Epson SC-F2000 Series User Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Printer
  5. SC-F2000 Series
  6. User manual

Epson SC-F2000 Series User Manual

Hide thumbs Also See for SC-F2000 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: User Manual, Setup Manual
User's Guide
CMP0006-00 EN

Advertisement

Table of Contents
loading

Related Manuals for Epson SC-F2000 Series

Summary of Contents for Epson SC-F2000 Series

  • Page 1 User’s Guide CMP0006-00 EN...

  • Page 2: Copyrights And Trademarks

    (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions. Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson Corporation.

  • Page 3: Table Of Contents

    Disposing of Used Consumables and Optional Using EPSON LFP Remote Panel 2..22 Parts....... . . 51 Removing the Software.
  • Page 4 Technical Support Web Site....87 Contacting Epson Support....87 Before Contacting Epson.

  • Page 5: Introduction

    SC-F2000 Series User’s Guide Introduction ❏ Keep the entire computer system away from Introduction potential sources of electromagnetic interference, such as loudspeakers or the base units of cordless telephones. ❏ Use only the type of power source indicated on the Important Safety product’s label.

  • Page 6: When Handling The Ink Cartridges

    SC-F2000 Series User’s Guide Introduction ❏ Do not move the print heads by hand; otherwise Notes contain useful or Note you may damage this product. additional information on the operation of this product. ❏ Always turn the product off using the Power button on the control panel.

  • Page 7: Printer Parts

    SC-F2000 Series User’s Guide Introduction Printer Parts Front section Printer cover Open when cleaning the inside of the printer. Airflow vents Lets out air from the printer. Do not block the airflow vents. Cartridge cover (left) Open when replacing or shaking ink cartridges.
  • Page 8 SC-F2000 Series User’s Guide Introduction Fixing lever Fixes the height adjustment lever in place. You can adjust the angle of the lever. “Adjusting the angle of the fixing lever” on page 37 Cartridge cover (right) Open when replacing or shaking ink cartridges.

  • Page 9: Interior

    Air filter The air from the printer passes through this filter during operation. If a message on the control panel prompts you to replace the air filter, contact your dealer or Epson Support. Print head Fires ink while moving left and right to print.
  • Page 10 SC-F2000 Series User’s Guide Introduction Suction cap Sucks out the ink during head cleaning to unclog the nozzles. Wiper unit Wipes the ink from the print head nozzles. The wiper unit is a consumable product. Replace it if a message is displayed.

  • Page 11: Rear Section

    SC-F2000 Series User’s Guide Introduction Rear section AC inlet Connect the supplied power cable here. Waste ink outlet (Left) An outlet for the waste ink tube. Waste ink is ejected from here. Tube clamp A clamp that fixes the waste ink tube to the printer. See the Setup Guide for details on attaching and removing the clamp.
  • Page 12 SC-F2000 Series User’s Guide Introduction Data light Indicates the network connection status and data reception by lighting or flashing. Connected. Flashing Receiving data. Status light Indicates the network transmission speed by the color of the light. Green 10Base-T 100Base-T USB port Connect the USB cable here.

  • Page 13: Control Panel

    SC-F2000 Series User’s Guide Introduction Control panel Plight (Power light) Indicates the printer's operational status by lighting or flashing. The power is on. Flashing The printer is operating such as receiving data, shutting down, or moving the movable base. The power is off.
  • Page 14 SC-F2000 Series User’s Guide Introduction l button If you press this button while the menu is displayed, you move back a step in the following order: setting value -> setting item -> menu. “Menu Operations” on page 64 u/d buttons (Up/Down buttons) When menus are displayed, these buttons can be used to select a setting item or a setting value.

  • Page 15: Screen View

    SC-F2000 Series User’s Guide Introduction 1 Status indicators Screen View The waste ink bottle status is indicated as follows. : The height of the indicator corresponds to the remaining capacity. : The waste ink bottle is almost full. Prepare a new waste ink bottle.

