4. Secondary handle
5. Handle knob
6. Handle adjustment collar
7. Mode adjustment collar
8. Motor housing
10. Line trimming blade
11. Edge guide
12. Spool housing
13. Cutting line
16. Charging indicator
17. End of charge indicator
Warning! Before assembly, remove the battery from the tool.
Fitting and removing the battery (ﬁg. B)
To ﬁt the battery (14), line it up with the receptacle on the
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release button (18) while
at the same time pulling the battery out of the receptacle.
Fitting the guard (ﬁg. C)
Warning! Never operate the tool with damaged guards or
shields or without guards or shield in place.
Place the guard (9) onto the tool as shown, aligning the
holes (19) with the lugs (20) on the tool.
Press the guard until it snaps into place (A).
Push the guard forward (B).
Securely tighten the screws (21).
Warning! Never use the tool unless the guard is properly ﬁtted.
Fitting a new spool of cutting line (ﬁg. D)
Replacement spools of cutting line are available from your
Black & Decker dealer (cat. no. A6481).
Keep the tabs (22) on the spool cover (23) depressed and
remove the spool cover from the housing (12).
Remove the empty spool (24) from the housing.
Remove any dirt and grass from the housing.
Take the new spool and unwind approx. 12 cm of cutting line.
Feed the cutting line through the eyelet (25).
Push the spool onto the drive shaft (26) and rotate it
slightly until it is seated. Make sure that the cutting line is
not trapped under the spool and that 10-12 cm of cutting
line protrudes from the housing.
Align the tabs on the spool cover with the holes in the housing.
Push the cover onto the housing until it snaps into place.
Warning! If the cutting line protrudes beyond the trimming
blade (11), cut it off so that it just reaches the blade.
Winding new line onto an empty spool (ﬁg. E - G)
You may wind new cutting line onto an empty spool.
Replacement packs of cutting line are available from your
Black & Decker dealer (cat. no. A6170 (25 m), A6171 (40 m)).
Remove the empty spool from the tool as described above.
Remove any old cutting line from the spool (27) (ﬁg. E).
Feed 2 cm of cutting line into one of the holes (28) in the
spool as shown (ﬁg. F).
Bend the cutting line and anchor it in the L-shaped slot (29).
Wind the cutting line onto the spool in the direction of the
arrow. Make sure to wind the line on neatly and in layers.
Do not criss-cross (ﬁg. G).
When the wound cutting line reaches the recesses (30),
cut the line. Let the line protrude approx. 12 cm from the
spool and hold a ﬁnger on the line to keep it in place (ﬁg. E).
Proceed as described above to ﬁt the spool on the tool.
Warning! Only use the appropriate type of Black & Decker
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (ﬁg. A)
The battery needs to be charged before ﬁrst use and whenever it
fails to produce sufﬁcient power on jobs that were easily done
before. When charging the battery for the ﬁrst time, or after
prolonged storage, it will only accept an 80% charge. After several
charge and discharge cycles, the battery will attain full
capacity. The battery may become warm while charging; this
is normal and does not indicate a problem.
Warning! Do not charge the battery at ambient temperatures
below 4 °C or above 40 °C. Recommended charging
temperature: approx. 24 °C.
To charge the battery (14), remove it from the tool and
insert it into the charger (15). The battery will only ﬁt into
the charger in one way. Do not force. Be sure that the
battery is fully seated in the charger.
Plug in the charger.
8 hour charger
The battery will be fully charged in approx. 8 hours. It can be
removed at any time or left in the connected charger indeﬁnitely.
1 hour charger
Check if the red charging indicator (16) lights up. If the
green end of charge indicator (17) lights up now instead,
the battery is too hot and cannot be charged. If this
happens, remove the battery from the charger, let the
battery cool down for approx. 1 hour and re-insert it.