Page 1
Quick Installation Manual LED GSM Wireless Alarm System By shield4u http://www.usmartbuy.com (Version 20120827) www.usmartbuy.com...
Page 2
A. Alarm Understanding Away Disarm Home Emergency www.usmartbuy.com...
Page 3
Function Signal Interpretation Short “Beep” twice Error in command or failed operation Buzzer Successful in command or successful Long “Beep” once or twice operation Defense Zone Always lit Defense zone alerting All Alarm LED Always lit Arming status Part Alarm LED Always lit Home arming status Emergency alarm...
Page 4
Connect the indoor strobe siren to the power socket and then wait 10 seconds for the initialization Press and hold the “Learn” button at the side of the indoor siren for about 15 seconds and all lights flash once ...
Page 5
Press down the green button at the back of outdoor siren Press red button at the back of outdoor siren and all lights on (not only power LED) Press key on the host and alarm host goes off ...
Page 6
and 10) and press 【ENT】 ”Learn” LED lights up use magnet contact to trigger the sensor twice successively when hear long “Beep” from the control host and see the “Learn” LED flashes and then off, this means the sensor learning is successful After that please turn off registered sensor and start from again to register another sensor.
Page 7
Please note: all sensors registered on that zone will be deleted. 2. Indoor siren Plug the indoor siren into the power Press down and hold the learning button at the side for 15 seconds and release the LED in the siren flashes once.
Page 8
F. Preset Phone Numbers into the Control Host 【0】 X 【ENT】 “Telephone number” 【ENT】 Y 【ENT】 Command: Where “X”: Phone number group number, can be 1~6; “Y”: 0 or 1. (“0”: phone call alert; “1”: SMS message alert) You can store 6 phone numbers. Group 1 and 2 are for monitoring centres and other 4 groups are for personal numbers.
Page 9
ii) By keypad on the control host: Press 【ESC】 and enter password Press 【ENT】 the control host will beep twice to successfully complete the operation I. Phone long-distance-control 1. Call-in to control Dial the phone number associated to the SIM card which in the control host through telephone or cellphone. After a cycle of ringing, the control host will pick up the call.
Page 10
J. Alarm Setting Command: Before operating the alarm function setting commands in Table below, user needs to make sure the control host has entered into the program status. How to enter into the program status: Make sure the control host is in disarmed status and Press 【SET】 ...
Page 11
K. How to Change Alarm Password 【SET】 ”Programming” LED light up (if it does not light up, please press ESC button first and then press SET button again) 999999 【ENT】 Six Digital New Programming Passwords 【ENT】 Six Digital New Programming Passwords ...
Page 12
Installation and Usage: For users to take along. Generally, press the “Away” key to arm before leaving home; and press the “Disarm” key to disarm; “Home” is for “Home Arming”, “Home Arming” is only effective for sensors in Perimeter Zone Wireless Door Sensor Features: ...
Page 13
Suggestion: Generally around 1.8M from the ground How to reset/unregister: Plug the indoor siren into the power Press down and hold the learning button at the side for 15 seconds and release the LED in the siren flashes once.
Page 14
Alarming volume:≥110db Installation and usage: Press down the green power switch at the back after connecting the siren to the AC power Study the siren to the alarm host according to the instruction Unplug from the AC power, fix it in the proper outdoor place with handing hook, and then plug to...
Page 15
Repeatedly receiving the alarm Fail to operate according to the Follow the instructions after answering the telephone operation instruction of the telephone alarm phone calls and hearing the recorded alarm message Can’t receive alarm SIM card is not insert properly ...
Need help?
Do you have a question about the LED GSM and is the answer not in the manual?
Questions and answers