  • Page 16: Features

    Automatic wiper system A built-in automatic wiper system has been newly developed for Epson pigment ink textile printers. Stable print quality has been achieved by automatically cleaning the surface of the print head nozzles.

  • Page 17: Ease-Of-Use

    Notes on Usage and High density white printing has been achieved by using White ink and pre-treatment liquid developed specially Storage for Epson pigment ink textile printers. Installation space Ease-of-Use Make sure that you secure the following space, clear of...

  • Page 18: Notes For When Not Using The Printer

    SC-F2000 Series User’s Guide Introduction ❏ Do not bend or pull the waste ink tubes. Otherwise “Notes on Handling White Ink” on page 19 ink may leak inside or outside the printer. ❏ If you do not print for a long time, the print head ❏...

  • Page 19: Notes On Handling White Ink

    SC-F2000 Series User’s Guide Introduction ❏ If you remove an ink cartridge before it is empty, As well as the following, there are additional points to note when using White ink. Check the following points. wipe off any ink that is stuck on the ink supply port using the cleaning stick in the supplied maintenance kit.

  • Page 20: Notes On Handling T-Shirts (Media)

    SC-F2000 Series User’s Guide Introduction ❏ Wash the ink tubes when a message is displayed to ❏ Do not use organic solvents such as alcohol. prevent print quality declining due to ❏ Do not rub the printed surface against vinyl sedimentation in the tubes.

  • Page 21: Using The Software

    Installs the Epson communication driver (EPSON SC-F2000 Series Comm Driver). The Epson communication driver is not the printer driver. If you connect the printer to a computer using a USB cable without installing the Epson communication driver, the printer's status may not be displayed in Garment Creator or software RIP.

  • Page 22: Using Epson Lfp Remote Panel 2

    LFP Remote Panel 2 - EPSON LFP Remote Panel Turn off the printer, and unplug the interface cable. Click the item you want to use on the EPSON LFP Click Programs - Uninstall a program on the Remote Panel 2 main screen.
  • Page 23 SC-F2000 Series User’s Guide Introduction Drag and drop the EPSON Remote Panel 2 folder from the Applications folder into the Trash. Use the "Uninstaller" to remove other software applications. Delete the software first when reinstalling or upgrading. Downloading the Uninstaller Download the Uninstaller from the Epson Web site.

  • Page 24: Basic Printing

    SC-F2000 Series User’s Guide Basic Printing Basic Printing Overview This section explains the basic workflow from preparing a T-shirt before printing to post-treatment after printing. Operation Item Description Reference Page Preparation Check items required in addition to the printer. “Necessary Items” on...
  • Page 25 SC-F2000 Series User’s Guide Basic Printing Post-treatment Fixate the ink to the T-shirt. “Post-treatment” on page 39...

  • Page 26: Necessary Items

    SC-F2000 Series User’s Guide Basic Printing Pure water (commercially available) Necessary Items Pure water, such as distilled and purified water, is used to dilute the pre-treatment liquid. To print on a T-shirt using this printer, you also need the Pre-treatment liquid roller (commercially available) following devices and parts.

  • Page 27: Pre-Treatment

    “Necessary Items” on page 26 Important: Read the safety data sheet before use. You can download ❏ Liquid may be spattered about when applying the safety data sheet from the Epson Web site. the pre-treatment liquid. Always wear protective eyewear and gloves when URL: http://www.epson.com...
  • Page 28 SC-F2000 Series User’s Guide Basic Printing Disposal method Remove the cap. Pre-treatment liquid is classified as industrial waste. Dispose of pre-treatment liquid according to your local laws and statutes such as entrusting it to an industrial waste disposal company. When handing over the pre-treatment liquid to the industrial waste disposal company, make sure you include the safety data sheet.
  • Page 29 SC-F2000 Series User’s Guide Basic Printing Pouring If you do not dilute the pre-treatment liquid or make it Remove the cap from the tap, and then turn the too strong, the liquid leaves noticeable traces or the lever until the hole is facing down.

