Washer Care; Cleaning Your Washer; Water Inlet Hoses; Assistance Or Service - Whirlpool CGD9060 Installation Instructions Manual

Commercial front-load washer
Table of Contents

Advertisement

Available languages

Available languages

Cleaning Your Washer

Cleaning the Door Seal/Bellow
1. Open the washer door and remove any clothing or items
from the washer.
2. Inspect inner glass door. If debris is present, wipe off debris
using damp cloth.
3. Inspect the colored seal/bellow between the door opening
and the drum for stained areas. Pull back the seal/bellow
to inspect all areas under the seal/bellow and to check
for foreign objects.
A. Seal/Bellow
4. If stained areas are found, wipe down these areas of the seal/
bellow, using the procedure that follows:
a)
Mix a dilute solution, using 3/4 cup (177 mL) of liquid
chlorine bleach, and 1 gal. (3.8 L) of warm tap water.
b)
Wipe the seal/bellow area with the dilute solution,
using a damp cloth.
c)
Let stand 5 minutes.
d)
Wipe down area thoroughly with a dry cloth and let
the washer interior air dry with door open.
IMPORTANT:
Wear rubber gloves when cleaning for prolonged periods.
I
Refer to the bleach manufacturer's instructions for proper use.
I
Washer Maintenance Procedure
This washer has a special cycle that uses higher water volumes
in combination with liquid chlorine bleach to thoroughly clean
the inside of the washer.
NOTES:
Read these instructions completely before beginning
I
the cleaning process.
If necessary, the cleaning cycle may be interrupted by
I
pressing the COLD button twice. However, this will not
immediately stop the cycle. The washer will continue with
several rinse and drain steps to ensure that all remaining
bleach is rinsed from the washer.
Begin procedure
1. Open the washer door and remove any clothing or items
from the washer.
2. Use liquid chlorine bleach:
Open the dispenser drawer and immediately add
2/3 cup (160 mL) of liquid chlorine bleach to the bleach
compartment.
NOTE: Do not add any detergent to this cycle. Use of more
than 2/3 cup (160 mL) of bleach will cause product damage
over time.

WASHER CARE

A
3. Close the washer door and the dispenser drawer.
4. To start the Clean Washer cycle, rst enter "Start Operating
Set-up." Then press and hold COLD for 1 second. With
the entire display ashing, press COLORS/DELICATES.
NOTE: The drum will rotate, then the door will unlock,
lock again, and then the cycle will continue.
The washer will not ll, but the drum will rotate while
I
the washer runs a short sensing cycle. This will take
approximately 3 minutes.
5. The cycle will determine whether clothing or other items are
in the washer.
a)
If no items are detected in the washer, it will proceed
to Step 7.
b)
If any items are detected in the washer, "rL" or "F-34"
will be displayed. Then the door will unlock.
Press COLD to cancel the failure code. Then repeat
I
steps 1, 3, and 4 to start the cycle again.
6. Once the cycle has begun, allow the cycle to complete.
7. After the cycle is complete, leave the door open slightly,
to allow for better ventilation and drying of washer interior.
Always do the following to maintain washer freshness:
Use only "HE" High Ef ciency detergent.
I
Leave the door slightly open after each cycle to allow
I
for better ventilation and drying of washer interior.
Clean the washer monthly using the Washer Maintenance
I
Procedure, and 2/3 cup (160 mL) of liquid chlorine bleach.
If the procedure does not suf ciently improve the washer
I
freshness, please evaluate your installation and usage
conditions for other causes.
Cleaning the exterior
Use a soft damp cloth or sponge to wipe up any spills.
Occasionally wipe the outside of your washer to keep it looking
new. Use mild soap and water. Do not use abrasive products.
Cleaning the dispenser drawer
The dispenser drawer is removable for easy cleaning.
1. Unlock the dispenser drawer by pressing the Release Lever.
Remove the drawer.
2. Remove the inserts (the siphon from the softener and bleach
compartments).
3. Wash the parts under running water.
NOTE: Do not wash components in the dishwasher.
4. Re-install the inserts and return the dispenser to the drawer.

Water Inlet Hoses

Replace water inlet hoses after 5 years of use to reduce the risk
of hose failure. Periodically inspect and replace water inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your water inlet hoses, mark the date
of replacement on the label with a permanent marker.

ASSISTANCE OR SERVICE

If you need assistance:
Contact the distributor where the washer was purchased from
or visit www.whirlpoolcommerciallaundry.com.
When you call, have the washer model number and serial
number. Both numbers can be found on the serial-rating plate
located on your washer.
13

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ced9050Chw9060Chw9050Cgd9050Ced9060

Table of Contents