Page 1
REVISIONS - ELECTRICAL PARTS LIST.55 REMOTE CONTROL FUNCTIONS……….17 ELECTRICAL PARTS LIST…….………….56 SERVICE BULLETINS/TECH TIPS…...….20 SEMICONDUCTOR PINOUTS……..….….76 IDLE CURRENT ADJUST…………….…...28 SCHEMATICS…………………..…..……..137 TUNER ALIGNMENT…………………..…..29 AVR7000 TRANSFORMER………..…….161 TROUBLESHOOTING GUIDE…...…….…32 WIRING DIAGRAM………………………..162 PACKAGE……………………...……...…..163 PROCESSOR RESET……………………..32 UNIT EXPLODED VIEW……………………33 harman/kardon, Inc. 250 Crossways Park Dr.
Page 2
AVR7000 harman/kardon Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field effect transistors and semiconductor "chip" components.
Page 3
AVR7000 harman/kardon Before returning the unit to the user, perform the following safety checks : 1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the unit.
Height measurement includes feet and chassis. All features and specifications are subject to change without notice. Harman Kardon is a registered trademark, and Power for the digital revolution is a trademark, of Harman International Industries, Inc. *Manufactured under license from Dolby Laboratories.
AVR7000 harman/kardon DETAILED SPECIFICATION FOR RECEIVER AVR7000 (120V) PARAMETERS Measuring methods are based on IHF and IEC standard 268-3 Measurement conditions,unless otherwise noted : Output resistive load = (8) ohms / All channels loaded. Tone Off or Tone(Bass,Treble), Balance, EQ control : Center Position , Other SW's : OFF, Volume:Max Nominal input level : 200mV for general purpose inputs Power figures should be kept minimum 10min., between 15 and 35...
Page 6
at 0.1% THD, 10 Hz-80 KHz 20 KHz >110 >115 measurement BW.Volume at Max. CONTINUOUS AVERAGE at 0.1% THD, 10 Hz-80 KHz POWER: B) All 5 6 CH DIRECT 20 Hz >100 >105 measurement BW.Volume at Max. Channels Driven, 8 ohms at 0.1% THD, 10 Hz-80 KHz 6 CH DIRECT 1kHz...
Page 7
Volume at Max. Apply Sinewave Signal Gen amplitude to the tested All Analog input, to obtain R/O-3dB at the speaker Stereo and 6 CH 10 kHz outputs. Record the FL and FR speaker > 55 >75 DIRECT Inputs output level as the reference output. Scroll thru other stereo inputs, and measure the output level.
Page 9
AVR7000 harman/kardon TUNER SECTION Measuring methods in confirmity with IEC standard 315 Measurements condition FM : Radio frequency = 98.1MHz, Audio frequency = 1kHz Reference level = 1mV on ( 75ohms , 300ohms ) Deviation : MONO = ?5kHz, Stereo = ?7.5kHz?.5kHz MONO = ?0kHz, Stereo = ?0kHz?.5kHz...
Page 10
S/N RATIO > 40 > 45 INPUT=10mV/m TOTAL HARMONIC DISTORTION > 1.5 > 0.8 OVER LOAD DISTORTION 5mV 80% MOD > 10 > 5 FREQUENCY RESPONSE at -6dB 100~2K 80~2.3K SELECTIVITY 10kHz/9kHz > 20 > 25 AGC FIGURE OF MERIT INPUT 100mV >...
Page 11
AVR7000 harman/kardon Measurements conditions,unless otherwise noted : Input Function : DVD Digital Input Mode : OPTICAL1 AC-3 SECTION Speker Mode : Front/Center/Surround:LARGE, Sub-Woofer:YES Main Vol Position : 1 Vrms Output Position Trim Vol Position : All "0 dB" Test Point : Pre-Out Test disc : DOLBY TEST DVD VERSION 1.0...
Page 12
AVR7000 harman/kardon DIGITAL(AC3) Section L/C/R/Ls/Rs/LFE - Main Vol level 30Hz 15 < +/- 2 15 < +/- 1 >Sub Out C/Ls/Rs/LFE -> "60" Position 30Hz -6.5 < +/- 3 -6.5 < +/- 2 L, R :Sub: No Main Vol Level : -22 <...