  • Page 30: Fixating The Pre-Treatment Liquid (Heat Press)

    SC-F2000 Series User’s Guide Basic Printing Squeeze the pre-treatment liquid out of the roller Place the T-shirt on a flat surface, and then spray by pressing it against the edge of the tray, and the pre-treatment liquid evenly over the print apply the liquid evenly.

  • Page 31: Preparing The Printer

    SC-F2000 Series User’s Guide Basic Printing When White ink is loaded, shake the White ink Pre-treatm Temperatu Time Pressure cartridge. ent Liquid Applicatio n Area “Replacing and Shaking Cartridges” on page 58 A4 and 170 °C 45 secs. 4.2 N/cm smaller Check for clogged nozzles.

  • Page 32: Creating And Transmitting Data

    Garment Creator is ❏ Only the following operations are possible while not stored on the software disc supplied. receiving data. It can be downloaded from the Epson website. ❏ Turning off the power http://www.epson.com ❏ Moving the movable base (platen) ❏...

  • Page 33: From Other Software Applications

    SC-F2000 Series User’s Guide Basic Printing Load the T-shirt (media) From other software applications This section explains how to load a T-shirt (media) into Apart from Adobe Photoshop and Adobe Illustrator, the printer. you cannot print directly from other software applications such as CorelDRAW.

  • Page 34: Loading On The Platen

    SC-F2000 Series User’s Guide Basic Printing Attach the platen frame again. Loading on the Platen Check that the platen is ejected forward. If it is not ejected, press the } button to move the platen forward. Remove the platen's frame.
  • Page 35 SC-F2000 Series User’s Guide Basic Printing Pull the T-shirt outside of the frame to remove Tuck in the T-shirt around the frame so that it any creases and slack. does not drape over the movable base. If the height sensor reacts while...

  • Page 36: Adjusting The Height

    SC-F2000 Series User’s Guide Basic Printing To adjust the height again, move the height Adjusting the Height adjustment lever to change the recommended position. The optimum height of the platen is one step lower than the position where Platen Height Error is displayed on the control panel.
  • Page 37 SC-F2000 Series User’s Guide Basic Printing Press the } button to move the platen into the Pull the fixing lever to the right, and then adjust it printer. to an easy to use position. Check that Platen Height Error is displayed on the control panel.

  • Page 38: Starting And Canceling Printing

    SC-F2000 Series User’s Guide Basic Printing Press the u/d buttons to highlight Yes, and then Starting and Canceling press the Z button. Printing Printing stops immediately when the button is pressed, and data is deleted. Starting When the printer has finished receiving data, the x light turns on.

  • Page 39: Post-Treatment

    SC-F2000 Series User’s Guide Basic Printing Fixation conditions differ between the heat press and Post-treatment the oven. As the optimum conditions vary depending on the type of heat press or oven being used and the amount of ink, the following values are only a guide. If...
  • Page 40 SC-F2000 Series User’s Guide Basic Printing Type of Oven Temperature Time Conveyor type 160 °C* 3.5 to 4.5 minutes * Temperature of the fixating surface of the T-shirt. Not the internal temperature. If the surface of the T-shirt exceeds 180 °C, the T-shirt and the print surface may change color.

  • Page 41: Other Printing Methods

    SC-F2000 Series User’s Guide Other Printing Methods Save the data in the root folder on the USB memory. If Other Printing the data is saved in a sub-folder, it is not displayed even if the USB memory stick is connected to the printer.

  • Page 42: Printing On Thick Material (Media)

    SC-F2000 Series User’s Guide Other Printing Methods Confirm that USB File List is highlighted, and Printing on Thick Material then press the r button. (Media) Confirm that Select Print File is highlighted, and then press the r button. You can lower the height of the printing surface by 10...
  • Page 43 SC-F2000 Series User’s Guide Other Printing Methods Loosen the fixing lever. Remove the three screws inside the height adjustment lever. Keep the removed screws in a safe place. Remove the screw that secures the parallel adjustment plate. Keep the removed screws in a safe place.

  • Page 44: Installing The Labeled Round Part

    SC-F2000 Series User’s Guide Other Printing Methods Tighten the fixing lever, and then secure the height adjustment lever. Attach the height adjustment lever. Do not attach the screw removed in step 7. Attach the platen. Attach the parallel adjustment plate.

  • Page 45: Maintenance

    SC-F2000 Series User’s Guide Maintenance Loading paper Maintenance This section explains how to load paper to print a nozzle check pattern. Prepare the following A4 or letter size media depending on the mode being used. Adjusting the Print Head White ink mode: Transparent media such as an OHP...

  • Page 46: Control Panel Operations

    SC-F2000 Series User’s Guide Maintenance Secure the paper with cellophane tape and so on Check that paper is loaded on the platen. to keep it in place. “Loading paper” on page 45 Press the - button. The Maintenance menu is displayed.

  • Page 47: Correcting The Print Misalignment

    SC-F2000 Series User’s Guide Maintenance Head cleaning levels Press the u/d buttons to highlight the method You can select from three levels of head cleaning. Use for cleaning the nozzle row, and then press the r light or medium for normal cleaning. Use heavy button.

  • Page 48: Head Alignment

    SC-F2000 Series User’s Guide Maintenance ❏ Head Alignment (when there are vertical lines or Check that T-shirt is loaded, and then press the faint text) Z button again. ❏ Offset Head Alignment (when you want to fine tune The check pattern is printed.

  • Page 49: Periodic Maintenance

    SC-F2000 Series User’s Guide Maintenance Periodic Maintenance Suction cap When a message is displayed “Cleaning Caps” on page 51 To maintain optimum print quality, as well as adjusting the print head and so on, you also need to clean and Replacing replace parts periodically.
  • Page 50 Dip the cleaning stick in the ink cleaner as follows to clean ink stains around the suction cup that you could not wipe off with a dry cleaning stick. Read the safety data sheet before use. You can download the safety data sheet from the Epson Web site. URL: http://www.epson.com...

  • Page 51: Disposing Of Used Consumables And Optional Parts

    SC-F2000 Series User’s Guide Maintenance Pour an appropriate amount of ink cleaner into See the following when disposing of waste ink. the cup supplied with the maintenance kit. “Disposing of Waste Ink” on page 60 Cleaning Caps When it is time to clean the suction cap, a message is displayed on the control panel.
  • Page 52 SC-F2000 Series User’s Guide Maintenance Open the printer cover. Wipe the inside of the suction cap while rotating the thin cleaning stick. If there is a lump or film of waste liquid stuck to the suction cap, remove it with the supplied pair of tweezers.

  • Page 53: Replacing The Head Cleaning Set

    80 unit, anti-drying caps, and then flushing pad. “Replacing the wiper unit/anti-drying caps” Read the safety data sheet before use. You can download the safety data sheet from the Epson Web site. on page 54 URL: http://www.epson.com “Flushing pad” on page 55...
  • Page 54 SC-F2000 Series User’s Guide Maintenance Replacing the wiper unit/anti-drying Wrap the old wiper unit in the packaging of the new wiper unit. caps Open the printer cover. Disposal method The wiper unit is classified as industrial waste. Unpack the new wiper unit.
  • Page 55 SC-F2000 Series User’s Guide Maintenance After installing the wiper unit, replace the Press the lever forwards, and then place the holes anti-drying cap. in the anti-drying cap over the two poles on the printer. Unpack the new anti-drying cap, and then remove the cover.

  • Page 56: Tube Washing

    SC-F2000 Series User’s Guide Maintenance Grip the tab on the flushing pad and remove it. Make sure no waste ink drips from the pad. If any waste ink drips into the printer, make sure you clean it up. Close the printer cover.
  • Page 57 SC-F2000 Series User’s Guide Maintenance White ink mode Press the d/u buttons to highlight White Ink or Color Ink, and then press the r button. Setting (color) New cartridge ❏ White ink White ink x2 Press the d/u buttons to highlight Yes, and then press the Z button.

