1. Manuals
  2. Brands
  3. Northern Manuals
  4. Power Tool
  5. 999320
  6. Owner's manual

Northern 999320 Owner's Manual

Electric rebar cutter
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
E L E C T R I C R E B A R C U T T E R
OWNER'S MANUAL
WARNING:
Read carefully and understand RULES FOR SAFE OPERATION and instructions
before operating. Failure to follow the safety rules and other basic safety precautions
may result in serious personal injury.
It e m # 9 9 9 3 2 0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 999320 and is the answer not in the manual?

Questions and answers

Related Manuals for Northern 999320

Summary of Contents for Northern 999320

  • Page 1 E L E C T R I C R E B A R C U T T E R OWNER’S MANUAL WARNING: Read carefully and understand RULES FOR SAFE OPERATION and instructions before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.

  • Page 2: Intended Use

    If you have any questions relative to a particular application, DO NOT use the machine until you have first contacted Northern Tool + Equipment to determine if it can or should be performed on the product.

  • Page 3: Work Area

    WARNING: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. SAVE THESE INSTRUCTIONS WORK AREA Keep work area clean and well lit.

  • Page 4: Tool Use And Care

    or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing of jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

  • Page 5: Operation

    results in personal injury. Keep handle dry, clean and free from oil and/or grease. Keep housing and piston free of dirt and iron filings. Check that no screws or bolts are loose or missing. Following instruction for maintenance. Inspect switch, cord, plug and any extension cable at regular intervals.

  • Page 6: Maintenance

    Fig. 1 Cutting 1. Be especially careful when cutting off short lengths (12 inches or less) as the but end tends to fly out. CAUTION: Flying ends are a hazard to all personnel in the vicinity. Erect safety screens. 2. Do not cover air vents. If the events are covered, motor will overheat and may burn out. 3.
  • Page 7 2. Wipe or brush away all dirt and metal filings. Pay particular attention to the lower half of the piston, where dirt is more easily accumulated. Hydraulic Oil Level Check As the cutters are hydraulically operated, the hydraulic oil level must be checked at frequent intervals, preferably every results in a drop in pressure and loss of cutting power.

  • Page 8: Carbon Brushes

    Carbon Brushes Inspect the two carbon brushes at least once every two months. (Nominal brush life is 200 hours). Worn brushes will result in loss of power, cause the motor to run hot and irreparably damage the armature’s commutator. 1. Disconnect unit from power supply. 2.

  • Page 9: Diagram & Parts List

    DIAGRAM & PARTS LIST Page of 11...
  • Page 10 ITEM SPECIFICATION ITEM SPECIFICATION Cylinder Spring washer M5 Ball bearing Cap bolt M5*18 Piston Cutter block Return spring Spring washer M5 Valve Cap bolt M5*5 Spring valve Locking spring Spring guide Stopper bolt M10*40 Pump seal plug Side handle Magnet filter Sticker Pump case gasket Bearing guide...
  • Page 11 Northern Tool + Equipment Co., 2800 Southcross Drive West P.O. Box 1499 Burnsville, MN 5337-0499...

Table of Contents