Subscribe to Our Youtube Channel
Related Manuals for Team Losi LOSB0103 1/10 HIGHroller RTR
Summary of Contents for Team Losi LOSB0103 1/10 HIGHroller RTR
- Page 1 HIGH ROLLER ROLLER 1/10-SCALE ELECTRIC RTR LIFTED TRUCK LOSB0103 1/10 HIGHroller RTR Not responsible for errors. All prices subject to change without notice. Losi, a Division of Horizon Hobby, Inc.
-
Page 2: Table Of Contents
Table of Contents Safety Warnings and Precautions Introduction NOTICE Batteries and Charging: All instructions, warranties and other collateral documents are • Read all instructions provided by the manufacturer of the Introduction ....................2 We hope you operate this RC model in a safe, reasonable and cau- subject to change at the sole discretion of Horizon Hobby, Inc. batteries prior to use. -
Page 3: Supplied And Required Equipment
Supplied and Required Equipment The Losi 1/10 HIGHroller Overview Eight (8) AA batteries Supplied tools: NiMH battery charger with automatic “peak detection” recommended. 2-Way wrench DYN4044 Vision Peak™ 2 AC/DC Charger Two (2) Hex Wrenches (L shaped) 1/16 and 3/32 Flat Turnbuckle Wrench Recommended Accessories: Hobby grade knife CA glue (LOSA7880 or LOSA7881) Needle nose pliers Side cutting pliers Double-sided tape (LOSA4004) Safety Goggles Soldering iron... - Page 4 The Losi 27MHz AM Radio System Overview 1/10 HIGHroller Electronics System Overview...
- Page 5 MSC 12RB 12T Fwd/Rev ESC Installing Batteries: Transmitter Adjusting the Transmitter Features Remove the battery cover from the bottom of the transmitter by sliding it away from the base of the handle. Install the eight (8) AA size batteries into the base, noting polarity when inserting each battery. • High-power FET control with proportional forward and reverse. 1. Set the “throttle reversing” switch to the NORMAL position. 2.
-
Page 6: Quick Start
Battery Pack(s) Quick Start To install the battery pack remove the battery hold-down strap by removing the clip from the front mounting boss, and then, while Note: Please read the entire manual to gain a full understanding of the 1/10 HIGHroller lifting the strap, pulling forward in one motion. vehicle, fine-tuning the setup and performing maintenance. 1. R ead the safety precautions found on page 3. This is important for your safety and prevention of personal injury. 2. C harge the battery pack you have chosen (NOT INCLUDED). Refer to the manufacturer’s supplied instructions for battery charging information. -
Page 7: Losi 27Mhz Am Radio System
Losi 27MHz AM Radio System Receiver There is no adjustment required of the receiver. Please note the different slots for connection. The Radio System The following is an overview of the various functions and adjustments found on your Losi/HIGHroller radio system. Since the HIGHroller operates on a radio signal, it is important for you to read and understand about all of these functions before driving the model. The Transmitter Steering Rate: Adjusts amount front wheels move when the Steering Wheel: Controls direction (left/right) of the model. steering wheel is turned left and right. Throttle Trigger: Controls speed and direction (forward/ reverse) of the model. ST. REV: Reverses the function of the steering when the wheel is turned left or right. Antenna: Transmits signal to the model. TH. REV: Reverses the function of the speed control when On/Off Switch: Turns the power on/off for the transmitter. -
Page 8: Driving The 1/10 Highroller
Driving the 1/10 HIGHroller How you drive your 1/10 HIGHroller will also affect your run Tuning the Front End of the 1/10 HIGHroller Tuning, Adjusting & Maintaining the times. If you are performing runs, going from a standstill to full 1/10 HIGHroller Shock Location: The 1/10 HIGHroller has three mounting Please note the following precautions before running speed repeatedly, you are asking a lot from your batteries and locations on the front shock tower. The position can be easily your 1/10 HIGHroller. - Page 9 Tuning the Rear End of the 1/10 HIGHroller Inboard Camber Location: The 1/10 HIGHroller has three Outboard Camber Location: In addition to the inboard different inner locations with vertical adjustment for the front camber location, the 1/10 HIGHroller also provides two Shock Location: Moving the shocks in on the arm will result in camber tie rod. In general, the lower or further out the inside outboard mounting options. The outer location helps the 1/10 more forward traction and let the 1/10 HIGHroller drive more position is, relative to the outside, the more camber gain (total HIGHroller stay tighter in turns with a more precise steering square off the turn.
-
Page 10: Troubleshooting Your 1/10 Highroller
Adjusting Gear Mesh Battery Position: This is a critical adjustment that is often Troubleshooting your 1/10 HIGHroller Vehicle runs slowly/slow acceleration: overlooked but can be very useful. Start by running the battery Incorrect gear mesh is the most common cause of stripped spur Check the battery connectors. spaced in the back (standard setup with 6-cell battery pack). gears. To set the gear mesh, one method is to cut a narrow strip Many questions are the result of simple user errors or minor Confirm that the battery is charged. - Page 11 Warranty and Repair Policy warranty repair estimates will be billed a minimum of ½ FCC Information Law: These Terms are governed by Illinois law (without regard hour of labor. In addition you will be billed for return freight. to conflict of law principals). This device complies with part 15 of the FCC rules. Operation is Warranty Period Horizon accepts money orders and cashiers checks, as well as subject to the following two conditions: (1) This device may not WARRANTY SERVICES Visa, MasterCard, American Express, and Discover cards. By...
Need help?
Do you have a question about the LOSB0103 1/10 HIGHroller RTR and is the answer not in the manual?
Questions and answers