  • Page 58: Replacing And Shaking Cartridges

    Important: Press the Z button. Epson recommends the use of genuine Epson ink cartridges. Epson cannot guarantee the quality or Press the Z button to start charging the reliability of nongenuine ink. The use of cleaning liquid.
  • Page 59 SC-F2000 Series User’s Guide Maintenance White ink Put your finger into the indentation on top of the ink cartridge and pull it straight out. Important: Removed ink cartridges may have ink around the ink supply port, so be careful not to soil the surrounding area.

  • Page 60: Disposing Of Waste Ink

    SC-F2000 Series User’s Guide Maintenance If you need to replace or shake another ink Caution: cartridge, repeat steps 3 to 5. ❏ Always wear protective eyewear and gloves when applying the liquid. Important: Should any waste ink contact your skin or Install ink cartridges into all slots.

  • Page 61: Replacing The Waste Ink Bottle

    SC-F2000 Series User’s Guide Maintenance Remove the waste ink tube from the used waste Note: ink bottle, and insert it into the new waste ink If you have replaced the waste ink bottle before a message bottle taking care not to spill any waste ink.

  • Page 62: Replacing White Ink

    SC-F2000 Series User’s Guide Maintenance Buttons that are used in the following operations Confirm that the printer is on, and then press the - button. The Maintenance menu is displayed. Press the d/u buttons to highlight Replace Press the Z button.

  • Page 63: Cleaning The Printer

    SC-F2000 Series User’s Guide Maintenance Cleaning the Printer Buttons that are used in the following operations To maintain the printer in optimum condition, you need to perform periodic cleaning. Clean the platen and the platen frame using the same procedure.

  • Page 64: Using The Control Panel Menu

    SC-F2000 Series User’s Guide Using the Control Panel Menu Using the Control Panel Menu Menu Operations The steps for displaying the various menus are shown below. * The operation performed when you press the Z button depends on the selected item.

  • Page 65: Menu List

    SC-F2000 Series User’s Guide Using the Control Panel Menu Menu List The items and options available in the menu are described below. See the reference pages for more details on each item. * High-speed color mode is not supported. Menu...
  • Page 66 SC-F2000 Series User’s Guide Using the Control Panel Menu Menu Setting Item Setting Printer Status Level “Printer Status” on page 69 Head Cleaning Set Firmware Version xxxxxxx,x.xx,xxxx Print Status Sheet Print Administrator Menu Network Setup “Administrator Menu” on IP Address Setting...

  • Page 67: Menu Descriptions

    SC-F2000 Series User’s Guide Using the Control Panel Menu Menu Descriptions USB File List *1 indicates the default settings Setting Item Setting Description Select Print File xxxxxxxxxxxxxxxxxxxxxx x to xxx (1*1) If the data on the connected USB memory stick is supported, the name of the data file is displayed with up to 23 single-byte characters.

  • Page 68: Printer Setup

    SC-F2000 Series User’s Guide Using the Control Panel Menu Setting Item Setting Description Tube Washing White Ink*1 *2 Removes sediment that has accumulated in the selected ink tube. For White Ink, a message is displayed when it is time to Color Ink perform maintenance.

  • Page 69: Print Logs

    SC-F2000 Series User’s Guide Using the Control Panel Menu Setting Item Setting Description Head Alignment If print results are grainy or blurry, perform Head Alignment to realign the print head for each platen size. Visually inspect the printed check pattern, and then enter the adjustment value for the pattern with the least visible lines.

  • Page 70: Administrator Menu

    SC-F2000 Series User’s Guide Using the Control Panel Menu Setting Item Setting Description Firmware Version xxxxxxx,x.xx,xxxx Displays the printer's firmware version. Print Status Sheet Print Prints a list of the current setting statuses for the printer. Choose this option to view settings at a glance.

