Black & Decker GW3050 Manual page 9

Features
1. Variable speed control
2. Cable restraint
3. Collection bag
4. Upper blow tube
5. Lower blow tube
6. Upper vacuum tube
7. Middle vacuum tube
8. Lower vacuum tube
9. Vac release button
10. Bag release button
11. Powerhead
12. Second handle
Assembly
@
Warning! Before assembly, make sure that the
appliance is switched off and unplugged.
@
Warning! Always wear protective gloves when
working with your blow vac.
Vacuum tube assembly (fig. A)
The vacuum tubes must be assembled together before use.
Warning!
Do not operate the appliance with the vacuum
tubes separated.
To ease assembly, apply a soapy water solution to the
u
joint area.
Align the notches (13) and the triangles (14) on the upper
u
(6) and middle (7) vacuum tubes.
Push the upper vacuum tube (6) firmly onto the middle
u
vacuum tube (7) until the triangles click into place.
Align the notches (13) and the triangles (14) on the middle
u
(7) and lower (8) vacuum tubes.
Push the middle vacuum tube (7) firmly onto the lower
u
vacuum tube (8) until the triangles click into place.
Warning! Do not separate the tubes once assembled.
Attaching the second handle (fig. B) (GW3050 Only)
Press in and hold both of the buttons (15) on the side of
u
the handle mount.
Slide the second handle (12) in place over the buttons
u
(15).
Note: Ensure that the orange button is is on the same side as
the large hole in the handle.
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
(Original instructions)
Adjusting the position of the second handle (fig. C)
(GW3050 Only)
The second handle (12) can be adjusted to provide optimum
balance and comfort.
Press in the button (15) on the left side of the handle.
u
Rotate the second handle (12) into the required position.
u
Release the button (15).
u
Warning! Ensure that the teeth on the button are correctly
aligned in slots in the handle and that the handle is secure.
Blow tube assembly (fig. D)
Align the 2 markers (16) on bottom of the upper blow tube
u
(4) and the 2 markers (17) on the bottom of the lower blow
tube (5).
Push the upper blow tube (4) firmly into the lower blow
u
tube (5) until they click into place.
Warning! Do not separate the tubes once assembled.
Fitting and removing the concentrator (fig. D)
Slide the concentrator (30) firmly onto the bottom end of
u
the lower blow tube (5). Secure the concentrator by cliping
the tab (31) onto the clip (32)
To remove, lift the clip (32) and slide the concentrator (8)
u
off the bottom of the lower blow tube(5).
Fitting and removing the rake (fig. E) (GW3050 &
GW2838 Only)
Position the rake (18) above the mount (19) on the bottom
u
of the lower blow tube (5).
Push down and slide the rake (18) firmly onto the mount
u
(19) until it clicks into place.
To remove, lift the rake release (20) and slide the rake
u
(18) off the mount (19).
Use
Switching on and off (fig. F)
Warning! Grip the product firmly when switching on.
To switch the appliance on, turn the variable speed control
u
(1) clockwise to the required setting.
To switch the appliance off, turn the variable speed
u
control (1) anti-clockwise to the off position.
Cable restraint (fig. G)
A cable restraint (2) is incorporated into the rear of the
powerhead.
Loop the cable (21) through the cable restraint (2).
u
Using your product
Warning! When using as a blower or vacuum, always wear
safety glasses. If using in dusty conditions, wear a filter mask
as well.
ENGLISH
9