Hitachi 42PD9800TA Service Manual page 20

Adj.
No.
535 Reserved
536 Reserved
537 Reserved
538 Reserved
539 Reserved
540 Reserved
541 Reserved
542 Reserved
543 Reserved
544 Reserved
545 Reserved
546 Reserved
547 Reserved
548 Reserved
549 Reserved
550 Reserved
551 Reserved
552 Reserved
553 Reserved
554 RF-PAL IF compensation Enable 0:Disable, 1:Enable
555 DTT Force Reset 5:Yes(Reset), 0～4,6,7:No(Normal),
556 Sub system Busy Check 0:Disable, 1:Enable
557 Sub system Blanking (for DEBUG 0:Normal, 1:Main, 2:Sub, 3:Both)
558 HDMI Output clock invert 0:Normal(Rising edge), 1:Invert(Falling edge)
559 HDMI OUTPUT FORMAT (0:RGB4:4:4, 1/2:YCbCr4:4:4)
560 Sub system status [00h]: Signal, Panel frame rate, Color system
561 Sub system status [01h]: Input signal mode
562 Sub system status [02h]: H.Freq.(H)
563 Sub system status [03h]: H.Freq.(L)
564 Sub system status [04h]: V.Freq.(H)
565 Sub system status [05h]: V.Freq.(L)
566 Sub system status [06h]: V.Total(H)
567 Sub system status [07h]: V.Total(L)
568 Sub system status [08h]: (OSD mode)
569 Sub system status [09h]: (Factory menu)
570 Sub system status [0Ah]: Teletext status(H)
571 Sub system status [0Bh]: Teletext status(L)
572 Sub system status [0Ch]: WSS info.
573 Sub system status [0Dh]: CNI code(H)
574 Sub system status [0Eh]: CNI code(L)
575 Sub system status [0Fh]: NI code(H)
576 Sub system status [10h]: NI code(L)
577 Sub system status [11h]: Version(H)
578 Sub system status [12h]: Version(L)
579 Sub system "Status-read" request available (0:No 1:Yes)
580 Sub system "OSD-packet" refresh available (0:No 1:Yes)
581 Sub system "Control-packet" refresh available (0:No 1:Yes)
582 Inp.Mode (0-2:AUTO, 3-10:576i/480i/576p/480p/720p60/1080i50/60/720p50
583 Sub system H.B. stop count
584 Force Sub Video Decoder ON mode
585 No signal Power-ON DEBUG mode
586 Panel Blanking Enable (when the input signal is changed)
587 Input H.Freq.(Subsys-02&03h / 10) * cutoff below decimal point (31.5kHz -> "31"
588 Input V.Freq.(Subsys-04&05h / 10) * cutoff below decimal point (59.9Hz -> "59"
589 IIC BUS Data/Clock Open(0:Close, 1:Open)
590 HDMI EDID WRITE ENABLE
591 PDP-BLK ON/OFF
592 RS232C Terminal control mode
593 Reset function of accumulation time for LCD Panel
594 Accumulation time for Panel (hours)
595 Display of Panel map version
596 W/B Initialize
597 Gain adjustment (Calibration)
598 EEPROM Initialize(0:No, 1:Yes)
599 Enter to adjust menu(2)
600 Enter to service menu of Sub-system
42PD9800TA (FW1)
Function
ADJ. Items
0:Terminal, 1:Genesis, 2:DTT(Write)
Mode
* YCbCr4:2:2 unused (9/1)
1:ON, 0:OFF
Reserved for Australia DTT
0:Normal 1:Reset
20
Max. Init.
Device
Value Value
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
1 0 Subsys
7 0 -
1 1 -
3 0 Subsys
1 0 HDMI
2 2 HDMI
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
- - -
1 1 -
1 0 -
1 0 -
10 0 -
254 0 -
1 0 -
1 0 -
1 0 -
- - -
- - -
1 0 M30627
1 0 M30627
1 0 PDP
2 1 M30627
1 0 M30627
65535 - PDP
255 - PDP
1 - M30627
1 - -
1 0 M30627
- - M30627
- - FLI8538