ECS H97I-DRONE User Manual
ECS H97I-DRONE User Manual

ECS H97I-DRONE User Manual

Ecs h97i-drone motherboard
Table of Contents

Advertisement

Quick Links

Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The
manufacturer makes no representations or warranties with respect to the contents
hereof and specifically disclaims any implied warranties of merchantability or
fitness for any particular purpose. The manufacturer reserves the right to revise this
publication and to make changes from time to time in the content hereof without
obligation of the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective owners
and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits
governing this device. Changes or modifications not expressly approved by the
system's manufacturer could void the user's authority to operate the equipment.
H97I-DRONE USER MANUAL
Preface
i

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H97I-DRONE and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for ECS H97I-DRONE

  • Page 1 Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to ensure compliance with the pertinent RF emission limits governing this device. Changes or modifications not expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment. H97I-DRONE USER MANUAL...
  • Page 2: Declaration Of Conformity

    Canadian Department of Communications This class B digital apparatus meets all requirements of the Canadian Interference- causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur le matériel brouilieur du Canada. H97I-DRONE USER MANUAL...
  • Page 3: About The Manual

    67 software. Using the Motherboard Software ® Describes Intel Rapid page 71 Chapter 5 ® Storage Technology RAID Intel Rapid Storage Technology Configuration. RAID Configuration Chapter 6 page 77 Provides basic trouble Trouble Shooting shooting tips. H97I-DRONE USER MANUAL...
  • Page 4 Memo H97I-DRONE USER MANUAL...
  • Page 5: Table Of Contents

    The Standard Configuration...........29 Entering the Setup Utility............29 Resetting the Default CMOS Values........30 Using BIOS..................31 BIOS Navigation Keys..............31 Main Menu................32 Advanced Menu..............33 Chipset Menu................46 M.I.B.X (MB Intelligent BIOS X) Menu........54 Security Menu.................63 Boot Menu................64 Exit Menu................65 Updating the BIOS..............66 H97I-DRONE USER MANUAL...
  • Page 6 ® Creating a RAID set.................73 Deleting a RAID set................75 Resetting disks to Non-RAID.............76 Exiting Setup................76 Chapter 6 Trouble Shooting Start up problems during assembly..........77 Start up problems after prolong use..........78 Maintenance and care tips..............78 Basic Troubleshooting Flowchart...........79 H97I-DRONE USER MANUAL...
  • Page 7: Introducing The Motherboard

    Chapter 1 Introducing the Motherboard Introduction Thank you for choosing the H97I-DRONE motherboard. This motherboard is a high performance, enhanced function motherboard designed to support the LGA1150 ® socket for 4 and 5 Generation Intel Core processors. ® ® ® ® ®...
  • Page 8: Specifications

    • LGA1150 socket for 4 and 5 Generation Intel Core processors • Supports max CPU TDP 100W Note: Please go to ECS website for the latest CPU support list. ® Chipset • Intel H97 Chipset Memory • Dual-channel DDR3 memory architecture •...
  • Page 9 Support Anti Virus* /Muzee* /Sound Blaster Cinema2* /MAGIX* Note: Microsoft .NET Framework 3.5 is required. Free bundle software including ECS DVD: Cyberlink Media Suite/Norton Anti Virus/Muzee/Sound Blaster Cinema2/MAGIX Form Factor • Mini ITX Size, 170mm x 170mm H97I-DRONE USER MANUAL...
  • Page 10: Motherboard Components

    Motherboard Components H97I-DRONE USER MANUAL...
  • Page 11 Serial ATA 6Gb/s connectors 15. BZ Buzzer 16. F_PANEL Front panel switch/ LED header 17. F_USB Front panel USB 2.0 header 18. CASE CASE open header 19. CLR_CMOS Clear CMOS jumper 20. USB3F Front panel USB3.0 header H97I-DRONE USER MANUAL...
  • Page 12: I/O Ports

