JVC KD-NX901 Service Manual page 29

A
Data Read
1.Error History
2.Temperature
3.GYRO adjust value
Data Read Mode
Error logs and data display
Data Clear
1.DVD Err Clr 4.Initial Name & DVD
2.CDCH Err Clr 5.Initial GYROData
3.P-Mecha Err Clr 6.Initial All
Data Clear Mode
Running Mode (For technical examination)
HDD Format
1.Music Srv Format
2.SYS Data Format
HDD Format Mode
DVD Area/Region Area suffix is [E]. Region [2] fixed.
DVD Check Mode
Press Any Key *Refer to DVD CHECK MODE.
DVD Check Mode
DVD NTSC/PAL (For technical examination)
TMC Check Mode TMC Signal Check (Using factory setup)
TMC Info Mode (For technical examination)
Self Check Self check as following
Self Check OK ! GYRO check
ERROR XXXX Check of GYRO data in state of rest.
Self Check Check of GYRO data in AD value.
GPS check
Check of GPS output.
Check of UART output form GPS unit.
HDD check
Check of R/W on the HDD.
Error code
0004: GYRO error
0005: GPS error
0007: HDD error
Note: After self checked should push the [RESET] key, Note: After self checked should push the [RESET] key,
or should pull out a power code 30 seconds or more, and should surely reset a main unit. or should pull out a power code 30 seconds or more, and should surely reset a main unit.
Full Clear Continuously execute of the [Initial All] and [HDD Sev Format].
(Using factory setup)
Note: After cleared should push the [RESET] key, Note: After cleared should push the [RESET] key,
or should pull out a power code 30 seconds or more, and should surely reset a main unit. or should pull out a power code 30 seconds or more, and should surely reset a main unit.
Error History
1.DVD Error 4.System Error
2.CDCH Error
3.Panel Mecha Err
Error History
DVD Error
E-1 :****** E02 :******
E-2 :****** E03 :******
E-3 :****** E04 :******
E01 :****** E05 :******
DVD Error
CDCH Error
E-1 :****** E02 :******
E-2 :****** E03 :******
E-3 :****** E04 :******
E01 :****** E05 :******
CDCH Error
P-Mecha Error
E-1 :****** E02 :******
E-2 :****** E03 :******
E-3 :****** E04 :******
E01 :****** E05 :******
P-Mecha Error
System Error
TOTAL ERROR :**
E-1 :
E-2 :
E-3 :
System Error
Temperature Temperature data. (For technical examination)
GYRO Adjust Value
GYRO Adjust - OK GYRO adjusting value
(For technical examination)
Offset :XXXX
Factor :XX. XX
GYRO Adjust Value
DVD Err Clr Clear of DVD error log.
CDCH Err Clr Clear of CDCH error log.
P-Mecha Err Clear of control panel mechanism error.
Initial Name & DVD
Clear the user entry information, initialize the DVD error log and DVD menu setting value.
(Not clear the servo learning data.)
Initial GYROdata Initialize the GYRO value of the factory setup data.
Initial All Initialize factory setup data.
Note: After initialized should push the [RESET] key, Note: After initialized should push the [RESET] key,
or should pull out a power code 30 seconds or more, and should surely reset a main unit. or should pull out a power code 30 seconds or more, and should surely reset a main unit.
Music Srv Format All formatting of the HDD music data area.
Note: After formatted should push the [RESET] key, Note: After formatted should push the [RESET] key,
or should pull out a power code 30 seconds or more, and should surely reset a main unit. or should pull out a power code 30 seconds or more, and should surely reset a main unit.
SYS Data Format All formatting of the VAVI (addres ets.) system recording data.
Note: After formatted should push the [RESET] key, Note: After formatted should push the [RESET] key,
or should pull out a power code 30 seconds or more, and should surely reset a main unit. or should pull out a power code 30 seconds or more, and should surely reset a main unit.
Trouble of GYRO
Trouble of GPS unit
Trouble of HDD
Error log of DVD.
Error log of CDCH.
Error log of control panel mechanism.
Error log of navigation microcomputer system.
Total error counts.
[E-1] is newly data.
Error content
00 :no error
Navi+Ent :HDD,SD system error.
Navi :Navigation system error.
Ent :HDD,SD system error.
SCI :Navigation microcomputer system error.
(No.MA161)1-29