Master Effects - Korg OASYS musical instruments Operation Manual

Using Effects
Each time you press the button, the insert effect will
be switched on/off. When Off, the result will be the
same as when 000: No Effect is selected. The input
sound will be output without change.
9. Make Chain settings.
If the Chain check box is checked, the insert effect
will be connected in series. Since the output of the
oscillator is being sent to IFX1 in step 2, making
settings as shown in the diagram step 6 would
connect all five insertion effects IFX1 → IFX2 →
IFX3 → IFX4 → IFX5 in series, so that these effects
would be inserted into the output of the oscillator.
10.Make settings for Pan (CC#8), "Bus Sel. (Bus
Select)," "Send 1," "Send 2," REC Bus and "Ctrl
Bus" for the sound after it has passed through the
insert effects.
If you've specified a chain, the settings that follow
the last IFX in the chain will be valid (except for
"Ctrl Bus").
Pan: Sets the pan of the IFX output.
Bus Sel. (Bus Select): Specifies the output
destination. Normally you will set this to L/R. If
you wish to send the sound that has passed through
the insert effects to AUDIO OUTPUT
(INDIVIDUAL) 1–8, select 1–8, 1/2, or 7/8.
Send 1, Send 2: Sets the send levels to the master
effects. For this example, set this to 127.
Ctrl Bus: The FX Control Buses lets you create
effects "sidechains." Sidechains let you control an
effect with one audio signal (the sidechain), while
the effect processes a completely different audio
signal. This is convenient for use with vocoders,
compressors and limiters, gates, etc. For more
information, see "FX Control Buses" on page 730 of
the Parameter Guide.
REC Bus: The sound processed by the insert effect
will be sent to the REC bus. In the P0– Audio
Input/Sampling page, you can set the Sampling
Setup Source Bus to a REC bus, and sample the
signal that is sent to the REC bus. Use this if you
want to sample only the sound of an audio input
source being processed by an insert effect (and not
sample the sound of the oscillator output).
Alternatively, the direct sound from the audio
inputs can be mixed with the sound processed by an
insert effect, sent to a REC bus, and sampled.
11.Go to the P8: Insert Effect– Insert FX page, and edit
the parameters of the insert effect you selected.
Press the IFX 1–12 tab, use the tabs at the left to
select IFX1–12, and edit the effect parameters.
186
Effect On/Off
Wet/Dry Effect Parameters
Effect 1 On/Off: Turns the insert effect on/off. This
is linked with the on/off setting in the Insert FX
page.
P (Effect Preset): Selects an effect preset. The
OASYS' internal memory contains "effect presets"
which are parameter settings for each effect from
001: St.Dyna Compressor through 185: Mt.BPM
Dly//Mt.BPM Dly.
Effect parameters you edit are saved as part of each
program, but effect presets allow you to save
favorite parameter settings for each effect. If you've
come up with an effect setting you like, use the page
menu command "Save to User Preset" to save it as a
preset so that you can easily recall it in a different
program or mode.
For details on the individual effects, see:
• "Dynamics" on page 764 of the Parameter Guide
• "EQ and Filters" on page 773 of the Parameter
Guide
• "Overdrive, Amp models, and Mic models" on
page 788 of the Parameter Guide
• "Chorus, Flanger, and Phaser" on page 797 of the
Parameter Guide
• "Modulation and Pitch Shift" on page 809 of the
Parameter Guide
• "Delay" on page 829 of the Parameter Guide
• "Reverb and Early Reflections" on page 849 of the
Parameter Guide
• "Mono-Mono Serial" on page 854 of the Parameter
Guide
• "Mono/Mono Parallel" on page 877 of the
Parameter Guide

Master effects

12.The input levels to the master effects are set by the
"Send 1, 2" levels (step 3 or 10). If "Send 1, 2" are
zero, the master effects will not apply. "Send 1"
corresponds to MFX1, and "Send 2" corresponds to
MFX2.
13.Access the Program P9: Master/Total Effect–
Routing page.
P (Effect preset)