    E: Mic_in Rear C: Line-in —— The above port definition can be changed to audio input or audio output by changing the driver utility setting. 8. Optical SPDIF Output This jack connects to external optical digital audio output devices. H97I-DRONE USER MANUAL...
  • Page 13: Installing The Motherboard

    Do not over-tighten the screws as this can stress the motherboard. When installing 24-pin ATX power cable, please note the overhead space because of the chassis design of the Motherboard, avoiding to damage the motherboard with excessive power. H97I-DRONE USER MANUAL...
  • Page 14: Checking Jumper Settings

    The following illustration shows the location of the motherboard jumpers. Pin 1 is labeled. To avoid the system instability after clearing CMOS, we recommend users to enter the main BIOS setting page to “Load Default Settings” and then “Save and Exit Setup”. H97I-DRONE USER MANUAL...
  • Page 15: Installing Hardware

    Lift the tail of the load lever and rotate the load plate to fully open position. Grasp the edge of the package substrate. Make sure pin 1 indicator is on your bottom-left side. Aim at the socket and place the package carefully into the socket by purely vertical motion. H97I-DRONE USER MANUAL...
  • Page 16 Spreader). Engage the load lever while pressing down lightly onto the load plate. Secure the load lever with the hook under retention tab. Then the cover will flick automatically. Please save and replace the cover onto the CPU socket if processor is removed. H97I-DRONE USER MANUAL...
  • Page 17: Installing The Cpu Cooler

    B. Fasten the cooling fan supporting base onto the CPU socket on the motherboard. And make sure the CPU fan is plugged to the CPU fan connector. C. Connect the CPU cooler power connector to the CPU_FAN connector. H97I-DRONE USER MANUAL...
  • Page 18: Installing Memory Modules

    Install the DIMM module into the slot and press it firmly down until it seats correctly. Check that the cutouts on the DIMM module edge connector match the notches in the DIMM slot. The slot latches are levered upwards and latch on to the edges of the DIMM. H97I-DRONE USER MANUAL...
  • Page 19 Due to Intel CPU spec definition, please follow the table above for recommended memory configuration. We suggest users not to mix memory type. It is recommended to use the same brand and type memory on this motherboard. H97I-DRONE USER MANUAL...
  • Page 20: Installing Add-On Cards

    Mini PCIe interface. Before installing an add-on card, check the documentation for the card carefully. If the card is not Plug and Play, you may have to manually configure the card before installation. H97I-DRONE USER MANUAL...
  • Page 21 Please refer the following steps to install the M.2 Wifi/ Bluetooth card: Demount the screw not used according to the length of your M.2 Wifi/ Bluetooth card Insert the M.2 Wifi/ Bluetooth card into M.2 slot in the fool-proof way. H97I-DRONE USER MANUAL...
  • Page 22 Lock the screw as the following picture shows to make sure the M.2 Wifi/ Bluetooth card is installed in place. H97I-DRONE USER MANUAL...
  • Page 23: Connecting Optional Devices

    2-4-5. Connecting Optional Devices Refer to the following for information on connecting the motherboard’s optional devices: Components Components F_USB F_AUDIO CASE SATA3_1~5 USB3F H97I-DRONE USER MANUAL...
  • Page 24 The front panel audio header allows the user to install auxiliary front-oriented mi- crophone and line-out ports for easier access. This header supports HD audio by default. If you want connect an AC’ 97 front panel audio to HD onboard headers, please set as below picture. H97I-DRONE USER MANUAL...
  • Page 25 If you use AC’ 97 Front Panel, please don’ t tick off “Using Front Jack Detect ”. If you use HD Audio Front Panel, please tick off the option of “Using Front Jack Detect ”. * For reference only H97I-DRONE USER MANUAL...
  • Page 26 USB connector to connect the front-mounted ports to the motherboard. Please make sure that the USB cable has the same pin assignment as indi- cated above. A different pin assignment may cause damage or system hang- H97I-DRONE USER MANUAL...
  • Page 27 This Motherboard implements one USB 3.0 header supporting 2 extra front USB 3.0 ports, which delivers 5Gb/s transfer rate. Please make sure that the USB cable has the same pin assignment as indi- cated above. A different pin assignment may cause damage or system hang- H97I-DRONE USER MANUAL...
  • Page 28: Installing A Sata Hard Drive