AVR7000 harman/kardon Front Panel Controls ˆ ı Ù Û Ú Ò Ô Ó & @ # $ % 1 Main Power Switch ! Input Source Selector Ô Delay 2 System Power Control @ FM Mode Selector Digital Input Selector 3 Power Indicator # Bass Control Ò...
Page 14
AVR7000 harman/kardon Front Panel Controls 7 Surround Mode Selector: Press this but- In normal use, they are an input that may be Digital Input Selector: When playing a selected by pressing the Input Source source that has a digital output, press this...
AVR7000 harman/kardon Rear Panel Connections · ° ‡ fl fi › ¡ ™ £ ¢ ∞ § ¶ • ª ‚ ⁄ ¤ ‹ ¡ AM Antenna ⁄ Amplifier Inputs b Multiroom IR Input ™ FM Antenna ¤ Unswitched AC Accessory Outlet c Remote IR Input £...
Page 16
IR sensor in the receiver to serve other information on speaker polarity.) remote controlled devices. Connect this jack to the “IR IN” jack on Harman Kardon or other ‚ Tape Outputs: Connect these jacks to the compatible equipment.
AVR7000 harman/kardon Main Remote Control Functions a Program Indicator b AVR Selector c CD/Tape/DVD Input Selectors d Power Off Button e Test Tone f Mute Buttons ⁄ ¤ h Channel Select Button harman kardon i Set Button Button ‹ k Digital Select TAPE l 6-Ch.
AVR 7000 and most Harman Kardon CD or DVD process. (See page 34 for more information on step increments. When the FM band is in use, players and cassette decks.
Page 19
AVR7000 harman/kardon Main Remote Control Functions w Preset Up/Down: When the tuner is Delay/Prev Ch.: Press this button to Volume Up/Down: Press these buttons to begin the process for setting the delay times in use, press these buttons to scroll through the raise or lower the system volume.
Page 20
Models: AVR7000 Subject: Video Signal, Color Shift In the event you receive an AVR7000 receiver with the complaint “when the video signal is routed through my AVR7000, there is a noticeable color shift with certain program material”, perform the following modification: 1.
Page 21
Subject: Noise in Logic 7 Mode In the event you receive an AVR500 or AVR7000 receiver with the complaint “There is crackling, noise, or distortion coming from my loudspeakers when my receiver is in the Logic 7 mode with certain program material playing”, perform the following procedure:...
Page 22
13) Test unit by powering up the receiver and playing a music source in the Logic 7 mode. AVR7000 ONLY: MODIFICATION OF THE DSP BOARD (replace IC101 AT27LV020A) WARNING: FOLLOW PROPER STATIC CONTROL PROCEDURES and use caution during the installation of new IC101 to prevent damage.
Page 23
3) Replace the top cover. 4) Test the Switched AC Accessory Outlets by connecting a low power device, such as a CD player, DVD player, or Tape Deck and assure the unit powers up normally when the AVR7000 System Power Control is switched on.
Page 24
Loosen (do not remove) the 2 remaining bracket support screws at the bottom of the bracket, at the bottom of the AVR7000 chassis; you should now be able to push the bracket back far enough to be able to remove both the Video and DSP PCB’s when necessary.
Page 25
AVR7000 harman/kardon g) Disengage the Video PCB from its rear connector (CP601) by pushing back on the rear PCB; lift the Video PCB up and out of the unit. It should still have an amber-colored 8 pin connector attached. Set the PCB aside and out of the way.
Page 26
For models: AVR7000 TIP# HKTT2000-01 Complaint: The Remote Control has stopped working for the AVR7000. First Check: 1. Make sure the batteries in the remote are installed correctly. (Plus and minus to correct terminals) 2. Make sure the area between the remote control and receiver is not blocked by some object, and the distance is no more than 15 feet at an angle no greater than 30 degrees from the front of the receiver.
AVR7000 harman/kardon TECH TIPS harman/kardon Troubleshooting tips and solutions to common service problems TIP# HKTT2003-01 Rev5 For models: AVR7000/7200/7300/8000 AVR10 AVR100/200/300/500 DPR1001 AVR110/210/310/510 DPR1005 AVR120/220/320/520 DPR2005 AVR125/225/325/525 HK3370/3470/3375/3475 AVR130/230/330/430/630 HK3250 AVR135/235/335/435/635 Subject: Backup Memory on AVR/DPR/HK series receivers In the event of the complaint: “the receiver is losing its memory (any programmed system settings) when the unit is turned off, or after the unit is unplugged (briefly*)”:...
