Related Manuals for Danfoss TS715Si
Summary of Contents for Danfoss TS715Si
- Page 1 MAKING MODERN LIVING POSSIBLE TS715Si Electronic Single Channel Timeswitch with Service Interval Timer Installation Guide Danfoss Heating...
- Page 2 Marketing on 0845 121 7400. Certification Mark Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other printed material. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
-
Page 3: Table Of Contents
TS715Si Electronic Single Channel Timeswitch with Service Interval Timer Index 1.0 Installation Overview ................4 2.0 Product Specifi cation ................4 3.0 Installation 3.1 Wiring .....................5 3.2 DIL Switch Settings ................6 4.0 Advanced Programming Options .............6 5.0 Copy Functions Explained ..............7 6.0 Service Interval Timer ................9 7.0 Wiring Conversions .................10-13... -
Page 4: Installation Overview
• From the top left hand corner of the wallplate, there must be clearances of at least 140 mm to the right, 15mm to the left, 30mm above and 100mm below in order to mount the plug-on module. TS715SI... -
Page 5: Wiring
On 24 volt models power supply must be wired to 230 V A & B on wallplate. fused 3A Please Note: Always switch off mains fi rst and never fi t programmer to a live wallplate. Danfoss Heating... -
Page 6: Dil Switch Settings
2 on/off s each day Option 2 - (Disable or enable auto time change) Press NEXT, then use + or - to change between auto time change enabled to auto time change disabled. Auto time change enabled (Factory setting) Auto time change disabled TS715SI... -
Page 7: Copy Functions Explained
COPY button. The previously fl ashing day will stop fl ashing to indicate it has been de-selected. NOTE: When a day has been copied to, it will remain visible and not fl ashing when the DAY button is used to select other days. Danfoss Heating... - Page 8 1. Programme “A” day events using the + (time advance), - (time decrease), and NEXT (next period) buttons. 2. Press the DAY button to change to programme the “B” days. 3. Programme “B” day events using the + (time advance), - (time decrease), and NEXT (next period) buttons. TS715SI...
-
Page 9: Service Interval Timer
The TS715 Si is fi tted with an installer setback service interval timer. If this feature is required please contact our technical department. Setting instructions for this gas safety feature are only available to bona fi de heating installers. Danfoss Heating... -
Page 10: Wiring Conversions
(Applies only to 230 volt models) Wiring conversions for other timeswitches which can be replaced with the Danfoss TS715-Si, refer to the second part of the table. If in any doubt, please contact our Technical Services Department before proceeding with the replacement. - Page 11 (or pairs of leads) should be SPARE terminated must be reconnected as shown below. In addition, in mains voltage systems, fi t wire acing the following timeswitches. Wiring details are shown below. In addition, in Danfoss Heating...
- Page 12 MAINS DANFOSS RANDALL TS715-Si The TS75/TS15 wallplate must be used to replace the existing wallplate when repla mains voltage systems, fi t wire link between terminal 1 & L of wallplate. SANGAMO M6 SANGAMO 410 FORM 8 SANGAMO S254 FORM 2, S408 FORM 5,...
- Page 13 LOAD An additional terminal block may be required where these disconnected leadss (or pairs of leads) should be SPARE terminated acing the following timeswitches. Wiring details are shown below. In addition, in LOAD SWITCH LOAD LIVE LINE LOAD Danfoss Heating...
- Page 14 TS715SI...
- Page 15 Danfoss Heating...
- Page 16 Danfoss Ltd. Ampthill Road Bedford MK42 9ER Tel: 01234 364621 Fax: 01234 219705 Email: ukheating@danfoss.com Website: www.heating.danfoss.co.uk Part No. 38163v01s7-06 01/11...