    Attach either cable end to the connector on the motherboard. Attach the other cable end to the SATA hard drive. Attach the SATA power cable to the SATA hard drive and connect the other end to the power supply. * For reference only H97I-DRONE USER MANUAL...
  • Page 29: Connecting Case Components

    2-4-7. Connecting Case Components After you have installed the motherboard into a case, you can begin connecting the motherboard components. Refer to the following: Components Components ATX_POWER SYS_FAN ATX12V CPU_FAN F_PANEL H97I-DRONE USER MANUAL...
  • Page 30 The ATX 24-pin connector allows you to connect to ATX v2.x power supply. With ATX v2.x power supply, users please note that when installing 24-pin power cable, the latches of power cable and the ATX match perfectly. 24-pin power cable H97I-DRONE USER MANUAL...
  • Page 31 Connectors) Connect the CPU cooling fan cable to CPU_FAN. Connect the system cooling fan connector to SYS_FAN. Users please note that the fan connector supports the CPU cooling fan of 1.1A ~ 2.2A (26.4W max) at +12V. H97I-DRONE USER MANUAL...
  • Page 32 5. BZ: Buzzer header Connect the case speaker cable to SPK. H97I-DRONE USER MANUAL...
  • Page 33: Front Panel Header

    50 ms to signal the power supply to switch on or off. The time requirement is due to internal de-bounce circuitry. After receiving a power on/off signal, at least two seconds elapses before the power supply recognizes another on/off signal. This concludes Chapter 2. The next chapter covers the BIOS. H97I-DRONE USER MANUAL...
  • Page 34 Memo H97I-DRONE USER MANUAL...
  • Page 35: Using Bios

    When you power on the system, BIOS enters the Power-On Self Test (POST) routines. POST is a series of built-in diagnostics performed by the BIOS. After the POST routines are completed, the following message appears: Press DEL to enter SETUP H97I-DRONE USER MANUAL...
  • Page 36: Resetting The Default Cmos Values

    Wrong” message. This standard message will appear following a clear CMOS data at factory by the manufacturer. You simply need to Load Default Settings to reset the default CMOS values. Note: Changes to system hardware such as different CPU, memories, etc. may also trigger this message. H97I-DRONE USER MANUAL...
  • Page 37: Using Bios

    BIOS setup screens shown in this chapter are for reference only and may differ from the actual BIOS. Please visit the manufacture’s website for updated manual. 2. In this Gui BIOS, you can operate by mouse or keyboard. Click : select item; Double click: enter; Right click: exit. H97I-DRONE USER MANUAL...
  • Page 38: Main Menu

    The Date and Time items show the current date and time on the computer. If you are running a Windows OS, these items are automatically updated whenever you make changes to the Windows Date and Time Properties utility. H97I-DRONE USER MANUAL...
  • Page 39: Advanced Menu

    Intel(R) Rapid Start Technology Enter/Dbl Click : Select Intel ME BIOS Extension Configuration +/- : Change Opt. Intel(R) Ethernet Connection (2) I218-V - 88:88:88:88:87:88 F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit H97I-DRONE USER MANUAL...
  • Page 40: Lan Configuration

    F2: Previous Values F3: Optimized Defaults F4: Save & Exit F9: Capture Screen ESC/Right Click: Exit Onboard LAN Controller (Enabled) Use this item to enable or disable Onboard LAN controller. Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 41: Pc Health Status

    Smart Fan Slope PWM value Fan Full Speed Offset (DTS) : Select Screen /Click: Select Item Enter/Dbl Click : Select +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit H97I-DRONE USER MANUAL...
  • Page 42 Core Voltage • DIMM Voltage • +12V • • +3.3V Press <Esc> to return to the Advanced Menu page. TCC Activation Temperature (DTS) (100) This item is used to set the value from the factory TCC activation temperature. H97I-DRONE USER MANUAL...
  • Page 43: Power Management Setup