Page 28
AVR7000 harman/kardon AVR7000 IDLE CURRENT ADJUSTMENT 1) 2-CH AMP and 3-CH AMP sections should be adjusted when they are intact on the Heat-sink 2) Initial warm-up and test condition: 1Khz - Signal input, SPKR-OUT(8ohm load), 5CH All driven 3) Warm up 3 minutes in step 2, then remove input signal 4) Emitter resistors - connections across MPR901,904, MPR907,910,913 as follows: adjust voltage to 26mV ±...
AVR7000 harman/kardon AVR700 TUNER ALIGNMENT • Europe Mono 40kHz Stereo 67.5kH 1.Electrical specificat • America Mono 75kHz Stereo 40kHz SPECIFICATION ITEMS Above the receiving Frequency Local OSC •522 ~ 1620kHz •87.5 ~ 108.0MHz Frequency cover r •520 ~ 1720kHz •87.5 ~ 107.9MHz Standard supply v 15.0 (+/-1.5V)
Page 30
AVR7000 harman/kardon AVR700 TUNER ALIGNMENT (con't) Europe Mono 40kHz Stereo 67.5kHz Pilot 7 1.Electrical speci America Mono 75kHz Stereo 40kHz Pilot 7.5k SPECIFICATION ITEMS Above the receiving Frequency Local OSC •522 ~ 1620kHz •87.5 ~ 108.0MHz Frequency cover ra •520 ~ 1720kHz •87.5 ~ 107.9MHz...
Light around power switch is red due to possible short speaker ends • Amplifier is in protection mode • Contact your local Harman Kardon service depot due to internal problems No sound from surround or • Incorrect surround mode • Select a mode other than Stereo center speakers •...
Page 52
AVR7000 harman/kardon AVR7000 MECHANICAL PARTS LIST J5541001020X WASHER FLAT J2822110014X*POWER TRANS 120/60 J2822410014X*POWER TRANS 230/50 JE99005307EA MNBD ASM 7000RDS J43730100200*CORD AC POWER JE99005307UA MNBD ASM AVR7000 J43731100200*CORD AC POWER RDS JE99005507EA FRBD ASM 7000RDS J43732100200*CORD AC POWER SG JE99005507UA FRBD ASM AVR7000...
Page 53
AVR7000 harman/kardon 13 01201 M85100009000 KNOB TONE HIPS RAW 1.00000 M F5299 02 --------------------------------------------------------------------------------------------- 0240 J85200049000 BUTTON POWER HIPS F4799 13 02401 M85200049000 BUTTON POWER HIPS 1.00000 M F5299 02 02406 20289980XX DILUTION IPI-783 3 LI .00001 B F4799 ---------------------------------------------------------------------------------------------...
Page 54
J97100506000 CARD-POST J94100001000 JUMPER J97000501000 POLY BAG PE T0.05 J97000501010 AC CORD POLY BAG J97100000000 POLY SHEET PE-FOAM J97200006000 PAD SIDE AVR7000 J97300001000 PAD UPPER AVR7000 J97300002000 PAD INNER AVR7000 J90200002000 MANUAL AVR-7000 J90200002001 MANUAL 7000RDS J96000010001 BOX CARTON 7000RDS 1...
Page 55
Change IC CPU CXP82860-170Q QFP100 to CXP82860-196Q QFP100 CPU upgrade 7-Nov-00 SONY Replace fuse SB 1A/125V with fuse SB 3.15A/125V IN AVR7000 US AC outlet fuse burning issue 7-Nov-00 Change RSR947,976 AND RR946,947 to RES 12GS 39 1/2W 5% For improve S/N ratio...
Page 56
AVR7000 harman/kardon AVR7000 ELECTRICAL PARTS LIST MAIN PCB Part# Ref. Description Part# Ref. Description Designator Designator C506 J3640104350X CP MET .1U 250V -M C577 J3470110071X CE SG 10U 50V M C507 J3640104350X CP MET .1U 250V -M C578 J3470110071X CE SG 10U 50V M...
