Residual Risks; Hints For Optimum Use - Black & Decker KTW750 Owner's Manual

Vacuum Adaptor (Figure 10)
@ WARNING: Turn off and unplug the tool before making
any adjustments or removing or installing accessories.
a. Slide the vac adaptor (J) over the chip discharge chute
(F).
b. Connect a vacuum cleaner hose (not included) to the
adaptor.
c. To prevent chips from coming out opposite side of chip
discharge chute, move chip deflector lever (G) to the
opposite side of the adaptor.
To Change Blades (Figure11)
@ WARNING: Turn off and unplug the tool before making
any adjustments or removing or installing accessories.
@ WARNING: Cut Hazard. Planer blades are sharp and
must be handled with care.
NOTE: The KTW750 has two blades, one on each side of the
blade drum. Any operation or adjustment should be made to
both blades.
To Remove Blade (Figure 11)
a. Remove the three bolts (11a) with the wrench (K) supplied.
b. Remove drum cover (11b) and remove the blade (L) out of
its holder.
c. Place the blade or replaced it.
To Reinstall Blade
a. Replace the drum cover (11b). Make sure that the blade is
flush with the planing shoe.
b. Tighten the three bolts (11a) .
@ Always replace both blade.
Parking Foot (Figure 12)
Your planer is equipped with a parking foot (O) that
automatically lowers into place when the tool is lifted from the
work surface. When planing, the parking foot raises as the tool
is pushed forward. When the parking foot is lowered, the
planer can set on the work surface without the blade touching.
@ CAUTION: Do not lock the trigger switch on and engage
the parking foot. The vibration of the running motor will cause
the planer to move, possibly falling from the work piece.
Drive Belt (Figure 13)
WARNING: Turn off and unplug the tool before making
any adjustments or removing or installing accessories.
To Replace Belt
a. Loosen the three screws shown in figure 13 and remove
the belt cover.
b. Remove old belt.
c. Place new belt over front pulley then rotate belt clockwise
while pushing belt onto back pulley.
d. Attach belt cover and securely tighten screws.
Adjusting cutters (Figure 14)
a. Place the blade (L) on the adjust plate (M),and make the
blade edge perfectly flush with the inside edge of the
adjust plate (M).
b. Place the bracket (11d) on the blade and make the flange
of bracket flush with the back side of the adjust plate.
c. Tighten the two screws (11c) on the bracket.
d. Slip the flange of the bracket into the groove of drum
(11e).place the drum cover (11b) and tighten the three
bolts (11a).
Sharpening blades (Figure 15)
a. Fasten the blades to sharpening holder (N). Be sure both
blades edges face in the same direction.
b. Place the blades edges so that they rest flat on the
grinding stone.
c. Firmly grip the sharpening holder and move back and
forward to sharpen the blades (L).

Residual risks

Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
Injuries caused by touching any rotating/moving
u
parts.
Injuries caused when changing any parts, blades or
u
accessories.
Injuries caused by prolonged use of a tool. When
u
using any tool for prolonged periods ensure you take
regular breaks.
Impairment of hearing.
u
Health hazards caused by breathing dust developed
u
when using your tool (example:- working with wood,
especially oak, beech and MDF.)
Use
Warning! Let the tool work at its own pace. Do not overload.
Adjust the depth of cut.
u
If necessary, fit and adjust the parallel fence.
u

Hints for optimum use

Move the tool along the grain of the wood.
u
If the grain is cross or curly, or if the workpiece material is
u
a hard type of wood, adjust the depth of cut to take only
a very thin shaving at each pass and take several passes
to achieve the desired result.
To keep the tool in a straight line, press down the front of
u
ENGLISH
9