending on ve- To remove the fuse from the tweezers, Check the fuse in question hicle).
Fuses (2/2) allocation of fuses 8 Interior rear-view mirror; Some accessories are protected by fuses located in the engine compart- (the presence of certain fuses depends 9 Rear screen wiper; ment in fuse box C. on the vehicle equipment level) 10 and 11 Rear electric windows;...
Battery: troubleshooting (1/2) to avoid all risk of sparks: connecting a battery charger – Ensure that any electrical consumers the battery charger must be com- (courtesy lights, etc.) are switched patible with a battery with nominal off before disconnecting or recon- voltage of 12 volts.
Page 198
Battery: troubleshooting (2/2) starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
(insert the the next time the vehicle is started, the place the RENAULTcard battery, press RENAULT card in the card reader) and message will disappear. button 1, pulling on emergency key 2, lock/unlock the vehicle (refer to the in- then unclip cover 3 using tab 4.
FIttIng a raDIO If your vehicle is not fitted with an audio system, one can be fitted and locations have been provided for: – the radio 1; – tweeter speakers 2; – bass speakers 3. To install any equipment, please con- –...
accessOrIes Before fitting an electrical or If you are using an anti-theft electronic device (particu- device, only attach it to the larly for transmitters/receiv- brake pedal. ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.
wInDscreen wIPer BlaDes Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
If your vehicle is the towing or r for vehicles with automatic trans- vehicle, do not exceed the maximum missions), insert the RENAULT card in towing weight for your vehicle (refer to the card reader then press the engine the information on “Weights”...
– at the rear, towing point 5; Unclip cover 3 or 6 by sliding a flat tool (or the key integrated in the RENAULT – at the front, towing hitch 4 (lo- card) under the cover.
POssIBle causes what tO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the information on “Locking/unlocking the...
Page 206
The engine will not start. Starting conditions are not fulfilled. Refer to the information on “Starting/stop- ping the engine” in Section 2. The hands-free RENAULT card Insert the card in the card reader in order to does not work. start the engine.
Page 207
OPeratIng Faults (3/5) On the road POssIBle causes what tO DO The steering column remains locked. Steering wheel locked. Move the steering wheel while pressing the engine start button (refer to the information on “Starting the engine” in Section 2). Coolant boiling in the coolant reser- Mechanical fault: damaged cylinder Stop the engine.
Page 208
OPeratIng Faults (4/5) On the road POssIBle causes what tO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine overheats. The coolant Engine cooling fan not working. Stop the vehicle, switch off the engine and temperature indicator is in the warn- contact an approved dealer.
Page 209
OPeratIng Faults (5/5) electrical equipment POssIBle causes what tO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. The wiper does not stop. Faulty electrical controls. Consult an approved dealer.
Vehicle identification plates the information shown on the ve- 6 Technical specifications of vehicle. hicle identification plate should be 7 Vehicle paint reference. quoted on all correspondence or 8 Equipment level. orders. 9 Vehicle type. 10 Trim code. Vehicle identification plate A 11 Additional equipment specifica- 1 Vehicle type and chassis number.
engine identification plates (1/2) the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 214
engine identification plates (2/2) the information on the engine plate (or label) C should be quoted on all your correspondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
engine specifications Versions 1.4 tce 1.6 16V 2.0 16V 2.0 t 1.5 dci 1.9 dci 2.0 dci engine type H4J Turbo F4R Turbo (see engine plate) cubic capacity (cc) 1,395 1,598 1,998 1,998 1,461 1,870 1,995 It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel filler flap.
Weights (in kg) the weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. consult your approved dealer. maximum permissible all-up weight (mmac) Weights are indicated on the vehicle identification plate (refer to total train weight (mtR) the information on “Vehicle identification plates”...
Replacement paRts and RepaiRs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
seRVice sheets (1/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
Page 222
seRVice sheets (2/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
Page 223
seRVice sheets (3/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
Page 224
seRVice sheets (4/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
Page 225
seRVice sheets (5/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
Page 226
seRVice sheets (6/6) Vin: .................. Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □ anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........ □...
anticoRRosion check (1/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...
Page 228
anticoRRosion check (2/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...
Page 229
anticoRRosion check (3/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.19...
Page 230
anticoRRosion check (4/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.20...
Page 231
anticoRRosion check (5/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.21...
Page 232
anticoRRosion check (6/6) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.22...
AlphAbeticAl index (1/5) ABS ..............1.51, 2.19 → 2.22 catalytic converter............2.6 – 2.7 accessories................ 5.29 central door locking ........1.8, 1.12 → 1.14 accessories socket ............3.21 changing a bulb .............5.12 → 5.20 additional methods of restraint .....1.25 → 1.28, 1.31 changing a wheel............
Page 234
AlphAbeticAl index (2/5) driving position front seats settings ............1.22 → 1.24 adjustment ......1.15, 1.17 – 1.18, 1.22 → 1.24 with electric controls ............ 1.19 with manual controls ............ 1.17 electric beam height adjustment ........1.74 fuel electric windows ............3.12 → 3.14 advice on fuel economy ..........
4 SIMPLE ACTIONS* FOR YOUR SAFETY • Always fasten • Always secure children • Adjust the height of • Place heavy objects or your seat belt, using devices suitable the seat belt according luggage at the back of the – even for short journeys for their size and weight to your size.
Page 239
à999105247Rí ú ê ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...