Sony STR-DE598 Service Manual page 3
Fm stereo/fm-am receiver
Hide thumbs
Also See for STR-DE598:
- Service manual (88 pages) ,
- Operating instructions manual (57 pages) ,
- Specifications (2 pages)
Table of Contents
Advertisement
General
Power requirements
Area code
Power requirements
US, CND
120 V AC, 60 Hz
AEP, UK
230 V AC, 50/60 Hz
AUS
240 V AC, 50 Hz
AR, KR
220 – 230 V AC, 50/60 Hz
E2
120/220/240 V AC, 50/60 Hz
TW
110 V AC, 50/60 Hz
Power consumption
Area code
Power consumption
DE598: US, AEP,
220 W
UK, E2, AUS, KR, AR
DE598: CND
300 VA
DE598: TW
500 W
DE698/DV10: US,
230 W
AEP, UK, E2, AUS, AR
DE698: CND
310 VA
Power consumption (during standby mode)
0.2 W
AC outlets (DE698: EXCEPT E2/DV10)
Area code
AC outlets
US, CND
1 switched, 120 W/1A MAX
AEP, UK, E2, AUS
1 switched, 100 W MAX
Dimensions (w/h/d) (Approx.)
DE598:
430 × 157.5 × 310 mm
× 6
× 12
(16
7/8
2/8
2/8
inches) including
projecting parts and
controls
DE698/DV10:
430 × 157.5 × 370 mm
(16
× 6
× 14
7/8
2/8
4/8
inches) including
projecting parts and
controls
Mass (Approx.)
DE598:
8.0 kg (17 lb 11 oz)
DE698/DV10:
9.0 kg (19 lb 14 oz)
Supplied accessories
FM wire antenna (1)
AM loop antenna (1)
Remote commander RM-AAU001 (1) (DE598/DV10)
Remote commander RM-AAP001 (1) (DE698)
R6 (size-AA) batteries (2)
Design and specifications are subject to change
without notice.
• Abbreviation
CND : Canadian model
E2
: AC 120 V area in E model
AUS : Australian model
AR : Argentina model
KR : Korean model
TW : Taiwan model
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
STR-DE598/DE698/DV10
Ver. 1.1
SAFETY CHECK-OUT (US MODEL)
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indica-
tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)
To Exposed Metal
Parts on Set
AC
0.15 µF
1.5 kΩ
voltmeter
(0.75 V)
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES
SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT.
NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES
SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL
OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Page 3
- Quick Links:
- Test Mode
- Block Diagram - Power Section
Hide quick links:
Advertisement
Table of Contents
