Table of Contents
Advertisement
OIL-FIRED CENTRAL FURNACE
Installation, Operation, and Service Manual
VHF-ABE
VHF-ANE
• Do NOT store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.
• Improper
maintenance can cause a fire or explosion resulting in property
damage, personal injury, or loss of life. For assistance or additional
information consult a qualified installer or service agency.
These instructions should be:
• read prior to installing the furnace
• retained for reference by qualified service personnel
• reviewed before performing any service or maintenance
MO-450
ECN 5396-MA 141211
With Users Information Section
Models:
c WARNING:
installation,
adjustment,
Thermo Products, LLC
5235 West State Road 10
North Judson, Indiana 46366
VHF-ABP
VHF-ANP
alteration,
service,
MADE IN USA
or
Advertisement
Table of Contents
Related Manuals for Thermo Products Spirit VHF-ABE
Summary of Contents for Thermo Products Spirit VHF-ABE
- Page 1 These instructions should be: • read prior to installing the furnace • retained for reference by qualified service personnel • reviewed before performing any service or maintenance Thermo Products, LLC 5235 West State Road 10 North Judson, Indiana 46366 MO-450...
-
Page 2: Safety Section
The predetermined limit location on this oil fired furnace has been tested and approved by Thermo Products, LLC. Any attempt to relocate this safety control or replace this safety control with a control that is not approved, or is incompatible, may result in personal injury, substantial property damage or death. -
Page 3: Table Of Contents
All installations and services must be performed by qualified service personnel. TABLE OF CONTENTS SECTION BEGINNING PAGE I. SAFETY SECTION II. GENERAL INSTRUCTIONS A. VENTING B. DRAFT REGULATORS C. DUCT WORK/AIR CONDITIONING/SUPPLY/RETURN AIRFLOW AND AIR TEMPERATURE D. FILTERS MOUNTED EXTERNAL TO FURNACE E. -
Page 4: General Instructions
All installations and services must be performed by qualified service personnel. II. GENERAL INSTRUCTIONS - READ BEFORE START OF INSTALLATION 1. The heating output capacity of the furnace proposed for installation should be based on a heat loss calculation made according to the manuals provided by the Air Conditioning Contractors of America (ACCA) or the American Society of Heating, Refrigeration and Air Conditioning Engineers, Inc. -
Page 5: Venting
All installations and services must be performed by qualified service personnel. Power (Side-Wall) Venting-Important Note Regarding cCAUTION: The manufacturer of this furnace will NOT assume responsibility for damage to, and deterioration of, exterior building materials, e.g. brick, siding, clapboards, and etc., in close proximity to the vent terminal due to operation of a power vented, oil furnace. -
Page 6: Draft Regulators
All installations and services must be performed by qualified service personnel. SIDE WALL VENTING APPLICATION ORDER INFORMATION FIELD VENT TERMINATION SIDE WALL VENT COMBUSTION AIR INTAKE ACCESSORIES KIT HOOD KIT (FOR COMBUSTION AIR BURNER (15’ application MAX) (BURNER SPECIFIC) APPLICATIONS ONLY) PART NUMBER PART NUMBER PART NUMBER... -
Page 7: Filters Mounted External To Furnace
All installations and services must be performed by qualified service personnel. The duct system should again follow the current design standard of Air Conditioning Contractors of America (ACCA) or ASHRAE Fundamentals volume.The most common location for the A-shaped coil (A style) is shown in Fig. -
Page 8: Limit Position And Location
The predetermined limit location on this oil fired furnace has been tested and approved by Thermo Products, LLC. Any attempt to relocate this safety control or replace this safety control with a control that is not approved, or is incompatible, may result in personal injury, substantial property damage or death. -
Page 9: Burner Installation
All installations and services must be performed by qualified service personnel. F. BURNER INSTALLATION: NOTE: The burner is factory installed on this furnace. NOTICE: Remove all cardboard packing from around chamber before installing burner. The oil burner will mount on three stud mounting bolts on the lower mounting plate covering the opening in the front of the heat exchanger. -
Page 10: Burner Specifications And Applications
AN 80° SPRAY ANGLE AND A HOLLOW SPRAY PATTERN WOULD BE ABBREVIATED IN THE °A TABLE AS “0.65 X 80 ”. For more specific burner information, contact: Thermo Products, LLC, 5235 West State Road 10 North Judson, IN 46366 INPUT CAPACITY SELECTION CHART EQUIVALENT... -
Page 11: Heat Exchanger Cleaning Instructions
All installations and services must be performed by qualified service personnel. H. HEAT EXCHANGER CLEANING INSTRUCTIONS: cWARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED SERVICE PERSON. It is important to inspect and clean the heat exchanger once a year, or as necessary, to remove any build-up of soot. A layer of soot on the inside of the heat exchanger will act as an insulator and reduce heat transfer, resulting in less efficiency. -
Page 12: Users Information Section
All installations and services must be performed by qualified service personnel. III. USERS INFORMATION SECTION A. OIL SUPPLY: Do not allow the fuel tank to run completely empty. During the summer, keep the tank full to prevent condensation of moisture on the inside surface of the tank. If the fuel tank runs completely dry, it may be necessary to purge the lines of trapped air. -
Page 13: Filter Cleaning And Locations
All installations and services must be performed by qualified service personnel. E. FILTER CLEANING AND LOCATION: The air filters should be inspected each month and cleaned when dirty. Cleaning the air filters frequently may reduce airborne contaminants from entering the furnace and depositing in the furnace, duct system and home. cWARNING: To avoid injury from moving parts, hot surfaces, or electrical shock, shut off the power to the furnace before removing any furnace access doors to service the air filters. - Page 14 All installations and services must be performed by qualified service personnel. COMBUSTION AND EFFICIENCY TESTING FOR OIL FIRED CENTRAL FURNACES. Complete this form for each furnace installed. Read instruction manual carefully before making tests. Retain this form with furnace. furnace. CUSTOMER NAME ADDRESS...
-
Page 15: Appendix-A Replacement Parts List
All installations and services must be performed by qualified service personnel. APPENDIX-A Replacement Parts List... - Page 16 All installations and services must be performed by qualified service personnel.
- Page 17 All installations and services must be performed by qualified service personnel.
- Page 18 All installations and services must be performed by qualified service personnel.
-
Page 19: Appendix-B Wiring Diagrams
All installations and services must be performed by qualified service personnel. APPENDIX-B Wiring Diagrams BLOWER SPEED TAPS COOL = A/C Tap HEAT = Heating Tap LOW = Constant air or Dehumifier... - Page 20 All installations and services must be performed by qualified service personnel.