Table of Contents
Advertisement
The power inverter output waveform
The ac output waveform of the power inverter is known as a
"modified sine wave".
This type of waveform is suitable for most ac loads, including
linear and switching power supplies used in electronic
equipment, transformers and motors.
Use
Locate the power inverter securely in the cup-holder making
sure that it does not interfere with normal operation of the
vehicle, ie gear stick, handbrake etc.
Note: Make sure that the fan (4) is not obstructed in any way.
Power source requirements
The power source must provide 12 Vdc and must be able to
supply the necessary current to operate the load.
Warning! The power inverter must be connected only to
batteries with a nominal output voltage of 12 Volts. The
appliance will not operate from a 6 Volt battery and will
sustain permanent damage if connected to a 24 Volt battery.
Connection to a power source
The power inverter comes equipped with a 12 Vdc
accessory plug (3) for connection to a dc power source.
Note: For optimal performance make sure that the engine is
running while operating the inverter. However, the power
inverter may not operate while the engine is starting because
the battery voltage can drop substantially during cranking.
Connecting to a power source using the 12 Vdc
accessory plug (fig. A and B)
The 12 Vdc accessory plug (3) is suitable for operating the
power inverter at power outputs up to 100 Watts only. The tip
of the plug is positive (+) and the side contact is negative (-).
Note: Connect the power lead supplied with the product into
the socket on the inverter.
Connect the power connector (6) into the socket (7).
Connect the power inverter to the power source by
inserting the 12 Vdc accessory plug (3) firmly into the
accessory outlet of a vehicle or other dc power source.
Note: On some vehicles the accessory socket may only
become live when the ignition key is in the accessory
position.
Insert the mains plug from the appliance to be operated
into the mains socket (1) on the inverter and operate as
normal.
Warning! Do not use with positive ground electrical
systems, (i.e older vehicles).
Warning! A reverse polarity connection will result in a blown
fuse and may cause permanent damage to the power
inverter.
4
Once you have finished using the inverter make sure
that you remove the 12 Vdc accessory plug (3) from the
12 Vdc source.
Warning! Loose connectors may cause overheated wires
and melted insulation. Check to make sure you have not
reversed the polarity. Damage due to reversed polarity is not
covered by our guarantee.
Your inverter will power/recharge small personal electronic
items rated up to 100W:
MP3 players
Mobile phones
Note: Some mobile phones leads do not allow charging from
a standard USB port, check with the mobile phone
manufacturer.
PDAs
Digital cameras and video cameras
Laptops
Connecting devices to your inverter
AC devices
The power inverter is equipped with a standard mains
socket (1). Plug the cord from the equipment you wish to
operate into the mains socket (1). Make sure that the load
requirement of your equipment does not exceed the rated
wattage indicated on the unit.
Note: Some power supplies may not operate with this
inverter due to the inrush currents required to start those
devices. The inverter will shut down in overload mode.
USB devices (fig. C)
The power inverter is equipped with a standard USB port (5).
Plug the USB connector from the equipment you wish to
operate into the USB port (5).
Note: Some mobile phones leads do not allow charging from
a standard USB port, check with the mobile phone
manufacturer.
The power inverter is fitted with overload protection and will
shut down if a load in excess of the rated load is applied.
To restart the appliance after a shut down due to
overloading, remove the overload and reset by
disconnecting from the dc power source and then reconnect.
Warning! This appliance will not operate high wattage
appliances or equipment that produce heat, such as hair
dryers, microwave ovens and toasters.
Protective features of the power inverter
Your appliance monitors the following potentially hazardous
conditions:
Low voltage protection. This condition is not harmful
to the appliance but could damage the power source.
The appliance will automatically shut down when the
Advertisement
Table of Contents
