Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Heatmiser PRT-W
Summary of Contents for Heatmiser PRT-W
-
Page 1: Operating Instructions
Operating Instructions Model: PRT-W REF: PRT-W Revision 1 11/11... - Page 6 Pages 17-24 explain the different features available on this thermostat. Pairing with the RC1-W Receiver If using with the UH1-W wiring centre, turn to page 6. With the thermostat turned off: • Press & hold the Clock button until you see two sets of numbers appear.
-
Page 7: Pairing The Thermostat
You are able to connect two PRT-W thermostats to one RC1-W receiver. You should now use the up/down buttons to select which zone this thermostat controls, 01 or 02. • Press A to accept, the display will now go blank. - Page 8 Pairing with the UH1-W Wiring Centre On the UH1-W wiring centre, take note of the number set on the rotary switch (Board ID number 1-9). Each UH1-W on the system will need a different ID number. With the thermostat turned off: •...
- Page 9 • Use the Up/Down keys & set the large digits to the board address of the UH1-W, this is the number set on the UH1-W rotary switch. (You should set a unique board address on each UH1-W installed). • Press Clock again until you see feature 08 (Zone Number, 01-08).
- Page 10 He ng On He ng Off – Frost Mode Key Lock RF Signal Ac ve Ba ery Holiday Ac ve...
- Page 11 • • • • •...
- Page 12 • • • • •...
- Page 13 Comfort Levels Explained The Heatmiser PRT-W provides Weekday/Weekend or 7 Day programming. You should consult the Configuration Menu section to select the required mode. The thermostat is supplied with comfort levels already programmed, but these can be changed easily. The default times are: 08:00 –...
- Page 14 • To begin programming the comfort levels, press Clock Once • If your thermostat is setup for Weekday/Weekend programming, you will see Mon-Fri shown. For 7 day programming you will see Monday, you need to use Up/Down arrow keys to select which day you would like to program and then press H key to confirm.
- Page 15 • • • • •...
- Page 17 The Heatmiser PRT-W has a holiday function. This allows you to • • •...
- Page 18 • •...
- Page 20 Feature 04 – Frost Protect Temperature: This is the temperature maintained when the thermostat is in frost mode. The range is 07-17°C. The default is 12°C and is suitable for almost all applications. Feature 05 – Output Delay: To prevent rapid switching, and output delay can be entered.
- Page 21 Feature 08 – Zone Number: This is the zone number you are assigning the thermostat to on either the UH1-W or the RC1-W receiver. 01-08 - UH1-W, 01-02 – RC1-W Feature 09 – Underfloor Heating or Radiator Zone (UH1-W Only): This setting determines whether the thermostat will activate the pump &...
- Page 22 Feature 11 – Up/Down Temperature Limit: This function allows you to limit the use of the up and down temperature keys. This limit is also applicable when the thermostat is locked and so allows you to give others limited control of the heating system. Feature 12 –...
- Page 24 01-03C 01C Default...
- Page 25 Frost Temperature 07-17C (12C Deafult) Output Delay 00-15 Minutes (00 Default) UH1-W or RC1-W 00 = UH1-W Receiver 01 = RC1-W 00 = Default Receiver Board UH1-W = 01-09 Address RC1-W = 01-32 00 = Default Zone Number UH1-W - 01-08 RC1-W = 01-02...
- Page 26 Underfloor Heating or Underfloor Heating = Radiator (UH1-W Only) Radiator Zone = 01 Fail Safe 00 Disabled 01 Enabled (00 Default) Up/Down Limit 00-10C 00C Default Sensor Selection 00 = Built in sensor 01 = Remote air sensor Not used Not used Preheat Setting 00-03 hours...
Need help?
Do you have a question about the PRT-W and is the answer not in the manual?
Questions and answers