    EUP Function (Enabled) This item allows user to enable or disable EUP support. Power LED Type (Dual Color LED) This item shows the type of the Power LED. Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 44: Acpi Settings

    F4: Save & Exit ESC/Right Click: Exit ACPI Sleep State [S3(Suspend to RAM)] This item allows user to enter the ACPI S3 (Suspend to RAM) Sleep State (default). Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 45: Cpu Configuration

    Use this item to control the number of active processor cores. Limit CPUID Maximum (Disabled) Use this item to enable or disable the maximum CPUID value limit, you can enables this item to prevent the system from “rebooting” when trying to install Windows NT 4.0. H97I-DRONE USER MANUAL...
  • Page 46 Use this item to set the package C state limit. Enhanced Halt (C1E) (Enabled) Use this item to enable the CPU energy-saving function when the system is not running. Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 47: Sata Configuration

    Spin Up Device (Disabled) Use this item to enable or disable the spin up device. External SATA (Disabled) Use this item to enable or disable the external SATA. Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 48: Usb Configuration

    All USB Devices (Enabled) Use this item to enable or disable all USB devices. Legacy USB Support (Enabled) Use this item to enable or disable support for legacy USB devices. Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 49: Intel Rapid Start Technology

    F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit Intel(R) Rapid Start Technology (Disabled) Use this item to enable or disable the Intel(R) Rapid Start Technology. Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 50 This item allows you to enable or disable the BIOS Hotkey Pressed. MEBx Selection Screen (Disabled) This item allows you to enable or disable the MEBx Selection Screen. Press <Esc> to return to the Advanced Menu page. H97I-DRONE USER MANUAL...
  • Page 51 This item allows you to enable or disable serial port. Wake On LAN (Enabled) This item allows you to enable or disable Wake on LAN function. Press <Esc> to return to the Intel(R) Ethernet Connection I218-V page. H97I-DRONE USER MANUAL...
  • Page 52: Chipset Menu

    This item shows the information of the IGD (Internal Graphics Device) memory. DVMT Memory (256M) When set to Fixed Mode, the graphics driver will reserve a fixed position of the system memory as graphics memory, according to system and graphics requirements. H97I-DRONE USER MANUAL...
  • Page 53 This item allows you to enable or disable the IGD Multi-Monitor. CPU SA Audio Device (Enabled) This item allows you to enable or disable the CPU SA Audio device. Press <Esc> to return to the Chipset Menu page. H97I-DRONE USER MANUAL...
  • Page 54 Intel integrated Graphics and one or two PCI-Express graphics devices under Windows 7/8/8.1. Step 1. Insert ECS drives DVD to run Auto setup or browse the DVD to install Intel chipset drivers, VGA and sound drivers.(If you want know the detail information, please refer to chapter 4.)
  • Page 55 : Select Screen IGD Multi-Monitor Disabled /Click: Select Item Enter/Dbl Click : Select CPU SA Audio Device Enabled +/- : Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit H97I-DRONE USER MANUAL...
  • Page 56 Extend desktop to this display You must select Apply before making additional changes. Disconnect this display Make this my main display Advance settings Make text and other items larger or smaller What display settings should I choose? Cancel Apply H97I-DRONE USER MANUAL...
  • Page 57 Multiple displays: Extend desktop to this display You must select Apply before making additional changes. Make this my main display Advance settings Make text and other items larger or smaller What display settings should I choose? Cancel Apply H97I-DRONE USER MANUAL...
  • Page 58: Pch Configuration

    This item enables or disables the warning if the case is opened up, and the item below indicates the current status of the case. Chassis Opened (No) This item indicates whether the case has been opened. Press <Esc> to return to the Chipset Menu page. H97I-DRONE USER MANUAL...
  • Page 59 F4: Save & Exit ESC/Right Click: Exit ME Control (Enabled) Use this item to enable or disable the ME Firmware. ME FW Version (9.1.2.1010) This item shows the ME FW version. Press <Esc> to return to the Chipset Menu page. H97I-DRONE USER MANUAL...
  • Page 60: Mb Intelligent Bios X) Menu

