About Full Error Codes - Pioneer PDR-555RW Service Manual

11.2 ABOUT FULL ERROR CODES

With the PDR-555RW, PDR-19RW, and PDR-V500, a full error
code is displayed on the FL display when you press the SKIP PLAY
key and MENU key simultaneously.
The full error codes are not backed up, and are cleared when the
power is turned off.
With the PDR-509, press the TIME and DISP OFF keys
simultaneously.
Display
The eight digits are displayed as shown below:
The values of each 2 digits for 1 to 4 (8 digits in total) are shown
below:
Two digits displayed for 1 :
The lower digit shows the operation when
the error is detected.
×0
: Unknown
×1
: Tray open
×2
: Tray close or open
×3
: SETUP (starting up a disc)
×4
: TOC, PMA read (including SETUP)
×5
: PLAY
×6
: SEARCH
×7
: REC/PAUSE
×8
: REC
×9
: LEAD OUT REC
×A
: TOC REC
×B
: PMA REC
×C
: Power calibration
×D
: TOC CHECK
×E
: ACTUAL PAUSE REC
×F
: Unknown
When "F1" is displayed in two digits for 2, the digits for 1 show
the number of the defective pin of the mechanism control.
Two digits displayed for 2 : Error Mode
Errors Generated in the Mechanism Control
Mode : Mode Name
No.
00 : Unfixed mode (inner condition unknown, upon
hardware reset)
01 : Invalid mode
02 : STOP
03 : Laser diode on (playback power)
04 : Focus ON
05 : Spindle ON
06 : Tracking ON
PDR-555RW, PDR-V500, PDR-19RW, PDR-509
07 : Direct sequence forward 1-track jump using DIRC
08 : Direct sequence reverse 1-track jump using DIRC
09 : Direct sequence forward 1-track jump repeat using DIRC
10 : Direct sequence reverse 1-track jump repeat using DIRC
11 : Auto sequence 10-track forward jump repeat
12 : Auto sequence 10-track reverse jump repeat
13 : Auto sequence 50-track forward jump repeat
14 : Auto sequence 50-track reverse jump repeat
15 : Auto sequence forward M-track movement
16 : Auto sequence reverse M-track movement
17 : PAUSE
18 : PLAY
19 : Seek track 0
20 : Blank search
21 : REC
22 : REC to PAUSE (REC END)
23 : ATIP TIME search
24 : Q-code TIME search
25 : Q-code track search
26 : Forward 300-track movement
27 : Reverse 300-track movement
30 : TOC area search
31 : Tray open
32 : Tray close
33 : Setup (→ PLAY)
34 : TOC read
35 : PLAY normal
: Search → PLAY
36
37 : REC. PAUSE
39 : Lead-out REC
40 : TOC (lead-in) REC
41 : PMA REC
42 : PCA REC
43 : TOC check
44 : Actual REC PAUSE
45 : Initializing
47 : 2-track jump setting in pause mode
48 : 1-track jump setting in pause mode
: Search → PAUSE
51
52 : PMA read
53 : Laser diode nominal recording power output
54 : Searching area with Q code
57 : Laser diode maximum recording power output
58 : Laser diode recording power continuous sweep mode
59 : Slider forward movement
60 : Slider reverse movement
61 : Calculating the track pitch and the line velocity of the disc
by measuring T0 and T1.
62 : Auto sequence 1-track forward jump
63 : Auto sequence 1-track reverse jump
47