Error Mode Detected By Indoor Unit - Toshiba Carrier RAV-SP180AT2-UL Service Manual

Error mode detected by indoor unit

Operation of diagnostic function
Check
Cause of operation
code
No communication from remote
E03 controller (including wireless) and
communication adapter
The serial signal is not output from
outdoor unit to indoor unit.
• Miswiring of inter-unit wire
E04
• Defective serial sending circuit on
outdoor P.C. board
• Defective serial receiving circuit on
indoor P.C. board
E08 Duplicated indoor unit address
L03 Duplicated indoor header unit
There is group wire in individual indoor
L07
unit.
L08 Unset indoor group address
L09
Unset indoor capacity
L30 Abnormal input of outside interlock
Float switch operation
P10
• Float circuit, Disconnection,
Coming-off, Float switch contact error
P12 Indoor DC fan error
4-way valve system error
P19 • After heating operation has started,
indoor heat exchangers temp. is
down.
Own unit stops while warning is output
P31
to other indoor units.
Coming-off, disconnection or short of
F01 indoor heat exchanger temp. sensor
(TCJ)
Coming-off, disconnection or short of
F02 indoor heat exchanger temp. sensor
(TC)
Coming-off, disconnection or short of
F10 indoor heat exchanger temp. sensor
(TA)
Indoor EEPROM error
F29
• EEPROM access error
Communication error between indoor
MCU
E10
• Communication error between fan
driving MCU and main MCU
Regular communication error between
indoor header and follower units and
E18
between main and sub units
Status of
Condition
air conditioner
Stop Displayed when
(Automatic reset) error is detected
Stop Displayed when
(Automatic reset) error is detected
Displayed when
Stop
error is detected
Displayed when
Stop
error is detected
Displayed when
Stop
error is detected
Displayed when
Stop
error is detected
Displayed when
Stop
error is detected
Stop Displayed when
(Automatic reset) error is detected
Stop
Displayed when
(Follower unit)
error is detected
(Automatic reset)
Stop Displayed when
(Automatic reset) error is detected
Stop
Displayed when
(Automatic reset)
error is detected
Stop
Displayed when
(Automatic reset)
error is detected
Stop Displayed when
(Automatic reset) error is detected
Stop Displayed when
(Automatic reset) error is detected
Stop Displayed when
(Automatic reset) error is detected
– 52 –
Revised : Feb. 2010
Judgment and measures
1. Check wires of remote controller and communication adapters.
• Remote controller LCD display OFF (Disconnection)
1. Outdoor unit does not completely operate.
• Inter-unit wire check, correction of miswiring
• Check outdoor P.C. board. Correct wiring of P.C. board.
• Check case tharmostat operation. (SP180 only)
2. When outdoor unit normally operates
Check P.C. board (Indoor receiving / Outdoor sending).
1. Check whether remote controller connection (Group/Individual)
was changed or not after power supply turned on
(Finish of group construction/Address check).
* If group construction and address are not normal when the
power has been turned on, the mode automatically shifts to
address setup mode. (Resetting of address)
1. Set indoor capacity (DN=11)
1. Check outside devices.
2. Check indoor P.C. board.
1. Trouble of drain pump
2. Clogging of drain pump
3. Check float switch.
4. Check indoor P.C. board.
1. Position detection error
2. Over-current protective circuit of indoor fan driving unit operated.
3. Indoor fan locked.
4. Check indoor P.C. board.
1. Check 4-way valve.
2. Check 2-way valve and check valve.
3. Check indoor heat exchanger (TC/TCJ).
4. Check indoor P.C. board.
1. Judge follower unit while header unit is [E03], [L03], [L07] or [L08].
2. Check indoor P.C. board.
1. Check indoor heat exchanger temp. sensor (TCJ).
2. Check indoor P.C. board.
1. Check indoor heat exchanger temp. sensor (TC).
2. Check indoor P.C. board.
1. Check indoor heat exchanger temp. sensor (TA).
2. Check indoor P.C. board.
1. Check indoor EEPROM. (including socket insertion)
2. Check indoor P.C. board.
1. Check indoor P.C. board.
1. Check remote controller wiring.
2. Check indoor power supply wiring.
3. Check indoor P.C. board.