Bosch WVH28360GB Installation And Maintenance Instructions Manual page 2

Transportation, e.g. when moving house
1. Before transporting the washer dryer:
1. Turn off the tap.
2. Release the water pressure in the supply hose.
Page 8: Filter in the water inlet hose
3. Drain any residual detergent solution.
Page 8: Draining the pump
4. Disconnect the washer dryer from the power supply.
5. Remove the hoses.
2.
Installing transport bolts:
1. Remove the covers.
2. Insert all sleeves.
Clamp the power cord into
the holders.
Insert the bolts and tighten.
The transport bolts must be removed after transportation. Page 3
To prevent unused detergent from flowing into the outlet during the next wash:
Pour 1 litre of water into dispenser II and start the Empty (Drain) or Spin programme.
Technical specifications
Dimensions (width x depth x height) 600 x 590 x 850 mm
Weight 81 kg
Nominal voltage 220–240 V, 50 Hz
Max. current 10A
Power supply
Max. washing power 2400 W
Max. drying power 1900 W
Water pressure 100-1000 kPa (1-10 bar)
Drain height 60–100 cm
According to applicable European Standard
Test programmes
EN50229
6
– Risk of electric shock.
Pull out the mains plug.
Care
– Risk of explosion. No solvents.
Machine housing, control panel
– Wipe with a soft, damp cloth.
– Do not use any abrasive cloths, scourers or cleaning agents (stainless steel cleaners).
– Immediately remove laundry and cleaning agent residues.
– Do not clean the appliance with a water jet.
Clean the detergent drawer ...
... if it contains detergent or fabric softener residue.
1. Pull the drawer out until the stop position, press down the latch
on the insert and remove the drawer completely.
2. Remove insert: Pull the insert upwards using your finger.
3. Clean the detergent dispenser and the insert with water and a brush.
4. Refit the insert and secure it in place (the cylinder should fit over the
guide pin).
5. Insert the detergent drawer.
6. Leave the detergent drawer open so that residual water can evaporate.
Drum
Leave the washer dryer door open after washing so that the drum can dry.
Rust stains – use chlorine–free cleaning agent, not steel wool.
Descaling Ensure that there is no laundry in the machine!
This is not necessary if the detergent is dispensed correctly. However, if it is necessary, follow
the instructions provided by the descaler manufacturer. Suitable descaling products can be
purchased from our website or after-sales service.
After-sales service
If you cannot rectify the fault yourself Operating instructions, page 12, 13: What to do if...,
please contact our after-sales service. We will always find a suitable solution and will avoid a
visit from a service technician wherever possible.
The contact details for all countries can be found in the after-sales service directory enclosed.
Please give the after-sales service the product number (E-Nr.) and the production number
(FD) of the appliance.
You will find this information:
on the inside of the washer dryer door*/opened
service flap* and rear of the appliance.
*depending on the model
Product number Production number
Rely on the professionalism of the manufacturer. Please contact us.
This will ensure that the repair is carried out by trained service technicians who arrive
equipped with genuine spare parts for your appliance.
7
– Risk of scalding.
Allow detergent solution to cool down.
Maintenance
– Turn off the tap.
Draining the pump
Set the programme selector to Off, disconnect the mains plug.
1. Open and remove the service flap.
2. Release the drainage hose from the clip.
Remove the sealing plug from the drainage hose and allow the detergent
solution to flow out. Push the sealing cap back in.
3. Remove the pump cap. Remove foreign objects/loose debris/fluff
from inside and clean the pump. (The impeller in the pump must be
able to rotate).
4. Clean any residual lye or fluff from the thread of the pump cap
and pump housing.
5. Attach the pump cap and screw it on tight until the stop; the handle
should be pointing upwards. Place the drainage hose back in the
retainer.
6. Place the service flap back on and close.
To prevent unused detergent from flowing straight into the drain during
the next wash cycle: pour 1 litre of water into compartment II and start
the Spin programme. Then select and start a new washing programme
with detergent as usual.
Filter in the water inlet hose
Risk of electric shock
Do not immerse the Aqua-Stop safety device in water (it contains an electric valve).
Reduce the water pressure in the supply hose:
1. Turn off the tap.
2. Select any programme (except Spin or Empty(Drain)).
3. Touch Start button and allow the programme to run for approx. 40 seconds.
4. Set the programme selector to Off . Disconnect the mains plug.
Clean the filter:
1. Depending on model: Remove the supply hose from the tap.
Clean the filter with a small brush.
and/or on standard and Aqua-Secure models:
Remove the hose from the rear, remove the filter
using pliers and clean the filter.
2. Reconnect the supply hose and check
that it is tight.
8
Aqua-Stop warranty
for appliances with Aqua-Stop only
In addition to warranty claims against the seller based on the contract of sale and in addition
to our appliance warranty, we shall pay damages under the following conditions:
1. If water damage was caused by a fault in our Aqua-Stop system, we shall compensate private
users for damage.
2. The liability warranty applies to the service life of the appliance.
3. A claim can only be made under the warranty if the appliance and Aqua-Stop have been
correctly installed and connected according to our instructions; this also includes a correctly
installed Aqua-Stop extension (genuine accessory).
Our warranty does not extend to defective supply lines or fittings up to the Aqua-Stop
connection on the tap.
4. Appliances which feature Aqua-Stop can be left unattended during operation and it is not
necessary to turn off the tap afterwards.
The tap should only be turned off if you are away for a prolonged period, e.g. several weeks
holiday.
9
Washer dryer en
Installation and
maintenance instructions
Contents
Page
Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Environmentally-friendly disposal. . . . . . . . . . . . . . . . . . 1
Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Installation area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Hose and cable lengths . . . . . . . . . . . . . . . . . . . . . . . . 2
Built-under/built-in appliances . . . . . . . . . . . . . . . . . . . . 2
Removing the transport bolts . . . . . . . . . . . . . . . . . . . . 3
Water connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Transportation, e.g. if moving house . . . . . . . . . . . . . . . 6
Technical specifications. . . . . . . . . . . . . . . . . . . . . . . . . 6
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
After-sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Aqua-Stop warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Read these instructions before switching on the washer dryer.
Also follow the separate Operating instructions.
Retain all documents for subsequent use or for the next owner.