GRAPHTEC FC8000 Series User Manual page 264

Cutting pro
Hide thumbs Also See for FC8000 Series:
Table of Contents

Advertisement

16
INDEX
Symbols
(Cross Cut) ................................................................... 3-14
(Front Loading) ............................................................... 2-9
Numerics
2-pen .............................................................................. 1-3
2POINTS.................................................................. 5-6, 6-2
2POINTS....................................................................... 5-12
3POINTS.................................................................. 5-6, 6-2
4POINTS.................................................................. 5-7, 6-2
AlphabetGroup
A
accessory ....................................................................... 1-2
AC line inlet .................................................................... 1-4
AC power cord, 2/3 prong adapter ................................ 1-2
Adjusting for the Registration Mark Scan Position ....... 5-24
Adjust Manually ............................................................ 5-36
Adjustment Marks........................................................... 6-2
Adjust the Blade Length Automatically ........................ 2-36
Adjust the Blade Length Manually ............................... 2-31
Advanced Registration Mark Sensing System............... 5-1
After Turning on the Plotter................................................ v
Aligning the Push Roller ............................................... 2-13
Aligning the Push Rollers ............................................. 2-13
Alignment registration mark ........................................... 5-8
Apparel (AP) Mode....................................................... 4-14
Area sorting .................................................................... 8-2
Assembling ..................................................................... 1-5
Assembling the Stand .................................................... 1-6
Attaching a T ool .............................................................. 2-4
Attaching the Loupe ..................................................... 14-2
Automatically Adjust ..................................................... 5-34
Automatically Cross Cut ............................................... 3-16
Automatic Pre Feed........................................................ 8-4
axes adjustment (3POINT detection) ............................. 5-7
axes adjustment (4POINT detection) ............................. 5-7
axis adjustment (2POINT detection) .............................. 5-7
Axis Alignment, Cut Area ............................................. 14-2
B
Blade Application and Features..................................... 2-3
C
Changing and Storing RS-232C Settings....................... 9-7
Changing CONDITION No. ............................................ 3-6
Changing the Hold-down Force ................................... 2-14
Circle-Command Resolution Setting ............................ 11-9
Cloth basket ................................................................... 1-9
Command ..................................................................... 11-2
Confrm the Cutting Data............................................ 13-19
Connecting with Network (LAN) ..................................... 9-3
Connecting with RS-232C.............................................. 9-6
Contents of Operation from CONDITION Key.............. 2-19
Contents of Operation from Menu Screen.................... 2-19
Continuously Move Manually.......................................... 3-3
Control Keys ................................................................. 2-17
Control Panel................................................................ 2-17
Control panel .................................................................. 1-3
control panel................................................................. 10-7
Copy (Duplicate Cutting)................................................ 4-9
COPY key ..................................................................... 2-17
Cross Cut...................................................................... 3-16
Cross Cut Force ........................................................... 3-17
Cross Cut Manually ...................................................... 3-15
Cut Line Pattern............................................................ 7-15
Cut off the Roll Sheet (Cross Cut) ................................ 3-14
Cutter Blades..................................................................... iv
Cutter Pen....................................................................... 2-2
Cutter Pens........................................................................ iv
Cutting Area ................................................................... 4-2
cutting area .................................................................... 4-4
cutting area, ................................................................... 4-4
Cutting groove ................................................................ 1-3
Cutting mat ..................................................................... 1-3
Cutting T ests ........................................................ 2-34, 2-35
Cut Width...................................................................... 3-14
D
Display Language Setting ............................................ 10-2
Distance Adjust ............................................................ 7-13
Distance Adjustment Between the Registration Mark .. 5-14
Dual Confguration ........................................................ 4-12
E
each cutter blades ....................................................... 2-27
Enabling/Disabling 1/2 Pen Check (CHECK TOOL) .. 14-16
Enabling/Disabling the ":" and ";" Commands
(COMMAND ":",";") ...................................................... 11-6
Enabling/Disabling the Media Sensors
(MEDIA SENSOR)...................................................... 10-4
Enabling/Disabling the Pen Select Command ............. 11-4
Enabling/Disabling the Push Roller Sensors................ 10-5
enlarge/shrink scale ....................................................... 4-8
ENTERkey.................................................................... 2-17
F
Fan Suction Setting ...................................................... 10-6
Force ............................................................................ 3-17
G
GP-GL Command ................................................ 11-5, 13-6
GP-GL Command Error Display ................................... 13-4
Grit roller......................................................................... 1-3
Grit roller position guide ................................................. 1-3
Guideline to Set Offset ................................................. 2-27
Guideline to Set Pouncing ............................................ 2-27
H
How to Use Control Panel ............................................ 2-17
HP-GL............................................................................. 3-9
HP-GL Command ................................................ 11-8, 13-7
HP-GL Command Error Display ................................... 13-4
16-1

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents