Panasonic SC-BT105 Operating Instructions Manual page 41

TV screen and video
Picture stops.
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
The images from this unit do
not appear on the TV.
Picture is distorted.
The screen changes
automatically.
Video is not output in high
definition.
The Setup menu cannot be
accessed.
Status messages do not
appear.
There is a lot of after-image
when playing video.
When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.
There is no apparent change in
picture quality when adjusted
with the "Picture" menu in the
on-screen menu.
The masked-off area is masked
in gray.
≥[DivX[ Picture may stop if the DivX file are greater than 2 GB.
≥Use the TV to change the aspect. Refer to your TV's operating instructions.
≥When using an HDMI cable, set "TV Aspect" to "16:9".
≥When using a component video cable, set "Progressive" to "Off". If the situation is not
restored after that, set "TV Aspect" to "4:3 Pan & Scan".
≥Make sure that the TV is connected to the VIDEO OUT terminal, COMPONENT VIDEO OUT
terminals or HDMI AV OUT terminal on this unit.
≥Make sure that the TV's input setting (e.g., AV 1) is correct.
≥To output video from a device connected with an HDMI cable, set "HDMI Video Mode" to "On"
in the Setup menu.
≥If "BD-Video 24p Output" is turned "On" when the unit is connected to a TV through any
terminal other than HDMI, images may not display properly. In this case, turn "BD-Video 24p
Output" to "Off".
≥When "BD-Video 24p Output" is set to "On", HDMI authentication takes place where 24p
images switch to other images, and a black screen is displayed.
≥When you use the HDMI AV OUT terminal for video output, press and hold [1] (Play) and
[∫] (Stop) simultaneously on the unit for more than 5 seconds to shift the mode to one more
compatible with HDMI equipment.
≥Picture may not be seen when more than 3 devices are connected with HDMI cables.
Reduce the number of connected devices.
≥An incorrect resolution is selected in "Component Resolution", when the TV is connected to
COMPONENT VIDEO OUT terminals. While stopped, press and hold [1] (Play) and
[∫] (Stop) on the unit at the same time for more than 5 seconds to cancel this setting. Set the
item again.
≥The unit and TV are using different video systems. While stopped, keep pressing [∫] (Stop)
and [< OPEN/CLOSE] on the unit for 5 or more seconds. The system switches from PAL to
NTSC or vice versa.
≥The system used on the disc doesn't match your TV.
– PAL discs cannot be correctly viewed on an NTSC TV.
– This unit can convert NTSC signals to PAL60 for viewing on a PAL TV ("NTSC Contents
Output" in the "Picture" menu).
≥[DivX[ Images may not be output due to how files were created.
≥Mobile telephone chargers can cause some disturbance.
≥If you are using an indoor TV antenna, change to an outdoor antenna.
≥The TV antenna wire is too close to the unit. Move it away from the unit.
≥When the "Screen Saver Function" in the Setup menu is set to "On", the display may return to
the screen saver mode automatically if there is no operation for 10 minutes or more.
≥High definition video cannot be output through the VIDEO OUT terminal.
≥Confirm that the "HDMI Video Mode", "HDMI Video Format", and "Component Resolution" in
the Setup menu are set properly.
≥The video output resolution is restricted to "576p/480p" when DVD-Video, DivX and
BD-Video discs recorded at a rate of 50 frames per second is output from the COMPONENT
VIDEO OUT terminals.
≥Select "BD/DVD/CD" or "SD" as the source.
≥Select "Automatic" in "On-Screen Messages" in the Setup menu.
≥Turn "3D NR" or "Integrated NR" off if it is on.
≥When you use the COMPONENT VIDEO OUT terminal for video output, set "Progressive" of
"Picture" menu on the on-screen menu to "Off". This problem is caused by the editing method
or material used on DVD-Video, but should be corrected if you use interlace output.
≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.
1 Connect this unit to the TV with any cable except the HDMI cable.
2 When you connect with the Component Video cable, set "HDMI Video Mode" to "Off" and
"Component Resolution" to "576i/480i" in the Setup menu.
≥The effect is less perceivable with some types of video.
≥If the "Screen Saver Function" in the Setup menu is set to "Off", the masked-off area is
displayed in black.
Page
—
—
36
33, 36
7, 8
—
36
36
36
—
—
36
—
—
35
—
—
—
—
35
—
36
—
—
35
33
33
36
—
35
(Continued on next page)
RQT9252
41