Fetco CBS-2152XTS User Manual page 8

GENERAL
Tank Temp.
Brew at Temp.
Units of Meas.
ECO Mode
Logo Timeout
Brew B. Sensor
Use Flowjet
Normal for most water
LLC Sensitivity
"HIGH" for R.O.
BREW AT TEMPERATURE DEFINITONS
BREW AT TEMP: "ON"
(DEFAULT: FACTORY PROGRAMMED INTO BREWER)
"BREW START" Batch Section Buttons will not be accessible until
tank temperature is at set point.
The "BREW START" screens with the Batch Section Buttons
become accessible when hot water tank is at the selected
temperature. The screen at right displays when the "BREW AT
TEMP" is selected.
BREW AT TEMP: AUTO
This allows the "BREW START" to activate if the hot water tank is
at the selected temperature—then brew will start.
If the temperature is too low, the brewer will wait until the proper
temperature is reached. A screen (example to the right) will
display showing a thermometer icon and the tank temperature.
IMPORTANT: ALWAYS have dispenser(s) under the brew
baskets when in the BREW AT TEMP mode.
OFF
BREW AT TEMP:
Allows brewing at any temperature above 179°F/82°C.
May NOT apply for two sided brewer if one side is in brew cycle
Programming
INPUTS
• Input Summery
Display Inputs
Cal. Touch Scr
Programming Factory set
Items
200°F
"OFF" allows
"ON"
brewing at any
temperature.
• Temperature
°C or °F
• Volume
Gallons [Liters]
Energy Saving
OFF
Mode
0:30 mm:ss
NORMAL
NO
NORMAL
USER SELECTABLE
USER SELECTABLE
Factory set
Items
Calibrate
Programming Range
Default
|______________[]___|
170
|________[]_______|
OFF
|___[]____________|
|___[]____________|
_______________[]_____
0:15
|__[]____________|
NORMAL
____[]_______________
____[]______________
NORMAL
XTS
™
EXTRACTOR
TOUCHSCREEN
CBS_2132 3L
Ready Tank Temp °F
197
Heating
Filling
XTS
Regular 1
1.50
INFO
05:30
Regular 2
1.50
05:30
Decaf 1
92°
1.50
05:30
C
Decaf 2
STOP
1.00
05:30
(Not recommended)
Programming Range
Default
R. Brew Basket Sens. [ single/dual]
L. Brew Basket Sens.
H. Liquid Level probe
H. Tank Temperature Probe
L. Tank Temperature Probe
SD Card Recognized
Tank Temp.
________________[]____
8
(display)
200 °F
207
ON
ON AUTO
°F
°F °C
Gallons
Gallons Liters
ECO Mode
ON OFF
0:30 mm:ss
|__[]___________|
5:00
NORMAL
OVERRIDE
NO
NO YES
NORMAL
HIGH
Chart to correct for altitude for boiling point
in tank water temperature.
Suggested
[ft] [m]
Setting[°F]
0 0 200
500 152 200
1000 305 200
2000 610 200
2500 762 200
3000 914 200
3500 1067 197
4000 1219 195
4500 1372 194
5000 1524 194
5500 1676 193
6000 1829 192
6500 1981 191
7000 2134 190
7500 2286 188
8000 2438 187
8500 2591 185
(display)
200
Calibrate
YES NO
Notes
Correction for high
altitude below
SEE NOTE BELOW!
[Switchable Units]
[Switchable Units]
If Selected: Lowers hot
water tank temperature to
170°F after 1 hour of
inactivity
Factory or service use for
servicing. "NORMAL" is
recommended for safety.
Trims water handling
system for Flowjet
Sets sensitivity for liquid level
control.
High is for reverse osmosis
water or very pure water.
Boiling Suggested Boiling
point[°F] Setting[°C] point [°C]
212.0 93 100.0
211.0 93 99.5
210.1 93 98.9
208.1 93 97.8
207.2 93 97.3
206.2 93 96.8
205.3 92 96.3
204.3 91 95.7
203.4 90 95.2
202.4 90 94.7
201.5 89 94.2
200.6 89 93.6
199.6 88 93.1
198.7 87 92.6
197.8 86 92.1
196.9 86 91.6
196.0 85 91.1
Notes
If Yes:
Follow directions on the
touch screen