  • Page 71: Maintenance Mode

    SC-F2000 Series User’s Guide Using the Control Panel Menu Setting Item Setting Description Date & Time YY/MM/DD HH:MM Set the printer's built-in clock. The time is used when printing the job log and printer status. MM/DD/YY HH:MM Language Japanese Select the language used on the control panel's screen.
  • Page 72 SC-F2000 Series User’s Guide Using the Control Panel Menu Setting Item Setting Description Sleep Mode The printer enters sleep mode automatically when there are no errors, no print jobs being received, and no control panel or 5 to 180 minutes later other operations are performed for the selected period.

  • Page 73: Problem Solver

    SC-F2000 Series User’s Guide Problem Solver Problem Solver What to Do When a Message Is Displayed If the printer displays one of the messages shown below, refer to the solution listed and take the necessary steps. Message What to do ❏...

  • Page 74: When A Maintenance Call/Service Call Occurs

    Turn the printer on and off several times. If the same call for service is displayed on the LCD panel, contact your dealer or Epson Support for assistance. Tell them the call for service code is "XXXX".

  • Page 75: Troubleshooting

    SC-F2000 Series User’s Guide Problem Solver You cannot print in the network Troubleshooting environment. You cannot print (because the Are the network settings correct? Ask your network administrator for the network printer does not work) settings. The printer does not turn on.

  • Page 76: Print Results Are Not What You Expected

    There is no problem if the rows you cannot see are printed with the cleaning liquid. Are you using genuine Epson ink cartridges? This printer is developed for use with Epson ink cartridges. If you use non-Epson ink cartridges, the Are you printing on paper in White ink mode? print result may be faint, or the color of the printed It is hard to see White ink when it is printed on paper.
  • Page 77 SC-F2000 Series User’s Guide Problem Solver Have you compared the printing result with Adjust the density of the White ink. the image on the display monitor? When printing on dark colored T-shirts, vertical unevenness may occur depending on the base color.

  • Page 78: Others

    SC-F2000 Series User’s Guide Problem Solver Have you shaken White ink cartridges? Have you washed the ink tubes? Because the ink particles in White ink can sediment Because the ink particles in White ink can sediment easily, it needs to be shaken at the start of every...

  • Page 79: Printing Is Slow

    SC-F2000 Series User’s Guide Problem Solver Platen Height Error is displayed while Printing is slow printing Is the head move direction set to uni-directional? Are you printing data over the entire print Head Move Direction may be set to Uni-Directional...

  • Page 80: Appendix

    * Epson recommends the use of genuine Epson ink cartridges.Epson cannot guarantee the quality or reliability of non-genuine ink. The use of non-genuine ink may cause damage that is not covered by Epson’s warranties, and under certain circumstances, may cause erratic printer behavior.Information about non-genuine ink levels may not be displayed, and use of non-genuine ink is recorded for possible use in service support.
  • Page 81 SC-F2000 Series User’s Guide Appendix Others Product name Product Explanation number Cleaning cartridge T7360 For washing the print head and washing the tubes. Pre-treatment Liquid T7361 20 liters. Dilute before use. “Using Pre-treatment Liquid” on page 27 Maintenance Kit T7362 The same as the maintenance kit supplied with the printer.

  • Page 82: Notes When Moving Or Transporting The Printer

    SC-F2000 Series User’s Guide Appendix Notes When Moving or Preparing to Move Transporting the Printer This section explains how to move the printer on the same floor without any changes in the floor level. See the following for instructions on moving the printer to This section explains how to move or transport the another floor or building.

  • Page 83: Setting Up The Printer After Moving

    SC-F2000 Series User’s Guide Appendix Adjust the print head misalignments, and then check the print quality. “Correcting the print misalignment” on page 47 Transporting the Printer When transporting the printer, protect the printer from shock and vibration using the protective materials and packing materials used when it was initially delivered after preparing the printer for the move.

  • Page 84: System Requirements

    SC-F2000 Series User’s Guide Appendix System Requirements Specifications Table The following describes the system requirements Printer Specifications necessary to install and use the software for this printer. Printing method On-demand ink jet Windows Nozzle configuration Operating System Windows XP/Windows Vista/...
  • Page 85 SC-F2000 Series User’s Guide Appendix Printer Specifications Important: Do not refill the ink. Operating temperature/humidity Cleaning cartridge specifications Expiry date See the date printed on the package (at normal temperature) Temperature Operating: 10 to 35 °C In storage (in package) and after installation in printer: -20 to 40 °C (within 4 days at -20 °C, a...