    PEG/ DMI Ratio LCPLL or SBPLL select LCPLL CPU Ratio (28) This item allows you to control non turbo CPU ratio. Package Current Lock (Disabled) This item allows you to enable or disable the package current lock. H97I-DRONE USER MANUAL...
  • Page 61 PEG/DMI Ratio (1.00) This item shows the information of the PEG/DMI Ratio. LCPLL or SBPLL select (LCPLL) This item allows you to select the ICC clocking mode. Press <Esc> to return to the M.I.B. X Menu page. H97I-DRONE USER MANUAL...
  • Page 62: Memory Configuration

    Memory Frequency (1333 MHz) This item shows the information of the memory frequency. Total Memory (4096 MB (DDR3)) This item shows the information of the total memory. Press <Esc> to return to the M.I.B. X Menu page. H97I-DRONE USER MANUAL...
  • Page 63 This item allows you to enable or disable the CMD Tri-State (ending of the training). Memory Scrambler (Enabled) This item allows you to enable or disable the memory scrambler. MRC Fast Boot (Enabled) This item allows you to enable or disable the MRC fast boot. H97I-DRONE USER MANUAL...
  • Page 64: North Bridge Configuration

    F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit Graphics Core Ratio Limit (22) This item allows you to control the internal GFX core ratio. Press <Esc> to return to the M.I.B. X Menu page. H97I-DRONE USER MANUAL...
  • Page 65 DIMM Voltage 1.536 V (Auto) This item allows you to adjust the DIMM voltage. Processor Input Voltage (Auto) This item allows you to adjust the processor input voltage. Vdroop (Enabled) Use this item to enable or disable the Vdroop. H97I-DRONE USER MANUAL...
  • Page 66 If this function is dis- abled, it will not be changed until CPU powers down. RING Ratio (32) This item allows you to set the RING Ratio. Press <Esc> to return to the M.I.B. X Menu page. H97I-DRONE USER MANUAL...
  • Page 67 F3: Optimized Defaults F4: Save & Exit ESC/Right Click: Exit Restore last setting (Disabled) This item allows you to enable or disable to restore the last setting. Press <Esc> to return to the M.I.B. X Menu page. H97I-DRONE USER MANUAL...
  • Page 68 This is display-only field and displays the information of the CPU installed in your computer. Processor Speed (3200 MHz) This item shows the CPU speed. Memory Frequency (1333 MHz) This item shows the memory frequency. Total Memory (4096 MB (DDR3)) This item shows the total memory. F1: General Help H97I-DRONE USER MANUAL...
  • Page 69: Security Menu

    Secure Boot state (Not Active) This item allows you to enable or disable the secure boot state. Secure Boot (Disabled) This item is used to control the secure boot flow, it is possible only if system runs in User Mode. H97I-DRONE USER MANUAL...
  • Page 70: Boot Menu

    Boot Option #1 /2 /3 /4 /5 /6 /7 These items show the boot priorities. USB/Floppy Drive Priorities This item enables you to specify the sequence of loading the operating system. Press <Enter> to see the submenu. H97I-DRONE USER MANUAL...
  • Page 71: Exit Menu

    Discard Changes This item enables you to discard any changes that you have made. Restore Defaults This item enables you to restore defaults to all the setup options. Boot Override Use this item to select the boot device. H97I-DRONE USER MANUAL...
  • Page 72: Updating The Bios

    BIOS jumper, reset the jumper to protect the newly installed BIOS from being overwritten. The computer will restart automatically. This concludes Chapter 3. Refer to the next chapter for information on the software supplied with the motherboard. H97I-DRONE USER MANUAL...
  • Page 73: Using The Motherboard Software

    Click Setup. The installation program begins: The following screens are examples only. The screens and driver lists will be different according to the motherboard you are installing. The motherboard identification is located in the upper left-hand corner. H97I-DRONE USER MANUAL...
  • Page 74 Windows 8 will show the following screen after system restart, you must select “Desktop” in the bottom left to install the next driver. H97I-DRONE USER MANUAL...
  • Page 75: Manual Installation

    (README.TXT or README.DOC) for information on installing the driver or software for your operating system. These software(s) are subject to change at anytime without prior notice. Please refer to the support disk for available software. H97I-DRONE USER MANUAL...
  • Page 76 Just select the one you prefer and start to download and install the drivers. eBLU ECS eBLU utility makes BIOS update faster and easier. eBLU will list the latest BIOS with a default check-mark. Click”install” button to install. Microsoft .NET Framework 3.5 is required.
  • Page 77: Intel Rapid Storage Technology Raid Configuration

    F2: Previous Values F3: Optimized Defaults External SATA Disabled F4: Save & Exit ESC/Right Click: Exit SATA Port4 Not Present Spin Up Device Disabled External SATA Disabled SATA Port5 Not Present Spin Up Device Disabled External SATA Disabled H97I-DRONE USER MANUAL...
  • Page 78: Entering Intel ® Rapid Storage Technology Raid Bios Utility

    6. Exit DISK/VOLUME INFORMATION RAID Volumes: None defined. Physical Devices: ID Device Model Serial # Size Type/Status (Vol ID) 2 WDC WD2001FASS-0 WD-WMAUR0083571 1.8TB Non-RAID Disk 3 SAMSUNG HD203WI S1UYJ1BZ203313 1.8TB Non-RAID Disk [ ]-Select [ESC]-Exit [ENTER]-Select Menu H97I-DRONE USER MANUAL...
  • Page 79: Creating A Raid Set

    Capacity. The default value indicates the maximum capacity using the selected disks. Entering a lower capacity allows you to create a second volume on these disks. [ CREATE VOLUME MENU ] Name: Volume0 RAID Level: RAID0(Stripe) Disks: Select Disks Strip Size: 128KB Capacity: 931.5 Create Volume H97I-DRONE USER MANUAL...
  • Page 80 RAID 1 (Mirror) is set to provide the data backup. If you want to set RAID 0, you need to set the 2nd Boot Device item in the BIOS to Intel Volume0. See section “Advanced Setup” for details. H97I-DRONE USER MANUAL...
  • Page 81: Deleting A Raid Set

    Are you sure you want to delete “Volume0”? (Y/N): Deleting a volume will reset the disks to non-RAID. WARNING: ALL DISK DATA WILL BE DELETED. [ ]Select [ESC]-Previous Menu [DEL]-Delete Volume Pressing <Y> deletes all the data in the HDDs. H97I-DRONE USER MANUAL...
  • Page 82: Resetting Disks To Non-Raid

    <Enter> to exit the Intel Rapid Storage Technology RAID BIOS utility. A dialogue box appears to confirm the action. Press <Y> to confirm; otherwise, press ® <N> to return to the Intel Rapid Storage Technology RAID BIOS menu. H97I-DRONE USER MANUAL...
  • Page 83: Trouble Shooting

    Before calling for technical support or returning for warranty, this chapter may help to address some of the common questions using some basic troubleshooting tips. You may also log onto our ECS website for more information: http:// www.ecs.com.tw/ECSWebSite/Support/Support_FAQ.aspx?MenulD=49& childid=M 49&LanlD=0 a) System does not power up and the fans are not running.
  • Page 84: Start Up Problems After Prolong Use

    5. Check whether there is any bulked up electrolytic capacitor or abnormal component. Please log onto our ECS website: http://www.ecs.com.tw/ECSWebSite/Support/ Technical_Support_List.aspx?MenuID=50&LanID=0 for more information. Maintenance and care tips Your computer, like any electrical appliance, requires proper care and maintenance.
  • Page 86 Memo H97I-DRONE USER MANUAL...

Table of Contents