Sanyo DC-F21 Instruction Manual page 12

ING TO TH~ ,,.
—...—,'.>.
To turn the unit on and listen to the last received station, press the
TUNER/BAND button.
Automatic/Manual tuning
1. Press the TUNER/BAND button to select the desired band.
"TUNER" is selected automatically, "TUNE" appears on the
display, then "TUNE" is replaced by the tuner mode display.
For UK: FM — MW — LW
For AU: FM — AM
2. Automatic tuning
Press the + or – TUNING button (more than 0.7 seconds) to tune in
a station. The unit will scan up or down the band and receive the next
receivable station. Press the button again to continue.
Manual tuning
Press the + or – TUNING button briefly (less than 0.7 seconds) until
the desired frequency is displayed. Each time the button is pressed,
the frequency changes in 0.05 MHzstepsfor FM, 9 kHzstepsfor MW/
AM and LW.
In Iw I l—l :1 —1 1:
I II
I l_l _l ~ _i
MHz
To preset stations
For UK: Up to 24 stations for FM band, 12 stations for MW band, and up
to 4 stations for LW band can be preset.
For AU: Up to 24 stations for FM band, and up to 12 stations for AM band
can be preset.
Automatic presetting (APT)
1. Press the TUNER/BAND button to select the desired band.
2. Press and hold down the MEMORY button for at least 3 seconds.
"PROG. " blinks.
The automatic tuning mode is set and automatic presetting begins
from the low end of the band.
When 24 stations (12 stations for MW/AM or 4 stations for LW) have
been preset or the high end of the band is reached, automatic
presetting stops. "PROG." disappears and the station memorized on
channel number 1 will be heard.
3. To preset stations on the other band, follow steps above.
Note:
If APT is activated, all previously programmed stations of the band will be
cleared and new stations will be programmed.
Manual presetting
1. Tune in the station to be preset as described in "Automatic/Manual
tuning",
2. Press the MEMORY button.
PROG
/l\
— —
I l—l :1 :1 1:
i l_l _l l_ _l
MH,
3, Press the+ or – PRESET button to select the channel number to be
preset.
PROG
/l\
4.
5.
Press the MEMORY button.
Inthisexample, "103.25 MHz" FM station is preset on FMchannel
number 9.
The number buttons on the remote control can be used to select
the preset station. In this example, press O, then 9 after the step
2 above.
1: Iw I l—l :1 :1 1:
II I l_l _l I_ _l
MHz
Note:
If the next step is not taken within 10 seconds while performing steps
2-4, "PROG." disappears and the preset operation is cancelled.
Press the MEMORY button to continue.
Repeat the steps above to add more preset stations.
When presetting a new station, the previously preset station on the
same channel number of the same band is cleared.
The preset stations will be retained in the memoty even if the unit is
turned off.
If the memory contents are lost due to a power failure or other
condition, preset the stations again.
Listening to preset stations
1, Press the TUNER/BAND button to select the desired band.
2. Press the + or– PRESET button (less than 0.7 seconds) to select the
desired channel number.
The number buttons on the remote control can also be used.
Press two number buttons within 4 seconds.
Preset scan tuning
1.
2.
3.
Press the TUNER/BAND button to select the desired band.
Press the + PRESET button (more than 0.7 seconds). The channel
number blinks on the display. Each of the preset stations is tuned in
for 5 seconds.
When the desired station has been tuned in, press the + PRESET
button again to keep the reception locked at that station.
To receive an FM stereo broadcast, make sure that "MONO is not
displayed. If "MONO appears, press the FM MODE button to turn the
"MONO indication off,
"ST appears when an FM stereo broadcast is received.
If the sianal from an FM stereo station is weak and reception is poor,
press tie FM MODE button to change to monaural reception. ("ST" is
replaced by "MONO in the display.)
Changing the MWIAM reception frequencies
It is not necessary to perform this procedure in the Europe (or in the
Australia and New Zealand).
1. Press the TUNER/BAND button to select 'rMW or "AM".
2. While pressing the MEMORY button on the front panel, press the
button (CD section) on the front panel.
For UK:
522-1611
kHz (9 kHz steps) — 520-1610 kHz (10 kHzsteps)
For AU:
522-1710
kHz (9 kHz steps) — 520-1710 kHz (10 kHz steps)
LISTENING TO VIDEO, SOURCES
1. Select "VIDEO function. "VIDEO appears on the display.
2. Follow the instructions supplied with the video equipment.
11