Cleaning; Conservation For Winter Operation; Storage; Re-Initation After Time Of Storage - KTM 640 LC4 Owner's Manual

Clean your motorcycle regularly in order to maintain the beauty of its plastic surfaces.
The best manner would be to use warm water that has been mixed with a normal trade washing detergent and a sponge. The hard
dirt can be removed before with the help of a soft water jet.
!
N
EVER CLEAN YOUR MOTORCYCLE WITH A HIGH
ELECTRICAL COMPONENTS
DESTRUCTION OF THESE PARTS
– You should use normal trade-mark detergents to clean the engine. Strongly dirted parts should be cleaned additionally with the
help of a paint brush.
– After the motorcycle has been rinsed with a soft water jet, it should be dried by air pressure and a cloth. Then take a short drive
until the engine has reached the working temperature and also use the brakes. Due to the heat, the water also evaporates at the
unapproachable parts of the engine and the brakes.
– Slide back the protective covers on the handlebar-mounted instruments so that any water that may have seeped into this part of
the motorcycle is allowed to evaporate.
– After the motorcycle has cooled down, oil and grease all sliding and pivot points. Treat the chain with a chain spray too.
– To prevent failures in the electric system, you should treat the ignition lock, the emergency OFF switch, light switch and the socket
connectors with contact spray.
In the event that the motorcycle is also used in winter and on roads where one has to expect salt spraying, you will have to take
44
precautions against the aggressive road salt.
– Clean motorcycle thoroughly and let it dry
– Treat engine, carburetor, swing arm, and all other bare or galvanized parts (except for brake discs) with a wax-based anti-corrosion
agent
K -
EEP ANTI CORROSION AGENT FROM GETTING INTO CONTACT WITH THE BRAKE DISCS
.
POWER
!
A
FTER RIDES ON SALTED ROADS
Should you desire to make a pause over a longer space of time, please observe the following instructions:
– Clean motorcycle thoroughly (see chapter: CLEANING)
– Change engine oil, oil filter and fine screen filter (old engine oil contains aggressive contaminations).
– Check antifreezer and amount of cooling liquid.
– Warm up the engine once again, close the fuel cock and wait until the engine dies. Then open the drain plug of the float chamber
to remove the remaining fuel.
– Remove spark plug and fill in approx. 5 ccm of engine oil into the cylinder through the opening. Actuate kick-starter 10 times in
order to distribute the oil onto the cylinder walls and mount the spark plug.
– Set piston to compression so that the valves will be closed (slowly operate the kickstarter, until you can hear the automatic
decompressor click (release)
– Let fuel flow out of tank into an appropriate container.
– Correct tire pressure.
– Lubricate pivot points of the control levers, foot rests, etc. as well as the chain.
– Service the shock absorber linkage
– Disassemble and charge battery (see chapter: BATTERY).
– The storage place should be dry and not subject to excessive temperature fluctuations.
– Cover the motorcycle with an air permeated tarpaulin or blanket. Do not use non air permeable materials as a possible humidity
might not be able to escape and could cause corrosion.
!
I
T WOULD BE VERY BAD TO LET THE ENGINE RUN FOR A SHORT TIME DURING THE STORAGE PERIOD
AND THE THUS DEVELOPED STEAM WOULD CONDENSE DURING THE COMBUSTION PROCESS AND CAUSE THE VALVES AND EXHAUST TO RUST
RE-INITIATION AFTER TIME OF STORAGE
– Mount the charged battery (regard polarity).
– Fill up tank with fresh fuel.
– Check motorcycle as before each start (see driving instructions).
– Take a short, careful test ride first.
NOTE: Before you put your motorcycle away for the winter, you have to check all parts for their function and wear. Should any
service jobs, repairs, or any refitting be necessary, you should have them carried out during the off-season (lower workload at
mechanics' shops). This way, you can avoid the long waiting times at your mechanic at the beginning of the next biking season.
-
PRESSURED CLEANER OR A HIGH
, ,
CONNECTORS SHEATHED CABLES
.

CONSERVATION FOR WINTER OPERATION

,
CLEAN MOTORCYCLE THOROUGHLY WITH COLD WATER AND LET IT DRY WELL

CLEANING

CAUTION
-
PRESSURED WATER JET
, , .
BEARINGS CARBURETOR ETC
WARNING
,
FOR OTHERWISE THIS WILL SIGNIFICANTLY REDUCE THE BRAKING
CAUTION

STORAGE

CAUTION
. T
HE WATER COULD OTHERWISE RUN INTO THE
AND CAUSE DISTURBINGS OR LEAD TO A PREMATURE
!
. T
HE ENGINE WOULD NOT GET WARMED UP ENOUGH
!
!
!
.