Panasonic SC-BT105 Operating Instructions Manual page 42

Troubleshooting guide
Sound
No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.
Humming is heard during play.
No surround sound.
Cannot switch audio.
Card
The capacity of the SD card
decreased.
MPEG-2 motion pictures and
music on an SD card cannot be
played.
The contents of the card
cannot be read.
iPod operation
Cannot charge or operate.
Cannot display iPod videos/
photos on the TV.
Radio
Distorted sound or noise is
heard. "ST" flickers or does not
light.
A beat sound is heard.
A low hum is heard during AM
broadcasts.
Wireless system
No sound
The indicator on the wireless
system keeps flashing between
red and green.
RQT9252
42
≥Turn the volume up.
≥Turn the muting off.
≥Check connections to speakers and other equipment.
≥Press [N, O SELECT] to select the corresponding source.
≥Press [AUDIO] to select the audio.
≥Ensure the speaker settings for your speakers are correct.
≥To output audio from a device connected with an HDMI cable, set "HDMI Audio Output" to
"On" in the Setup menu.
≥When "BD-Video Secondary Audio" is set to "On", Dolby TrueHD, Dolby Digital Plus,
DTS-HD Master Audio and DTS-HD High Resolution Audio are output as Dolby Digital.
≥Audio may not be heard when more than 3 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥[DivX[ Audio may not be output due to how files were created.
≥Ensure that surround selector at the rear of the wireless system is set to the center position.
≥An AC mains lead or fluorescent light is near the main unit. Keep other appliances and cables
away from the main unit.
≥Press [ÎPLIIx] to turn on Dolby Pro Logic IIx/Dolby Pro Logic II.
≥Press [NEO:6] to turn on DTS NEO:6.
≥There are discs for which audio cannot be changed because of how the disc was created.
≥When a BD-Video that supports the virtual package is used, and an SD card is in the slot,
data may be written to the SD card. Erase the data by using "BD-Video Data Erase", format
the card or use a new card.
≥Data that can be played from an SD card are AVCHD and JPEG data.
≥The card is not compatible or the contents on the card may be damaged.
≥Turn off and then turn on the unit again.
≥Check that the iPod is connected firmly.
≥The battery of the iPod is depleted. Charge the iPod, and then operate again.
≥Make sure that TV is connected to the VIDEO OUT terminal on this unit.
≥Operate the iPod menu to make the appropriate video/photo output settings for your TV.
(Refer to operating instructions for your iPod.)
≥Adjust the position of the antenna.
≥Use an outdoor antenna.
≥Turn the TV off or move it away from the unit.
≥Separate the antenna from other cables.
≥Ensure that the digital transmitter is fully inserted into the slot of the main unit.
≥Ensure that the wireless system is plugged into the household mains socket and is turned on.
Then, check that "[W2S]" or "[W4S]" is displayed on the main unit's display.
≥Ensure that surround selector at the rear of the wireless system is set to the center position.
≥Perform the steps below.
1 While pressing the [9/5] on the main unit, press the
numbered button [3] on the remote control until "P" lights in
the main unit's display.
≥The indicator on the wireless system turns green.
2 While "P" is displayed, press [I/D SET] on the rear of the
wireless system.
≥If "P" goes off before you press [I/D SET], repeat step 1
and then continue the procedure.
3 While pressing [9/5] on the main unit, press the numbered button [3] on the remote
control.
≥"[W2S]" or "[W4S]" lights on the main unit.
4 Turn off and on the wireless system.
≥Make sure the indicator on the wireless system lights up green.
≥There is a power supply problem. Consult the dealer.
Page
I/D SET
Use a pointed
object.
16, 17
18
4, 7–9
12
18
35, 37
36
35
—
—
7
—
29
29
—
26
16
14
—
22
—
8
—
—
9
—
—
7
9, 10
7
—
—