Fujitsu PRIMERGY CX250 S2 Upgrade And Maintenance Manual page 8

Contents
4.6 Removing the mezzanine card bracket from the card . . . . 53
4.7 Installing the linking board . . . . . . . . . . . . . . . . . . . 54
4.8 Removing the linking board . . . . . . . . . . . . . . . . . . 56
4.9 Removing the riser module . . . . . . . . . . . . . . . . . . . 58
4.10 Installing the riser module . . . . . . . . . . . . . . . . . . . 59
4.11 Removing the memory slot air ducts . . . . . . . . . . . . . . 60
4.12 Installing the memory slot air ducts . . . . . . . . . . . . . . 61
4.13 Installing the server node in the server enclosure . . . . . . 63
4.14 Switching on the server node
4.15 Concluding software tasks . . . . . . . . . . . . . . . . . . . 64
5 Basic software procedures . . . . . . . . . . . . . . . . . . . 65
5.1 Starting the maintenance task . . . . . . . . . . . . . . . . . 65
5.1.1 Disabling SVOM boot watchdog functionality . . . . . . . . . . . 65
5.1.1.1 Viewing boot watchdog settings . . . . . . . . . . . . . . . . 65
5.1.1.2 Configuring boot watchdog settings . . . . . . . . . . . . . . 65
5.2 Completing the maintenance task . . . . . . . . . . . . . . . 67
5.2.1 Updating or recovering the system board BIOS and BMC . . . . 67
5.2.1.1 Updating or recovering the system board BIOS . . . . . . . . 67
5.2.1.2 Updating or recovering the BMC . . . . . . . . . . . . . . . 71
5.2.2 Updating RAID controller firmware . . . . . . . . . . . . . . . . 73
5.2.3 Enabling boot watchdog functionality . . . . . . . . . . . . . . . 74
5.2.4 Enabling replaced components in the system BIOS . . . . . . . 74
5.2.5 Verifying the memory mode . . . . . . . . . . . . . . . . . . . . 75
5.2.6 Verifying the system time settings . . . . . . . . . . . . . . . . 75
5.2.7 Viewing and clearing the System Event Log (SEL) . . . . . . . . 76
5.2.7.1 Viewing the SEL . . . . . . . . . . . . . . . . . . . . . . . . 76
5.2.7.2 Clearing the SEL . . . . . . . . . . . . . . . . . . . . . . . 77
5.2.8 Updating the NIC configuration file in a Linux environment . . . . 77
5.2.9 Performing a RAID array rebuild . . . . . . . . . . . . . . . . . 79
5.2.10 Looking up changed MAC / WWN addresses . . . . . . . . . . 80
5.2.10.1 Looking up MAC addresses . . . . . . . . . . . . . . . . . . 80
5.2.10.2 Looking up WWN addresses . . . . . . . . . . . . . . . . . 80
5.2.11 Using the Chassis ID Prom Tool . . . . . . . . . . . . . . . . . 81
5.2.12 Configuring LAN teaming . . . . . . . . . . . . . . . . . . . . . 82
5.2.12.1 After replacing / upgrading LAN controllers . . . . . . . . . . 82
Upgrade and Maintenance Manual
. . . . . . . . . . . . . . . . . 64
CX250 S2