  • Page 86: Standards And Approvals

    SC-F2000 Series User’s Guide Appendix Ink cleaner specifications Capacity 150 ml Standards and Approvals Safety UL 60950-1 CAN/CSA C22.2 No.60950-1 Low Voltage EN 60950-1 Directive 2006/95/ FCC part 15 subpart B Class A CAN/CSA-CEI/IEC CISPR 22 Class A AS/NZS CISPR 22 Class A...

  • Page 87: Where To Get Help

    Support Technical Support Web Before Contacting Epson Site If your Epson product is not operating properly and you cannot solve the problem using the troubleshooting Epson’s Technical Support Web Site provides help with information in your product documentation, contact problems that cannot be solved using the Epson support services for assistance.

  • Page 88: Help For Users In North America

    Internet Support Help for Users in Australia Visit Epson’s support website at http://epson.com/ Epson Australia wishes to provide you with a high level support and select your product for solutions to of customer service. In addition to your product common problems. You can download drivers and...

  • Page 89: Help For Users In Singapore

    The more information you ❏ Product usage questions or problems prepare, the faster we can help solve the problem. This information includes your Epson product ❏ Enquiries on repair service and warranty documentation, type of computer, operating system, application programs, and any information you feel is required.

  • Page 90: Technical Support Hotline

    603-56288222 Internet Home Page ❏ Enquiries on repair services & warranty, product Epson Hong Kong has established a local home page in usage and technical support (Techline) both Chinese and English on the Internet to provide users with the following information:...

  • Page 91: Help For Users In The Philippines

    - 6PM) Prefix local STD code Help for Users in the Philippines To obtain technical support as well as other after sales services, users are welcome to contact the Epson Philippines Corporation at the telephone and fax numbers and e-mail address below:...

  • Page 92: Bonjour

    SC-F2000 Series User’s Guide Software License Terms Software License Terms Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version ("Bonjour Programs"). We provide the source code of the Bonjour Programs pursuant to the Apple Public Source License Version1.2 or its latest version until five (5) years after the discontinuation of same model of this printer product.
  • Page 93 SC-F2000 Series User’s Guide Software License Terms 1.7 "Original Code" means (a) the Source Code of a program or other work as originally made available by Apple under this License, including the Source Code of any updates or upgrades to such programs or works made available by Apple under this License, and that has been expressly identified by Apple as such in the header file(s) of such work;...
  • Page 94 SC-F2000 Series User’s Guide Software License Terms 2.4 Third Party Rights. You expressly acknowledge and agree that although Apple and each Contributor grants the licenses to their respective portions of the Covered Code set forth herein, no assurances are provided by Apple or any Contributor that the Covered Code does not infringe the patent or other intellectual property rights of any other entity.
  • Page 95 SC-F2000 Series User’s Guide Software License Terms 9. LIMITATION OF LIABILITY. TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT SHALL APPLE OR ANY CONTRIBUTOR BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR RELATING TO THIS LICENSE OR YOUR USE OR INABILITY TO USE THE...
  • Page 96 SC-F2000 Series User’s Guide Software License Terms 13.2 Relationship of Parties. This License will not be construed as creating an agency, partnership, joint venture or any other form of legal association between or among You, Apple or any Contributor, and You will not represent to the contrary, whether expressly, by implication, appearance or otherwise.

  • Page 97: Info-Zip Copyright And License

    SC-F2000 Series User’s Guide Software License Terms Info-ZIP copyright and license This is version 2007-Mar-4 of the Info-ZIP license. The definitive version of this document should be available at ftp://ftp.info-zip.org/pub/infozip/license.html indefinitely and a copy at http://www.info-zip.org/pub/infozip/ license.html. Copyright © 1990-2007 Info-ZIP. All rights reserved.

Table of Contents