Page 57
AVR7000 harman/kardon Q502 J2021000601X TR PNP MPSA56 Y R570 J3003222220X RES CF 2K2 1/8W J Q503 J2021020801X TR MPSA06 Y TO-92 R571 J3003153220X RES CF 15K 1/8W J Q504 J2021000601X TR PNP MPSA56 Y R572 J3003153220X RES CF 15K 1/8W J...
Page 58
AVR7000 harman/kardon GND50 J4200020000X GND PLATE C761 J3600473330X CP .047U 100V K IC501 J2110505006X IC KIA7815P C762 J3600473330X CP .047U 100V K IC502 J2112505018X IC KIA7915PI TO220 Q722 J2021220102X TR NPN DTC114YSA IC503 J2110505002X IC KIA7805P Q723 J2021220102X TR NPN DTC114YSA...
AVR7000 harman/kardon 8-channel analog multiplexer / demultiplexer BU4051BC / BU4051BCF / BU4051BCFV The BU4051BC, BU4051BCF and BU4051BCFV are analog multiplexers / demultiplexers which use three-input digi- tal signals for control via an 8-channel analog switch. These products feature high on / off output voltage ratio and low crosstalk between analog switches.
Page 88
AVR7000 harman/kardon Triple 2-channel analog multiplexer / demultiplexer BU4053BC / BU4053BCF / BU4053BCFV The BU4053BC, BU4053BCF, and BU4053BCFV are multiplexers / demultiplexers capable of selecting and combin- ing analog signals and digital signals in a 2 ch × 3 configuration. Inhibit signals and control signals are used to turn on the switch corresponding to each of the channels.
Page 89
AVR7000 harman/kardon 8-bit compatible shift / store register BU4094BC / BU4094BCF / BU4094BCFV The BU4094BC, BU4094BCF, and BU4094BCFV are shift / store registers, each consisting of an 8-bit register and an 8-bit latch. As the data in the shift register can be latched by an asynchronous strobe input, it is possible to hold the output in the data transfer mode.
Page 99
AVR7000 harman/kardon M54HCU04 M74HCU04 HEX INVERTER (SINGLE STAGE) HIGH SPEED = 5 ns (TYP.) AT V = 5 V LOW POWER DISSIPATION = 1 µA (MAX.) AT T = 25 C HIGH NOISE IMMUNITY = 10 % V (MIN.) OUTPUT DRIVE CAPABILITY...
Page 116
AVR7000 harman/kardon AK5352 96kHz Sampling ∆Σ 20bit ADC GENERAL DESCRIPTION The AK5352 is a 20-bit, 96kHz sampling rate for DAT and DVD, 64x oversampling rate(64fs), 2-channel A/D ∆Σ converter for stereo digital systems. The modulator in the AK5352 uses the new developed Enhanced Dual bit architecture.
Page 117
AVR7000 harman/kardon Ordering Guide ∼ °C AK5352-VF 24pin VSOP AKD5351/2 Evaluation Board Pin Layout Replacement from AK5350 to AK5352 AK5350 AK5352 Package 28VSOP 24VSOP *)Interchangeable with AK5352 fc of HPF(@fs=48kHz)
Page 118
AVR7000 harman/kardon [AK5352] PIN/FUNCTION Pin Name FUNCTION AINR+ Right channel analog positive input pin AINR- Right channel analog negative input pin VREF Voltage Reference output pin (VA-2.6V) Normally connected to VA with a 0.1uF ceramic capacitor in parallel with a 10uF electrolytic capacitor.
Page 119
AVR7000 harman/kardon ASAHI KASEI [AK5352] SDATA Serial Data Output pin Data are output with MSB first, in 2's complement format. After 20 bits are output it turns to "L". It also remains "L" at a power-down mode(PD="L"). CMODE Master Clock Selection pin "L": MCLK=256fs...
Page 131
AVR7000 harman/kardon 3-channel 75Ω driver BA7660FS The BA7660FS is a 75Ω driver with a 6dB amplifier and three internal circuits, and provides 75Ω drive of composite Y signals and C signals, as well as RGB signals. Each load is capable of driving two circuits, and a sag correction function reduces the capacitance of the output coupling capacitor.
Page 133
AVR7000 harman/kardon Multimedia ICs BA7660FS • Pin descriptions and input / output circuits Reference Pin. No Pin name Equivalent circuit Function voltage Muting control MUTE — — If MUTE (pin 1) is set to HIGH, muting is carried out simultaneously on all three channels.